Search Results

This paper describes the analysis and performance testing of a uniquely designed external heat exchanger. The heat exchanger is attached externally to an aircraft and is used to cool a laser system within the fuselage. Estimates showed insufficient cooling capacity with a conventional staggered tube array in the limited space available. Thus, a non-conventional design was developed with larger tube and fin area exposed to the ram air to increase the heat transfer performance. The basic design consists of 28 circular finned aluminum tubes arranged in two parallel banks. Wind tunnel tests were performed to simulate air and liquid flight conditions for the non-conventional parallel bank arrangement and the conventional staggered tube arrangement. Performance comparisons of each of the two designs are presented. Test results are used in a computer model of the heat exchanger to predict the operating performance for the entire flight profile.

This paper represents a first step in developing the criteria for pilot interaction with advanced controls and displays in a single pilot IFR (SPIFR) environment. The research program presented herein is comprised of an analytical phase and an experimental phase. The analytical phase consisted of a review of fundamental considerations for pilot workload taking into account existing data, and using that data to develop a SPIFR pilot workload model. The rationale behind developing such a model was based on the concept that it is necessary to identify and quantify the most important components of pilot workload to guide the experimental phase of the research which consisted of an abbreviated flight test program. The purpose of the flight tests was to evaluate the workload associated with certain combinations of controls and displays in a flight environment. This was accomplished as a first step in building a data base for single pilot IFR controls and displays.

Discontinuous wing leading-edge droop designs have been evaluated as a means of modifying wing autorotative characteristics and thus improving airplane spin resistance. Addition of a discontinuous outboard wing leading-edge droop to three typical light airplanes having NACA 6-series wing sections produced significant improvements in stall characteristics and spin resistance. Wind tunnel tests of two wings having advanced natural laminar flow airfoil sections indicated that a discontinuous leading-edge droop can delay the onset of autorotation at high angles of attack without adversely affecting the development of laminar flow at cruise angles of attack.

An investigation was conducted in the Langley 14- By 22-Foot Subsonic Tunnel to determine the low-speed aerodynamic characteristics of a powered generic NASP-like configuration in ground effect. The model was a simplified configuration consisting of a triangular wedge forebody, a rectangular mid-section which housed the propulsion simulation system, and a rectangular wedge aftbody. Additional model components included a delta wing, exhaust flow deflectors, and aftbody fences. Six-component force and moment data were obtained over an angle of attack range from −4° to 18° while model height above the tunnel floor was varied from 1/4 inch to 6 feet. Variations in freestream dynamic pressure, from 10 psf to 80 psf, and engine ejector pressure yielded a range of thrust coefficients from 0 to 0.8. Flow visualization was obtained by injecting water into the engine simulator inlets and using a laser light sheet to illuminate the resulting exhaust flow.

Wind tunnel investigations were conducted as part of an effort to develop a stability and control database for an aerospace plane concept across a broad range of Mach numbers. The generic conical design used in these studies represents one of a number of concepts being studied for this class of vehicle. The baseline configuration incorporated a 5° cone forebody, a 75.96° delta wing, a 16°leading-edge sweep deployable canard and a centerline vertical tail. Tests were conducted in the following NASA-Langley facilities spanning a Mach range of 0.1 to 6:30- by 60-Foot Tunnel,14- by 22-Foot Subsonic Tunnel, Low Turbulence Pressure Tunnel, National Transonic Facility, Unitary Plan Wind Tunnel, and the 20 Inch Mach 6 Tunnel. Data were collected for a number of model geometry variations and test conditions in each facility. This paper highlights some of the key results of these investigations pertinent to stability considerations about all three axes.

The design and analysis of the National Aerospace Plane (NASP) depends heavily on developing critical technology areas through the Technology Maturation Program (TMP). The TMP is being completed almost entirely in government laboratories with technology dissemination to all prime NASP contractors immediately upon completion of any portion of the technology development. These critical technology areas span the entire engineering design of the vehicle; included are structures, materials, propulsion systems, propellants, propulsion/airframe integration, controls, subsystems, and aerodynamics areas. There is currently a heavy dependence on Computational Fluid Dynamics (CFD) for verification of many of the classical engineering tools. Quite often the design of an aircraft uses wind tunnel tests for much of this verification, but for NASP, this task is almost impossible from a practical standpoint.

Supersonic wind tunnels with much lower stream disturbance levels than in conventional tunnels are required to advance transition research. The ultimate objectives of this research are to provide reliable predictions of transition from laminar to turbulent flow on supersonic flight vehicles and to develop techniques for the control and reduction of viscous drag and heat transfer. The experimental and theoretical methods used at NASA Langley to develop a low-disturbance pilot tunnel are described. Typical transition data obtained in this tunnel are compared with flight and previous wind-tunnel data and with predictions from linear stability theory,

Computational experiments have been performed for a few configurations in order to investigate the effects of external flow disturbances on the extent of laminar flow and wake drag. Theoretical results have been compared with experimental data for the AEDC cone, for Mach numbers from subsonic to supersonic, and for both free flight and wind tunnel environments. The comparisons have been found to be very satisfactory, thus establishing the utility of the present method for the design and development of “laminar flow” configurations and for the assessment of wind tunnel data. In addition, the present paper presents results of calculations concerning the effects of unit Reynolds numbers on transition. This phenomenon has been observed by a few experimental investigators but has been analyzed in detail for the first time in the present paper with the aid of the theoretical predictions.

Results of a recent low-speed wind-tunnel investigation conducted to define the forebody flow on a 16% scale model of the NASA High Angle-of-Attack Research Vehicle (HARV), an F-18 configuration, are presented with analysis. Measurements include force and moment data, oil-flow visualizations, and surface pressure data taken at angles of attack near and above maximum lift (36° to 52°) at a Reynolds number of one million based on mean aerodynamic chord. The results presented identify the key flow-field features on the forebody including the wing-body strake.

Large space structures will be a key element of our future space activities. They will include spacecraft such as the planned Space Station and large antenna/reflector structures for communications and observations. These large structures will exceed 100 m in length or 30 m in diameter. Concepts for construction of these spacecraft on orbit and their materials of construction provide some unique research challenges. This paper will provide an overview of our research in space construction of large structures including erectable and deployable concepts. Also, an approach to automated, on-orbit construction will be presented. Materials research for space applications focuses on high stiffness, low expansion composite materials that provide adequate durability in the space environment. The status of these materials research activities will be discussed.

An overview is given of the ongoing joint NASA/FAA/Industry Surface Traction And Radial Tire (START) Program being conducted at NASA Langley's Aircraft Landing Dynamics Facility (ALDF). The START Program involves tests using three different tire sizes to evaluate tire rolling resistance, braking, and cornering performance throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Preliminary results from recent 40 x 14 size bias-ply, radial-belted, and H-type aircraft tire tests are discussed. The paper concludes with a summary of the current program status and planned ALDF test schedule.