Search Results

Ti-alloy sheet is a high-modulus elastic-plastic material, about which the resilience in the cold-forming process is quite difficult to control. As a matter of fact, the procedure of cold-forming is composed of many cases such as tensile case and bending case. An expression of ultimate radius for bending-curvature is obtained based on tri-parameters elastic-plastic constitutive model. By classifying the cold-forming process, some typical cases of cold-forming are presented in this paper, and analytical solutions with a high precision of resilience for high-modulus elastic-plastic material such as Ti-alloy sheet under the different typical cases are obtained in this paper. The accurate analytical solutions of resilience for high-modulus elastic-plastic material presented in this paper will contribute to cold-forming process both in the mould-designing and optimizing of cold-forming procedure.

The automotive industry has a strong need for lightweight materials capable of withstanding large mechanical loads. Advanced high-strength steels (AHSS), which have high tensile strength and formability, show great promise for automotive applications, yet if they are to be more widely used, it's important to understand their deformation behavior; this is particularly important for the development of forming limit diagrams (FLD) used in stamping processes. The goal of the present study was to determine the extent to which anisotropy introduced by the rolling direction affects the local fracture strain. Three grades of dual-phase AHSS and one high-strength low-alloy (HSL A) 50ksi grade steel were tested under plane strain conditions. Half of the samples were loaded along their rolling direction and the other half transverse to it. In order to achieve plane strain conditions, non-standard dogbone samples were loaded on a wide-grip MTS tensile test machine.

Adhesive bonding has many applications in the automotive industry. The single-lapped bonded joint is the most typically used among various bonding types. This paper presents experimental research for determining the strain field of the single-lapped joint under tensile loading. The materials for the joint are epoxy-based structural adhesive and low-carbon electrolytic zinc steel plate. In the study, a DIC (digital image correlation) system was adopted to measure the strain distribution of the bonded joint during a tensile test. The bonded steel coupons in the tensile test were prepared according to the ASTM standard. During the measurement, images of the coupon joint were taken before and after the deformation process. Then the DIC system measured the strain of bonded joint by comparing two consecutive images. The measured data from the DIC was compared to data taken simultaneously from a traditional extensometer.

The automobile industry has an increasing demand for lightweight components, improve product performance, efficiency and increase safety. For optimization of design and manufacturing of these components the detail measurement of critical material properties such as strain limit, strength coefficients, anisotropy coefficients et al, are required. The most commonly used method for finding the material properties is tensile test with extensometer. But this system only provides an average strain over the specimen gauge length and is not applicable to post diffuse necking. Digital Image Correlation (DIC) technique is the latest state of art technique. Because of its capability of fast data acquisition, this technique is suited well for characterization of material properties both in the elastic and plastic ranges. It also has advantages of full field, non-contact, and considerately high precision for displacement and strain measurements.

A new, 1-D analytical engine thermal management tool was developed to model piston, oil and coolant temperatures in the Ford 3.5L engine family. The model includes: a detailed lubrication system, including piston oil-squirters, which accurately represents oil flow rates, pressure drops and component heat transfer rates under non-isothermal conditions; a detailed coolant system, which accurately represents coolant flow rates, pressure drops and component heat transfer rates; a turbocharger model, which includes thermal interactions with coolant, oil, intake air and exhaust gases (modeled as air), and heat transfer to the surroundings; and lumped thermal models for engine components such as block, heads, pistons, turbochargers, oil cooler and cooling tower. The model was preliminarily calibrated for the 3.5L EcoBoost™ engine, across the speed range from 1500 to 5500 rpm, using wide-open-throttle data taken from an early heat rejection study.

Imposing tensile stress on an edge of a sheet metal blank is a common condition in many sheet metal forming operations, making edge formability a very important factor to consider. Because edge formability varies greatly among different materials, cutting methods (and their control parameters), it is very important to have access to an experimental technique that would allow for quick and reliable evaluation of edge formability for a given case. In this paper, two existing techniques are compared: the hole expansion test and the tensile test. It is shown that the hole expansion test might not be adequate for many cases, and is prone to overestimating the limiting strain, because the burr on the sheared edge is typically smaller than what is observed in production. The tensile test represents an effective alternative to the hole expansion test. Advantages and disadvantages of each case are discussed.

A cycle-resolved test system was designed in a Two Stage Direct Injection (TSDI) Gasoline engine to simulate the engine quick start process in an Integrated Start and Generator (ISG) Hybrid Electric Vehicle (HEV) system. Based on the test system, measurement of the in cylinder HC concentrations near the spark plug under different engine coolant temperature and cranking speed conditions were conducted using a Fast Response Flame Ionization Detector (FFID) with Sampling Spark Plug (SSP) fits, then the in-cylinder equivalence ratio near the spark plug was estimated from the measured HC concentrations. In addition, the effects of the 1st injection timing, 2nd injection timing, and total equivalence ratio on the mixture formation near the spark plug were analyzed by means of experiments.

Experimental results on influence of trimming conditions on the shape of the sheared surface are combined with the results of stretching sheared samples after trimming. The objective of the research described in this paper is to study the mechanism of fracture initiation and cracks propagation during half-a-dog bone tensile test representing sheared edge stretching condition. One side of the sample had sheared surface obtained by the trimming process while the other side of the sample had a smooth surface. Significant attention was paid to understanding of fracture sources. An interrupted tensile test approach was employed to track fracture initiation and propagation during stretching of sheared surface. The results of the experimental study indicated that multiple sources of fracture were observed in the burr area for trimming with clearances exceeding 10% of the material thickness.

Experimental results on influence of trimming conditions on the shape of the sheared surface are combined with the results of stretching sheared samples after trimming. The objective of the research described in this paper is to study the mechanism of fracture initiation and cracks propagation during half-a-dog bone tensile test representing sheared edge stretching condition. One side of the sample had sheared surface obtained by the trimming process while the other side of the sample had a smooth surface. Significant attention was paid to understanding of fracture sources. An interrupted tensile test approach was employed to track fracture initiation and propagation during stretching of sheared surface. The results of the experimental study indicated that multiple sources of fracture were observed in the burr area for trimming with clearances exceeding 10% of the material thickness.

Similar laser welded blanks with same material and same gauge have been extensive applied in automobile body for improving the material utilization and extending maximum coil size. It is known that, for TWBs with dissimilar material and thicknesses, the difference of material properties and/or thickness of the welded blanks, change of the material properties in the weld seam and heat-affected zones (HAZ) as well as location and orientation of the weld seam are reasons for reduced formability. However, the plastic deformation capacity of TWBs is reduced even when the material and thickness are the same. The aim of this paper is to evaluate the deformation behaviors of similar laser welded joints. Uniaxial tensile of five laser welded joints, with 90°,60°,45°,30°and 0°weld orientations, were tested by using optical measurement-DIC (Digital Image Correlation). Strain /strain ratio distribution and evolution of each joint was analyzed and compared with base material.

The present work discusses a novel oxyfuel combustion method named internal combustion rankine cycle (ICRC) used in reciprocating engines. Water is heated up through heat exchanger by exhaust gas and engine cooling system, and then injected into the cylinder near top dead center to control the combustion temperature and in-cylinder pressure rise rate, meanwhile to enhance the thermo efficiency and work of the combustion cycle. That is because injected water increases the mass of the working fluid inside the cylinder, and can make use of the combustion heat more effectively. Waste heat carried away by engine coolant and exhaust gas can be recovered and utilized in this way. This study investigates the effect of water injection temperature on the combustion and emission characteristics of an ICRC engine based on self-designed test bench. The results indicate that both indicated work and thermal efficiency increase significantly due to water injection process.