Search Results

Many powertrain structural sub-systems are often tested under steady state conditions on a dynamometer or in a full vehicle. This process (while necessary) is costly and time intensive, especially when evaluating the effect of component properties on transient phenomena, such as driveline clunk. This paper proposes a laboratory experiment that provides the following: 1) a bench experiment that demonstrates transient behavior of a non-linear clutch damper under non-rotating conditions, 2) a process to efficiently evaluate multiple non-linear clutch dampers, and 3) generates benchmark time domain data for validation of non-linear driveline simulation codes. The design of this experiment is based on a previous experimental work on clunk. A commercially available non-linear clutch damper is selected and the experiment is sized accordingly. The stiffness and hysteresis properties of the clutch damper are assumed from the measured quasi-static torque curve provided by the manufacturer.

When developing a new engine control strategy, some of the important issues are cost, resource minimization, and quality improvement. This paper outlines how a model based approach was used to develop an engine control strategy for an Extended Range Electric Vehicle (EREV). The outlined approach allowed the development team to minimize the required number of experiments and to complete much of the control development and calibration before implementing the control strategy in the vehicle. It will be shown how models of different fidelity, from map-based models, to mean value models, to 1-D gas dynamics models were generated and used to develop the engine control system. The application of real time capable models for Hardware-in-the-Loop testing will also be shown.

An ignition delay correlation was developed for a toluene reference fuel (TRF) blend that is representative of automotive gasoline fuels exhibiting two-stage ignition. Ignition delay times for the autoignition of a TRF 91 blend with an antiknock index of 91 were predicted through extensive chemical kinetic modeling in CHEMKIN for a constant volume reactor. The development of the correlation involved determining nonlinear least squares curve fits for these ignition delay predictions corresponding to different inlet pressures and temperatures, a number of fuel-air equivalence ratios, and a range of exhaust gas recirculation (EGR) rates. In addition to NO control, EGR is increasingly being utilized for managing combustion phasing in spark ignition (SI) engines to mitigate knock. Therefore, along with other operating parameters, the effects of EGR on autoignition have been incorporated in the correlation to address the need for predicting ignition delay in SI engines operating with EGR.

In recent years, there has been a sustained effort by the automotive OEMs and suppliers to improve the vehicle driveline efficiency. This has been in response to customer demands for greater vehicle fuel economy and increasingly stringent government regulations. The automotive rear axle is one of the major sources of power loss in the driveline, and hence represents an area where power loss improvements can have a significant impact on overall vehicle fuel economy. Both the friction induced mechanical losses and the spin losses vary significantly with the operating temperature of the lubricant. Also, the preloads in the bearings can vary due to temperature fluctuations. The temperatures of the lubricant, the gear tooth contacting surfaces, and the bearing contact surfaces are critical to the overall axle performance in terms of power losses, fatigue life, and wear.

For simulation and analysis of vehicles there is a need to have a means of generating drive cycles which have properties similar to real world driving. A method is presented which uses measured vehicle speed from a number of vehicles to generate a Markov chain model. This Markov chain model is capable of generating drive cycles which match the statistics of the original data set. This Markov model is then used in an iterative fashion to generate drive cycles which match constraints imposed by the user. These constraints could include factors such number of stops, total distance, average speed, or maximum speed. In this paper, systematic analysis was done for a PHEV fleet which consists of 9 PHEVs that were instrumented using data loggers for a period of approximately two years. Statistical analysis using principal component analysis and a clustering approach was carried out for the real world velocity profiles.

This paper presents a feedback linearization control technique as applied to a Roll Simulator. The purpose of the Roll Simulator is to reproduce in-field rollovers of ROVs and study occupant kinematics in a laboratory setting. For a system with known parameters, non-linear dynamics and trajectories, the feedback linearization algorithm cancels out the non-linearities such that the closed-loop dynamics behave in a linear fashion. The control inputs are computed values that are needed to attain certain desired motions. The computed values are a form of inverse dynamics or feed-forward calculation. With increasing system eigenvalue, the controller exhibits greater response time. This, however, puts a greater demand on the translational actuator. The controller also demonstrates that it is able to compensate for and reject a disturbance in force level.

Two-stage turbochargers are a recent solution to improve engine performance, reducing the turbo-lag phenomenon and improving the matching. However, the definition of the control system is particularly complex, as the presence of two turbochargers that can be in part operated independently requires effort in terms of analysis and optimization. This work documents a characterization study of two-stage turbocharger systems. The study relies on a mean-value model of a Diesel engine equipped with a two-stage turbocharger, validated on experimental data. The turbocharger is characterized by a VGT actuator and a bypass valve (BPV), both located on the high-pressure turbine. This model structure is representative of a “virtual engine”, which can be effectively utilized for applications related to analysis and control. Using this tool, a complete characterization was conducted considering key operating conditions representative of FTP driving cycle operations.

ORVR (Onboard Refueling Vapor Recovery) canisters trap vapors during normal operations of a vehicle's engine, and during refueling. This study evaluates the relative risks involved should a canister rupture in a crash. A canister impactor was developed to simulate real-world impacts and to evaluate the canisters' rupture characteristics. Numerous performance aspects of canisters were evaluated: the energy required to rupture a canister; the spread of carbon particles following rupture; the ease of ignition of vapor-laden particles; the vapor concentration in the area of ruptured, vapor-laden canisters; and the potential of crashes to rupture and ignite canisters. Results from these five items were combined into a risk analysis.

Pedestrian research and testing at the NHTSA Vehicle Research and Test Center has recently focused on assessment of proposed ISO and EEVC head impact test procedures, and extension of these procedures to additional vehicle frontal surfaces. In addition to test parameter sensitivity evaluation, reconstruction of PCDS (Pedestrian Crash Data Study) cases with laboratory impact tests and computer simulations has been conducted. This paper presents the results of this research.

The EcoCAR Challenge team at The Ohio State University has designed an extended-range electric vehicle capable of 50 miles all-electric range via a 22 kWh lithium-ion battery pack, with range extension and limited parallel operation supplied by a 1.8 L dedicated E85 engine. This vehicle is designed to drastically reduce fuel consumption, while meeting Tier II Bin 5 emissions standards. This vehicle design is implemented in a GM crossover utility vehicle as part of the EcoCAR Challenge. This paper explains the implementation of the vehicle's control strategy in order to maintain high efficiency and improve drivability. The vehicle control strategy employs both distinct operating modes and an Equivalent Consumption Minimization Strategy (ECMS) to find the most efficient operating point. The ECMS strategy does an online search for the most efficient torque split in order to meet the driver's command.

The effectiveness of the Helmholtz resonator as a narrow band acoustic attenuator, particularly at low frequencies, makes it a highly desirable component in a wide variety of applications, including engine breathing systems. The present study investigates the influence of mean flow grazing over the neck of such a configuration on its acoustic performance both computationally and experimentally. Three-dimensional unsteady, turbulent, and compressible Navier-Stokes equations are solved by using the Pressure-Implicit-Splitting-of-Operators algorithm in STAR-CD to determine the time-dependent flow field. The introduction of mean flow in the main duct is shown to reduce the peak transmission loss and shift the fundamental resonance frequency to a higher value.

This paper presents the results of an in-depth study of the measurement of occupant kinematic response on the S-E-A Roll Simulator. This roll simulator was built to provide an accurate and repeatable test procedure for the evaluation of occupant protection and restraint systems during roll events within a variety of occupant compartments. In the present work this roll simulator was utilized for minimum-energy, or threshold type, rollover events of recreational off-highway vehicles (ROVs). Input profiles for these tests were obtained through a separate study involving autonomous full vehicle tests [1]. During simulated roll events anthropomorphic test device (ATD) responses were measured using on-board high speed video, an optical three-dimensional motion capture system (OCMS) and an array of string potentiometers.

Crankshaft angular position measurements are fundamental to all modern automotive engines. These measurements are required to control fuel injection timing as well as ignition timing. However, many other functions can be performed from such measurements through the use of advanced signal processing. These additional functions are essentially diagnostic in nature although there is potential for substitution of primary fuel and ignition control functions. This paper illustrates the application of crankshaft angular position measurement to the estimation of individual cylinder indicated and/or brake torque in IC engines from measurement of crankshaft position/velocity.

Performance characteristics of passive, active, and broadband adaptive engine mounts are compared over a wide frequency range up to 250 Hz in the context of a quarter-vehicle heave model. The optimal damping coefficient of a rubber-metal mount is determined using random vibration theory. The small-scale active mount employs proportional-plus-integral control based on linear optimal control theory. The new adaptive hydraulic mount system implements an on-off damping control mode by using engine intake-manifold vacuum and a microprocessor-based solenoid valve controller. Through analytical methods, it is observed that this adaptive mount provides most desirable dynamic performance with regard to the engine-bounce control, shock absorption and vibration isolation performance requirements. Although technical prospects of the proposed adaptive system appear promising, in-situ performance needs to be evaluated.

Flow fields generated during the intake stroke of a 4-stroke I.C. engine are studied experimentally using water analog simulation. The fluid is seeded by small flow tracer particles and imaged by two digital cameras at BDC. Using a 3-D Particle Tracking Velocimetry technique recently developed, the 3-D motion of these flow tracers is determined in a completely automated way using sophisticated image processing and PTV algorithms. The resulting 3-D velocity fields are ensemble averaged over a large number of successive cycles to determine the mean characteristics of the flow field as well as to estimate the turbulent fluctuations. This novel technique was applied to three different cylinder head configurations. Each configuration was run for conditions simulating idle operation two different ways: first with both inlet ports open and second with only the primary port open.

A prototype CO sensor based on anatase TiO2 was fabricated and tested in a Ford V6 engine. Fuel combustion was programmed to be near stoichiometric conditions, and emissions were monitored with an FT-IR analytical instrument. The sensor, positioned near the oxygen sensor in the exhaust manifold, was successfully tested for 50 cycles of revving and idling, and was observed to respond quickly and reproducibly. The sensor response was correlated to the CO concentration at specific engine temperatures and was found to vary systematically with increasing concentrations. This sensor has promising potentials to monitor the efficiency of the catalytic converter.

The soil response to traffic loads as affected by tire inflation pressure, track width and drawbar pull was measured. The change in soil physical properties caused by a John Deere 8870 tractor at two tire pressure settings and CATERPILLAR Challenger 65 and 75 tractors with 64 and 89 cm wide belt tracks, were measured at two load levels; no draft (tractor only) and tractor pulling a 12.5 m field cultivator. The Ohio State University Soil Physical Properties Measurement System was used to measure cone penetration resistance, air permeability, air-filled porosity, and bulk density. The results show the dual overinflated tires caused the greatest change, followed by the CATERPILLAR Challenger 65 track, then the CATERPILLAR Challenger 75 track, and finally dual correctly inflated tires caused the least effect on soil physical properties. These results were consistent at each depth. The effects of the two draft levels give the same ranking of the tractive units.

A new semi-analytical framework for the study of passive or active engine mounting systems is presented. It recognizes that most practical problems incorporate a nonlinear mount or isolation element and the resulting physical system, consisting of the engine, mount and flexible base, involves many degrees of freedom. Unlike linear systems, sinusoidal excitation produces a periodic response, including super- and sub- harmonics. Two example case systems are employed to illustrate key concepts of the framework. The first numerical example case involves a passive hydraulic engine mount with an inertia track. The second example case is a novel experimental system that has been developed to study active and passive, nonlinear mounting problems. New analytical and experimental results are presented and various nonlinear phenomena are considered. The impact of nonlinearity on vibratory power transmission and active control is also investigated.

One of the gray areas in the implementation of regulations limiting the generation of pollutants from mobile sources is the actual effectiveness of the exhaust gas emissions control strategy in vehicles that have been in use for some time. While it is possible today to conduct limited diagnostics with the on-board engine computer by performing periodic checks to verify the validity of the signals measured by the on-board sensors, and to measure tailpipe emissions during routine inspection and maintenance, the task of correlating these measurements with each other to provide an on-line, accurate diagnosis of critical malfunctions has thus far proven to be a very challenging task, especially in the case of misfire.

A number of automotive diagnostic equipment and procedures have evolved over the last two decades, leading to two generations of on-board diagnostic requirements (OBDI and OBDII), increasing the number of components and systems to be monitored by the diagnostic tools. The goal of On-Board Diagnostic is to alert the driver to the presence of a malfunction of the emission control system, and to identify the location of the problem in order to assist mechanics in properly performing repairs. The aim of this paper is to suggest a methodology for the development of an Integrated Powertrain Diagnostic System (EPDS) that can combine the information supplied by conventional tailpipe inspection programs with onboard diagnostics to provide fast and reliable diagnosis of malfunctions.