Search Results

Among the existing concepts that help to improve the efficiency of spark-ignition engines at part load, Controlled Auto-Ignition™ (CAI™) is an effective way to lower both fuel consumption and pollutant emissions. This combustion concept is based on the auto-ignition of an air-fuel-mixture highly diluted with hot burnt gases to achieve high indicated efficiency and low pollutant emissions through low temperature combustion. To minimize the costs of conversion of a standard spark-ignition engine into a CAI engine, the present study is restricted to a Port Fuel Injection engine with a cam-profile switching system and a cam phaser on both intake and exhaust sides. In a 4-stroke engine, a large amount of burnt gases can be trapped in the cylinder via early closure of the exhaust valves. This so-called Negative Valve Overlap (NVO) strategy has a key parameter to control the amount of trapped burnt gases and consequently the combustion: the exhaust valve-lift profile.

Nowadays, due to the high competitiveness in the automotive market, the car manufacturers and the engine developers are concentrating as many efforts as possible in order to diminish the lead-time to production and to promote cost reductions of their engine developments. As a consequence, many systems and component tests are being substituted by numerical simulations, allowing a significant reduction in the amount of engine and bench tests. The integration of individual numerical simulation tools generates the philosophy of Virtual Engine Development, which is based on the concept of simulating as much as possible the entire engine as well as its components behaviors. This paper presents the application of Virtual Engine Development (VED) in a PSA 1.4l SI engine development. Theoretical results of engine performance as well as powercell components behavior such as piston, rings, conrod, bearings, liner, engine block and cylinder head, among others, are presented and discussed.

Cycle-to-cycle variations in the pressure evolution within the cylinder of a spark ignition engine has long been recognized as a phenomenon of considerable importance. In this work, use of tools borrowed to the nonlinear dynamical system theory to investigate the time evolution of the cylinder pressure is explored. By computing a divergence rate between different pressure cycles versus crank angle, four phases during the combustion cycle are exhibited. These four phases may be identified with the four common phases evidenced by burn rate calculations [1]. Starting from phase portraits and using Poincaré sections, we also study correlations between peak pressures, IMEP and the durations from ignition to appearance of a flame kernel.

Particle Image Velocimetry (PIV) technique was used to study the in-cylinder flow motion in a single cylinder transparent spark ignition (SI) engine, with 4 valves pent-roof cylinder-head. Experiments have been firstly performed using classical PIV technique in the symmetrical plane of the combustion chamber. The instantaneous two-dimensional velocity fields show that during intake stroke, the flow has strong relatively stable structures with low cycle by cycle (CBC) variations, whereas during compression stroke, the flow consists of large unstable eddies with high CBC variations. In all cases, no large tumble-like motion was observed on instantaneous fields in the measurement plane during the intake stroke. Therefore, Stereoscopic Particle Image Velocimetry (SPIV) technique was adapted to complete the classical two-dimensional measurements and in order to have a better understanding of the in-cylinder flow during compression stroke.

For development of new engines a ‘general purpose ECU’ for spark ignition engines with up to 12 cylinders has been developed. As part of this ECU a DSP (Digital Signal Processor)-based measurement unit for high frequency combustion analysis has been integrated. In this paper, details about this signal processing platform are given. The DSP-unit has 24 analog input channels. 12 channels are used for cylinder pressure measurement; the other 12 channels are general purpose ones. For example, they can be used for ionic current analysis. Additional digital inputs allow measurement of crank speed and crank speed variations. This is an important topic for misfire detection as part of the OBD regulations.

Pilot injection gas engines are commonly used as large stationary engines. Often, the combustion is implemented as a dual-fuel strategy, which allows both mixed and diesel-only operation, based on a diesel engine architecture. The current research project focuses on the application of pilot injection in an engine based on gasoline components of the passenger car segment, which are more cost-effective than diesel components. The investigated strategy does not aim for a diesel-only combustion, hence only small liquid quantities are used for the main purpose of providing a strong, reliable ignition source for the natural gas charge. This approach is mainly driven to provide a reliable alternative to the high spark ignition energies required for high cylinder charge densities. When using such small liquid quantities, a standard common-rail diesel nozzle will apparently not be ideal regarding some general specifications.

Synthetic fuels for internal combustion engines offer CO2-neutral mobility if produced in a closed carbon cycle using renewable energies. C1-based synthetic fuels can offer high knock resistance as well as soot free combustion due to their molecular structure containing oxygen and no direct C-C bonds. Such fuels as, for example, dimethyl carbonate (DMC) and methyl formate (MeFo) have great potential to replace gasoline in spark-ignition (SI) engines. In this study, a mixture of 65% DMC and 35% MeFo (C65F35) was used in a single-cylinder research engine to determine friction losses in the piston group using the floating-liner method. The results were benchmarked against gasoline (G100). Compared to gasoline, the density of C65F35 is almost 40% higher, but its mass-based lower heating value (LHV) is 2.8 times lower. Hence, more fuel must be injected to reach the same engine load as in a conventional gasoline engine, leading to an increased cooling effect.