Search Results

This paper presents an integrated numerical and experimental approach to take best possible advantage of the common development tools at hand (1D, CFD and wind tunnel) to determine the cooling air mass flow at the different vehicle development stages. 1D tools can be used early in development when neither 3D data nor wind tunnel models with detailed underhood flow are available. A problem that has to be resolved is the dependency on input data. In particular, the pressure coefficients on the outer surface (i.e. at the air inlet and outlet region) and the pressure loss data of single components are of great importance since the amount of cooling air flow is directly linked to these variables. The pressure coefficients at the air inlet and outlet are not only a function of vehicle configuration but also of driving velocity and fan operation. Both, static and total pressure coefficient, yield different advantages and disadvantages and can therefore both be used as boundary conditions.

The object of the validation study presented in this paper is a generic vehicle, the so-called SAE body, developed by a consortium of German car manufacturers (Audi, Daimler, Porsche, Volkswagen). Many experiments have been performed by the abovementioned consortium on this object in the past to investigate its behavior when exposed to fluid flow. Some of these experiments were used to validate the simulation results discussed in the present paper. It is demonstrated that the simulation of the exterior flow is able to represent the transient hydrodynamic structures and at the same time both the generation of the acoustic sources and the propagation of the acoustic waves. Performing wave number filtering allows to identify the acoustic phenomena and separate them from the hydrodynamic effects. In a next step, the noise transferred to the interior of the cabin through the glass panel was calculated, using a Statistical Energy Analysis approach.

The most significant operation limit prohibiting the further reduction of the CO2 emissions of gasoline engines is the occurrence of knock. Thus, being able to predict the incidence of this phenomenon is of vital importance for the engine process simulation - a tool widely used in the engine development. Common knock models in the 0D/1D simulation are based on the calculation of a pre-reaction state of the unburnt mixture (also called knock integral), which is a simplified approach for modeling the progress of the chemical reactions in the end gas where knock occurs. Simulations of thousands of knocking single working cycles with a model representing the Entrainment model’s unburnt zone were performed using a detailed chemical reaction mechanism. The investigations showed that, at specific boundary conditions, the auto-ignition of the unburnt mixture resulting in knock happens in two stages.

Developments in power steering systems have been concentrated on the energy consumption as the environmental issues intensified in recent years. After the widely used hydraulic power steering system, the introduction of electric and electro-hydraulic power steering systems has shed light on the energy saving of the power steering system. In order to evaluate the energy consumption of the systems, firstly a new driving cycle was developed taking into account of both longitudinal and lateral driving behaviour. By comparing the vehicle response to the customer driving behaviour, the most similar sections on different traffic conditions were chosen therefore form the new driving cycle.

The steering wheel torque has an essential influence on the steering feel. In the chassis development process the tuning of the steering wheel torque characteristics is currently done empirically by altering the boost curve of the steering system. This paper shows how the steering assistance has to be chosen in order to achieve a harmonic steady-state steering wheel torque characteristics. It can be achieved by a linear rise of the defined steering assistance ratio versus the vehicle lateral acceleration. To determine the characteristics the gradient factor and the degressivity factor are needed only. The initial rise of the steering wheel torque versus the lateral acceleration is determined by the gradient factor. The degressivity factor describes the subsequent curvature of the characteristics.

Brake system development and testing is spread over vehicle manufacturers, system and component suppliers. Test equipment from different sources, even resulting from different technology generations, different data analysis and report tools - comprising different and sometimes undocumented algorithms - lead to a difficult exchange and analysis of test results and, at the same time, contributes to unwanted test variability. Other studies regarding the test variability brought up that only a unified and unambiguous data format will allow a meaningful and comparative evaluation of these data and only standardization will reveal the actual reasons of test variability. The text at hand illustrates that a substantial part of test variability is caused by a misinterpretation of data and/or by the application of different algorithms.

Vibration analysis of squealing brake systems under actual running conditions is a common tool for getting familiar to deflection shapes and to give straight forward hints, where and how a given system of brake and chassis might be sensitive to design evolutions. These experimental approaches -typically using accelerometers, laser-interferometry or the like- give detailed information about vibrational behavior of the structure. In contrast to this, an acoustical method as the so-called „acoustic camera” gives additional information by detecting noise sources. As can be seen from comparisons of vibrational and acoustical methods, there is not a simple connection between structure deflection and actual emission of noise. Examples are shown, what the acoustical method gives as extra information and where its limitations are. Additional benefit is expected from artificial excitation rather than running conditions, which is discussed.

In automotive open-jet wind tunnels reference velocity is usually measured in terms of a static pressure difference between two different cross-sectional areas of the tunnel. Most commonly used are two sections within the nozzle (Method 1: ΔP-Nozzle). Sometimes, the reference velocity is deduced from the static pressure difference between settling chamber and plenum (Method 2: ΔP-Plenum). Investigations in three full-scale open-jet automotive wind tunnels have clearly shown that determination of reference dynamic pressure according to ΔP-Plenum is physically incorrect. Basically, all aerodynamic coefficients, including drag coefficient, obtained by this method are too low. For test objects like cars and vans it was found that the error ΔcD depends on the test object's drag blockage in an open-jet wind tunnel.

The design of the PORSCHE wind tunnels - two facilities, one in full- and the other in quarter-scale - was determined by the demand for simulating both passenger car models and racing vehicles. One peculiarity, the very low ride height of the latter requires a reduction of the oncoming boundary layer that develops along the test- section floor. The number of difficult practical engineering problems in using and operating full-scale moving belts (*Bearman et al. [14]), led to the development of two suction systems using porous plates in the test section floor. These have been installed in the full-scale and in the 1:4 - scale windtunnels. For verification or optimization of the originally estimated suction rates required to meet realistic road conditions, a number of experiments on the road and in a moving-belt facility were conducted and the results compared to values from the suction facilities.

This paper describes the observed impact of aniline octane booster and more specifically N-Methyl Aniline (NMA) on lubricating oil, following field issues encountered in vehicles in certain areas of the world where aniline based octane booster was assumed to be used. The observed field issue was heavy sludge formation, leading to engine malfunctions. The impact of NMA on lubricating oil could first be replicated using a modified version of the CEC L-109 oxidation bench test, with oil diluted with fuel and NMA at start of test. Significant kinematic viscosity (KV100) increase at the end of test was evidenced, especially as NMA content was increased in the oil. Total base number (TBN) evaluated at end of test also showed values above fresh oil (at or above 4.5 wt% NMA) that was consistent with observations from the field. The assessment of NMA impact was then scaled up using ACEA black sludge engine test.

Numerical methods for brake squeal analysis are widely accepted in industry. The use of complex eigenvalue analysis is a successful approach to predict the appearance of squeal noise. Using simulation in an early design stage reduces time to market, saves costs, and improves the physical behavior and robustness of the brake system. State of the art of brake simulation comprises sampling for many parameter sets in a wide range of interesting values. Based on high performance, stability maps can be created in short time containing many results, which gives a deep insight into the brake behavior under varying parameters. An additional benefit of sampling is the possibility to detect parts with high potential for improving the NHV comfort. In the sequel, mathematical optimization methods like topology optimization or shape optimization are used for systematic improvements.

Enhanced technological capabilities render the application of various, increasingly complex, functional concepts for automated driving possible. In the process, the significance of automotive software for a satisfactory driving experience is growing. To benefit from these new opportunities, thorough assessment in early development stages is highly important. It enables manufacturers to focus resources on the most promising concepts. For early assessment, a common approach is to set up vehicles with additional prototyping hardware and perform real world testing. While this approach is essential to assess the look-and-feel of newly developed concepts, its drawbacks are reduced reproducibility and high expenses to achieve a sufficient and balanced sample. To overcome these drawbacks, new flexible, realistic and preferably automated virtual test methods to complement real world verification and validation are especially required during early development phases.

Optimization-based strategy planning for predictive optimal cruise control has the potential for significant improvements in passenger comfort and fuel efficiency. It is, however, associated with a high computational complexity that complicates its implementation in an electronic control unit. When implementing predictive cruise control, real-time capability must be ensured while maintaining optimal control performance in the presence of disturbance and model uncertainty. Real-time capability can be achieved either by a significant simplification of the optimization problem or by a layered control approach, combining the strategy planner with a low-level controller. Both approaches, however, are prone to deteriorate optimal control performance, particularly in the presence of disturbance. We present a model-predictive controller structure that extends the layered control approach by using the same optimization algorithm on two layers.

At specific operating conditions, the auto-ignition in the unburnt mixture that precedes the occurrence of knock in conventional SI engines happens in two stages. In a previous publication, the authors demonstrated that the low-temperature heat release significantly influences the auto-ignition behavior of the mixture, thus severely impairing the prediction capabilities of the Livengood-Wu integral that the majority of the commonly used 0D/1D knock models are based on. Consequently, a new two-stage auto-ignition prediction approach for modeling the progress of the chemical reactions was introduced. It was demonstrated that the proposed auto-ignition model predicts the occurrence of two-stage ignition and accurately considers the significant influence of low-temperature heat release on the mixture’s auto-ignition behavior at various operating conditions.

Driving fun - one of the major thrills expected by the buyers of high-performance cars - must be absolutely preserved despite all the measures required to further reduce the car's exhaust emissions and fuel consumption. Powerful engines with high BMEP levels require large unrestricted inlet and outlet valve diameters and lifts as well as a wide camshaft phasing range at least on the intake side. In terms of exhaust emissions and fuel economy such an engine layout is rather unfavourable. Its inherent drawbacks, however, can be compensated by providing for what might be called a “two-in-one” configuration which combines a low-emission concept including intake-valve lift shifting and exhaust-camshaft phasing with a high-performance-engine concept complete with a wide intake camshaft phasing range and large intake valve lifts and a Varioram intake system. With this basic layout, even high-performance sports cars are able of falling below the current ULEV limits.

One of the essential features of the new Porsche Carrera is its newly developed chassis. It offers a maximum of driving fun and active safety to customers with sporty ambitions. The front axle is a McPherson unit carried over from the predecessor model and having been thoroughly reworked. Modifications to the axle geometry and kinematics help to improve the straight-line stability and the stability during braking. The rear axle is a newly developed light-weight multi-link unit which offers a maximum of driving stability and agility (“LSA-axle”). The incorporated sub-frame allows to considerably reduce the tire noises. The car is braked by a 4-piston aluminum fixed-caliper power brake system with internally-ventilated brake disks at both the front and rear axles. The new chassis follows the principles of future-oriented light-weight construction which uses aluminum wherever this is technically and economically feasible.

Due to increasing interest in air quality concerns, worldwide legislation towards lower particle emissions is getting more and more stringent. Because of this, the development towards even cleaner internal combustion engines (ICE) with Spark Ignition (SI) is of upmost importance. Along with the development targeting higher efficiency and specific power output, Direct Injection (DI) technology became more and more important than Port Fuel Injection (PFI) and is one of the main SI engine development fields. SI engine mixture preparation (PFI or DI) and combustion produce much lower particle raw emissions than Diesel engines, but these emissions also have to be reduced to fulfill worldwide legislation and customer expectations. In this paper the focus lies on the analysis and development methods used to drastically reduce particle emissions in a gasoline-fueled DI SI engine.

The consistent measurement of airbag deployment noise places special demands on the enclosure in which the measurements are performed. The acoustical characteristics of the enclosure must be stable over long periods. It must also be sufficiently robust to withstand the loads involved. The use of a standardized enclosure provides a uniform basis for comparable measurements in different laboratories. The reasons for selecting a specific small cabin as the standard enclosure are discussed in this paper. Some examples of tests performed in the small cabin with a wide range of airbag systems are presented. High-speed film recordings of the deployment of the airbags were made simultaneously with the acoustic measurements. The stability of the acoustic environment and of the enclosure were important factors in obtaining reliable and comparable results.