Search Results

The four-microphone standing wave tube system has proven useful for measuring the absorption and transmission loss of various fibrous and non-fibrous absorbers. The system is fast, repeatable, accurate and compact. This paper discusses the advantages of the four-microphone system for measuring the transmission loss in lateral-flow absorber systems. The original four-microphone round impedance tube system and the migration to a four-microphone square tube system are discussed. The four-microphone square tube system allows effective study of filled and partially filled cavities.

Results of computations of flows, sprays and combustion performed in an optically- accessible Diesel engine are presented. These computed results are compared with measured values of chamber pressure, liquid penetration, and soot distribution, deduced from flame luminosity photographs obtained in the engine at Sandia National Laboratories and reported in the literature. The computations were performed for two operating conditions representing low load and high load conditions as reported in the experimental work. The computed and measured peak pressures agree within 5% for both the low load and the high load conditions. The heat release rates derived from the computations are consistent with expectations for Diesel combustion with a premixed phase of heat release and then a diffusion phase. The computed soot distribution shows noticeable differences from the measured one.

Numerical computations of combusting transient jets are performed under diesel-like conditions. Discussions of the structure of such jets are presented from global and detailed points of view. From a global point of view, we show that the computed flame heights agree with deductions from theory and that integrated soot mass and heat release rates are consistent with expected trends. We present results of several paramaters which characterise the details of the jet structure. These are fuel mass fractions, temperature, heat release rates, soot and NO. Some of these parameters are compared with the structure of a combusting diesel spray as deduced from measurements and reported in the literature. The heat release rate contours show that the region of chemical reactions is confined to a thin sheet as expected for a diffusion flame. The soot contour plots appear to agree qualitatively with the experimental observations.

A fast time-scale 1-D dynamic diesel particulate filter model capable of resolving the pressure pulsations due to individual cylinder firing events is presented. The purpose of this model is to investigate changes in the firing frequency component of the pulsating exhaust flow at different particulate loadings. Experimental validation data and simulation results clearly show that the magnitude and phase of the firing frequency components are directly correlated to the mass of particulate stored in a diesel particulate filter. This dynamic pressure signal information may prove particularly useful for monitoring particulate load during vehicle operation.

This paper provides a comparison of wall heat fluxes and quenching distances as one-dimensional hydrogen and heptane flames impinge head-on onto a wall. It is shown that the quenching distances for stoichiometric H2/air and C7H16/air flames under the specified conditions of this study are about the same, but the wall heat flux for the H2/air flames is approximately a factor of two greater. For lean H2/air mixtures, the quenching distance increases substantially and the wall heat flux decreases. To understand more clearly the interplay of flame speed, temperature, thermal diffusivity, and surface kinetics on the results, studies of H2/O2 flames are also carried out.

The objective of this work is to demonstrate the influence of line length concerning noise source generation using a coupled pump-motor-line model predicting superimposed pulsations of a hydrostatic transmission. This transmission model predicts superimposed flow pulsations throughout the connecting lines as well as oscillating forces dependant on system pressure variances; such oscillations are the primary sources of noise in hydrostatic transmissions which are known as FBN and SBN (Fluid Borne Noise and Structure Borne Noise), respectively. This study is a part of novel research where the prediction of superimposed noise sources considering interrelating dynamics of the pump/motor and connecting lines is accomplished and can potentially be used to develop noise source reduction strategies. An investigation considering the influence of line length demonstrates the potential to further reduce noise source generation in hydrostatic transmissions.

In this paper, a wall-modified interactive flamelet model is developed for improving the modeling of Diesel combustion. The objective is to include the effects of wall heat loss on the transient flame structure. The essential idea is to compute several flamelets with several representative enthalpy defects which account for wall heat loss. Then, the averaged flamelet profile can be obtained through a linear fit between the flamelets according to the enthalpy defect of the local gas which results from the wall heat loss. The enthalpy defect is estimated as the difference between the enthalpy in a flamelet without wall heat loss, which would correspond to the enthalpy in the gas without wall heat loss, and the gas with wall heat loss. The improved model is applied to model combustion in a Diesel engine. In the application, two flamelets, one without wall heat loss and one with wall heat loss, are considered.

Multidimensional models are increasingly employed to predict NO and soot emissions from Diesel engines. In the traditional approach, the ensemble-averaged values of variables are employed in the expressions for NO and soot formation and oxidation. In the mixture fraction averaged approach, the values of state variables and species concentrations are obtained from the structure of laminar diffusion flames. The source terms for NO and soot are then obtained by averaging across the mixture fraction coordinate with a probability density function. The clipped-Gaussian probability density function and profiles obtained by employing the OPPDIF code (part of the CHEMKIN package) for the laminar flame structure are employed in this work. The Zeldovich mechanism for NO formation and the Moss et al. formation and Nagle-Strickland-Constable oxidation model for soot have been employed to study the qualitative trends of pollutants in transient combusting Diesel jets.

The sound barrier performance of elastomeric vehicle weather seals was investigated. Experiments were performed for one bulb seal specimen following a reverberation room method. The seal wall vibration was measured using a laser Doppler vibrometer. The acoustic pressure near the seal surface was measured simultaneously, allowing the sound intensities on both side of the seal, and the sound transmission loss to be evaluated. The vibration response of the bulb seal and its sound transmission loss were then computed using the finite element method. Model predictions for the same seal geometry were found to be in excellent agreement with the experimental data within the frequency range of interest, comprised between 500 Hz and 4000 Hz.

The standard model for predicting the outcome of drop-drop collisions in sprays is one developed based on measurements in rain drops under atmospheric pressure conditions. This model includes the possible outcomes of grazing collisions and coalescence. Recent measurements with hydrocarbon drops and at higher pressure (up to 12 bar) indicate the possibility of additional outcomes: bounce, reflexive separation and drop shattering. The measurements also indicate that the Weber number range over which bounce occurs is dependent on the gas pressure. The probability of a drop-drop collision resulting in bounce increases with gas pressure. A composite model that includes all these outcomes as possibilities is employed to carry out computations in a constant volume chamber and in a Diesel engine. A sub-model for bounce that includes the pressure effects is also part of the composite model.

In recent years, there has been an interest in early-injection Diesel engines as it has the potential of achieving a more homogeneous and leaner mixture close to top-dead-center (TDC) compared to standard Diesel engines. The more homogeneous mixture may result in reduced NOx and soot emissions and higher efficiency. Diesel engines in which a homogeneous mixture is achieved close to TDC are known as Homogenous Charge Compression Ignition (HCCI) engines. PREmixed lean DIesel Combustion (PREDIC) engines in which the start of fuel injection is considerably advanced in comparison with that of the standard Diesel engine is an attempt to achieve a mode of operation close to HCCI. Earlier studies have shown that in a PREDIC engine, the fuel injection timing affects the mixture formation and hence influences combustion and pollutant formation.

Sound transmission through door and window sealing systems is one important contributor to vehicle interior noise. The noise generation mechanism involves the vibration of the seal due to the unsteady wall pressures associated with the turbulent flow over the vehicle. For bulb seals, sound transmission through the seal is governed by the resonance of the seal membranes and the air cavity within the bulb (the so-called mass-air-mass resonance). The objective of this study was to develop a finite element (FE) model to predict the sound transmission loss of elastomeric bulb seals. The model was then exercized to perform a parametric study of the influence of seveal seal design parameters. The results suggest that the sound transmission loss increases as the membrane thicknesses and/or the separation distance between the two seal walls are increased. The addition of additional internal “webs” was found to have adverse effects on the sound barrier performance.

With the need for improvement in the fuel economy along with reduction in emissions due to stringent regulations, powertrain hybridization has become the focal point of research for the automotive sector. Hydraulic hybrids have progressively gained acceptance due to their high power density and low component costs relative to their electric counterpart and many different architectures have been proposed and implemented on both on and off-highway applications. The most commonly used architecture is the series hybrid which offers great flexibility for implementation of power management strategies. But the direct connection of the high pressure accumulator to the system often results in operation of the hydraulic units in high pressure and low displacement mode. However, in this operating mode the hydraulic units are highly inefficient. Also, the accumulator renders the system highly compliant and makes the response of the transmission sluggish.

Due the increasing concern with the acoustic environment within automotive vehicles, there is an interest in measuring the acoustical properties of automotive door seals. These systems play an important role in blocking external noise sources, such as aerodynamic noise and tire noise, from entering the passenger compartment. Thus, it is important to be able to conveniently measure their acoustic performance. Previous methods of measuring the ability of seals to block sound required the use of either a reverberation chamber, or a wind tunnel with a special purpose chamber attached to it. That is, these methods required the use of large and expensive facilities. A simpler and more economical desktop procedure is thus needed to allow easy and fast acoustic measurement of automotive door seals.

An increase in the number of vehicles per capita coupled with stricter emission regulations have made the development of newer and better hybrid vehicle architectures indispensable. Although electric hybrids have more visibility and are now commercially available, hydraulic hybrids, with their higher power densities and cheaper components, have been rigorously explored as the alternative. Several architectures have been proposed and implemented for both on and off highway applications. The most commonly used architecture is the series hybrid, which requires an energy conversion from the primary source (engine) to the secondary domain. From he re, the power flows either into the secondary source (high-pressure accumulator) or to the wheels depending upon the state of charge of the accumulator. A mode-switching hydraulic hybrid, which is a combination of a hydrostatic transmission and a series hybrid, was recently developed in the author’s research group.

The latest US emission regulations require dramatic reductions in Nitrogen Oxide (NOx) emissions from vehicular diesel engines. Selective Catalytic Reduction (SCR) is the current technology that achieves NOx reductions of up to 90%. It is typically mounted downstream of the existing after-treatment system, i.e., after the Diesel Oxidation Catalyst (DOC) and Diesel Particulate Filter (DPF). Accurate prediction of input NO₂:NO ratio is useful for control of SCR urea injection to reduce NOx output and NH₃ slippage downstream of the SCR catalyst. Most oxidation of NO to NO₂ occurs in the DOC since its main function is to oxidize emission constituents. The DOC thus determines the NO₂:NO ratio as feedgas to the SCR catalyst. The prediction of NO₂:NO ratio varies as the catalyst in the DOC ages or deteriorates due to poisoning. Thus, the DOC prediction model has to take into account the correlation of DOC conversion effectiveness and the aging of the catalyst.

A gravimetric particulate measurement system, which extracts samples isokinetically from raw exhaust, is presented to quantify the particulate mass stored in diesel particulate filters. The purpose of this measurement system is to facilitate the study of wall-flow filter behavior at different particulate load levels. Within this paper, the design considerations for the particulate measurement system are detailed and its operation is described. The accuracy of the measurement is examined through a theoretical error analysis and direct experimental comparison to the differential weight of a diesel particulate filter. Experimental results are also presented to validate the ability of the system to maintain the isokinetic sampling condition.

In this paper, computations of pulsating flows in a duct with multiple inlets using the lattice Boltzmann method (LBM) are reported. As future emissions standards present a significant challenge for Diesel engine manufacturers, several options are being investigated to identify strategies to meet such regulations. Exhaust gas aftertreatment is one of the most important among them. As the performance of the various aftertreatment devices is sensitive to the flow conditions in the exhaust, a greater understanding of the flows under pulsating conditions in the presence of multiple cylinders is needed. The Lattice Boltzmann Method (LBM) is a relatively new and promising computational approach for applications to fluid dynamics problems. Two advantages of the method relative to traditional methods are ease of implementation and ease of parallelization and performance on parallel computers.

In this study, an Electro-pneumatic shifting system (E.P.S) has been designed to install on manual transmissions to make the selecting and shifting process faster and more reliable compared to manual systems. Shifting mechanism of a six speed gear box has been improved by using two tandem pneumatic cylinders, position sensors, pneumatic valves, and a controlling board based on AVR microcontroller. The central processing unit uses an electronic control system to provide the optimized operation of shift mechanism. This system can be easily adjusted in order to install externally on manual transmission systems without any changes on housing and transmission shift links.

Most of the gaseous contaminants generated inside ALS (Advanced Life Support) cabins can be degraded to some degree by microbial degradation in a biofilter. The entry of biofiltration techniques into ALS will most likely involve integration with existing physico-chemical methods. However, in this study, cabin air quality treated by only biofiltration was predicted using the one-box and biofiltration models. Based on BVAD (Baseline Values and Assumptions Document) and SMAC (Spacecraft Maximum Allowable Concentrations), ammonia and carbon monoxide will be the critical compounds for biofilter design and control. Experimentation is needed to identify the pertinent microbial parameters and removal efficiency of carbon monoxide and to validate the results of this preliminary investigation.