Search Results

Described in this paper is a component test methodology to evaluate the door trim armrest performance in an Insurance Institute for Highway Safety (IIHS) side impact test and to predict the SID-IIs abdomen injury metrics (rib deflection, deflection rate and V*C). The test methodology consisted of a sub-assembly of two SID-IIs abdomen ribs with spine box, mounted on a linear bearing and allowed to translate in the direction of impact. The spine box with the assembly of two abdominal ribs was rigidly attached to the sliding test fixture, and is stationary at the start of the test. The door trim armrest was mounted on the impactor, which was prescribed the door velocity profile obtained from full-vehicle test. The location and orientation of the armrest relative to the dummy abdomen ribs was maintained the same as in the full-vehicle test.

This paper describes the development of a three-dimensional lumped-mass structure and dummy model to study barrier-to-car side impacts. The test procedures utilized to develop model input data are also described. The model results are compared to crash test results from a series of six barrier-to-car crash tests. Sensitivity analysis using the validated model show the necessity to account for dynamic structural rate effects when using quasi-statically measured vehicle crush data.

A computational model of a mid-size sport utility vehicle was developed using MADYMO. The model includes a detailed description of the suspension system and tire characteristics that incorporated the Delft-Tyre magic formula description. The model was correlated by simulating a vehicle suspension kinematics and compliance test. The correlated model was then used to simulate a J-turn vehicle dynamics test maneuver, a roll and non-roll ditch test, corkscrew ramp and a lateral trip test, the results of which are presented in this paper. The results indicate that MADYMO is able to reasonably predict the vehicle and occupant responses in these types of applications and is potentially suited as a tool to help setup a suite of vehicle configurations and test conditions for rollover sensor testing. A suspension system sensitivity study is presented for the laterally tripped non-roll event.

An assessment tool was developed for rollover CAE signals evaluation to assess primarily the qualities of CAE generated sensor waveforms. This is a key tool to be used to assess CAE results as to whether they can be used for algorithm calibration and identify areas for further improvement of sensor. Currently, the method is developed using error estimates on mean, peak and standard deviation. More metrics, if necessary, can be added to the assessment tool in the future. This method has been applied to various simulated signals for laboratory-based rollover test modes with rigid-body-based MADYDO models.

The objective of this study was to analyze available anthropomorphic test device (ATD) responses from KARCO rear impact tests and to evaluate an injury predictive model based on crash severity and occupant weight presented by Saczalski et al. (2004). The KARCO tests were carried out with various seat designs. Biomechanical responses were evaluated in speed ranges of 7-12, 13-17, 18-23 and 24-34 mph. For this analysis, all tests with matching yielding and stiff seats and matching occupant size and weight were analyzed for cases without 2nd row occupant interaction. Overall, the test data shows that conventional yielding seats provide a high degree of safety for small to large adult occupants in rear crashes; this data is also consistent with good field performance as found in NASS-CDS. Saczalski et al.'s (2004) predictive model of occupant injury is not correct as there are numerous cases from NASS-CDS that show no or minor injury in the region where serious injury is predicted.

Macroscopic constitutive behaviors of aluminum 5052-H38 honeycombs under dynamic inclined loads with respect to the out-of-plane direction are investigated by experiments. The results of the dynamic crush tests indicate that as the impact velocity increases, the normal crush strength increases and the shear strength remains nearly the same for a fixed ratio of the normal to shear displacement rate. The experimental results suggest that the macroscopic yield surface of the honeycomb specimens as a function of the impact velocity under the given dynamic inclined loads is not governed by the isotropic hardening rule of the classical plasticity theory. As the impact velocity increases, the shape of the macroscopic yield surface changes, or more specifically, the curvature of the yield surface increases near the pure compression state.

This study applies a detailed finite element model of the human body to simulate occupant knee impacts experienced in vehicular frontal crashes. The human body model includes detailed anatomical features of the head, neck, chest, thoracic and lumbar spine, abdomen, and lower and upper extremities. The material properties used in the model for each anatomic part of the human body were obtained from test data reported in the literature. The total human body model used in the current study has been previously validated in frontal and side impacts. Several cadaver knee impact tests representing occupants in a frontal impact condition were simulated using the previously validated human body model. Model impact responses in terms of force-time and acceleration-time histories were compared with test results. In addition, stress distributions of the patella, femur, and pelvis were reported for the simulated test conditions.

The effect of epoxy-based structural foam on strength, stiffness, and energy absorption of foam filled structural components is investigated and implemented to formulate design guide-lines that can be used in enhancing weight reduction and engineering functions of systems. An experimental approach is first utilized to identify design variables such as foam density, gage, and foam layer thickness, that are needed to enhance the weight/ performance ratio of structural hat-section components. A CAE approach using non-linear, large deformation finite element analysis is used to model the hat-section components. An acceptance level of confidence in the CAE analytical tools is then established based on comparisons of results between the two approaches. Upon that, the CAE analytical tools are deployed in a sensitivity study to quantify the crush/crash characteristics of foam-filled hat-section components with respect to the changes in the afore mentioned design variables.

CAE has played a key role in development of the rollover safety technology by reducing the required number of prototypes. CAE-led Design Of Experiments (DOE) studies have helped in developing the process to minimize the number of CAE runs and to optimize use of the prototypes. This paper demonstrates the use of CAE/DOE for the design and optimization of rollover vehicle prototypes and also investigates effects of various factors in the selection of vehicle configuration for rollover sensor calibration testing. The process described herein has been successfully applied to vehicle programs. Modeling and analysis guidelines are also presented for CAE engineers to help in optimizing vehicle prototypes at program level.

A theoretical, mathematical, risk assessment procedure was developed to estimate the fraction of drivers that incurred head and thoracic AIS3+ injuries in full-engagement frontal crashes. The estimates were based on numerical simulations of various real-world events, including variations of crash severity, crash speed, level of restraint, and occupant size. The procedure consisted of four steps: (1) conduct the simulations of the numerous events, (2) use biomechanical equations to transform the occupant responses into AIS3+ risks for each event, (3) weight the maximum risk for each event by its real-world event frequency, and (4) sum the weighted risks. To validate the risk assessment procedure, numerous steps were taken. First, a passenger car was identified to represent average field performance.

State of the art electronic restraint systems rely on the acceleration measured during a vehicle crash for deployment decisions. The acceleration signal is analyzed with different criteria, among which the velocity change is a dominant criterion in almost any existing crash detection algorithm. Sensors in the front crush zone have recently been added to help develop restraint systems that comply with the new FMVSS208 and EuroNCAP regulations. Front crash sensors are usually evaluated for their velocity change during a crash and typically play a key role in the deployment decision. CAE based FEA analysis has recently been used to generate signals at the sensor module locations in crash simulations to provide supplemental information for crash sensing algorithm development and calibration. This paper presents an initial effort in developing a velocity-based crash detection algorithm, that allows broad use of CAE generated velocity time histories for system calibration.

This paper describes (1) the development of a component test methodology for testing a cooling module including radiator, condenser and trans. cooler, and (2) the associated CAE model development. A series of light truck/SUV cooling module component tests were conducted to obtain their characteristics as inputs for frontal impact and sensor modeling development. First, the cooling module component CAE sub-model was developed using soft springs along with fine-mesh sheet metal shell elements. Second, simulated sub-model results were correlated fairly well with the test data. Third, this component CAE sub-model was then incorporated into a full vehicle CAE model that was used for frontal impact (NCAP) and sensor development. Results indicated that the proposed test method for cooling module components provided consistent data and the results from cooling module sub-model can be incorporated into the full vehicle CAE model for improving the quality and accuracy of CAE models.

This paper presents an image analysis of a laboratory-based rollover crash test using camera-matching photogrammetry. The procedures pertaining to setup, analysis and data process used in this method are outlined. Vehicle roll angle and rate calculated using the method are presented and compared to the measured values obtained using a vehicle mounted angular rate sensor. Areas for improvement, accuracy determination, and vehicle kinematics analysis are discussed. This paper concludes that the photogrammetric method presented is a useful tool to extract vehicle roll angle data from test video. However, development of a robust post-processing tool for general application to crash safety analysis requires further exploration.

Full vehicle dynamic crash tests are commonly used in the development of rollover detection sensors, algorithms and occupant protection systems. However, many published studies have utilized component level rollover test fixtures for rollover related occupant kinematics studies and restraint system evaluation and development. A majority of these fixtures attempted to replicate only the rotational motion that occurs during the free flight phase of a typical full vehicle rollover crash test. In this paper, a description of the methods used to design a new dynamic component rollover test device is presented. A brief summary of several existing rollover component test methods is included. The new system described in this paper is capable of replicating the transfer of lateral energy into rotational vehicle motion that is present in many tripped laboratory based rollover crash tests.

The ability to extract and evaluate the time history of structural deformations or crush during vehicle crashes represents a significant challenge to automotive safety researchers. Current methods are limited by the use of electro-mechanical devices such as string pots and/or linear variable displacement transducers (LVDT). Typically, one end of the transducer must be mounted to a point on the structure that will remain un-deformed during the event; the other end is then attached to the point on the structure where the deformation is to be measured. This approach measures the change in distance between these two points and is unable to resolve any movement into its respective X, Y, or Z directions. Also, the accuracy of electro-mechanical transducers is limited by their dynamic response to crash conditions. The photogrammetry technique has been used successfully in a wide variety of applications including aerial surveying, civil engineering and documentation of traffic accidents.

An age-dependent, serious-to-fatal (AIS3+), thoracic risk curve was derived and evaluated for frontal impacts. The study consisted of four parts. In Part 1, two datasets of post mortem human subjects (PMHS) were generated for statistical and sensitivity analyses. In Part 2, logistic regression analyses were conducted. For each dataset, two statistical methods were applied: (1) a conventional maximum likelihood method, and (2) a modified maximum likelihood method. Therefore, four statistical models were derived — one for each dataset/statistical method combination. For all of the resulting statistical models (risk curves), the linear combination of maximum normalized sternum deflection and age of the PMHS was identified as a feasible predictor of AIS3+ thoracic injury probability. In Part 3, the PMHS-based risk curves were transformed into test-dummy-based risk curves. In Part 4, validation studies were conducted for each risk curve.

This paper compares and contrasts the modeling features present in the MVMA2D and the MADYM02D occupant simulation models. Simulations of a series of sled tests with a Hybrid II test dummy restrained with a 3-point belt system have been conducted using the MADYM02D model. The simulation results agree with the test results.

The objective of this study was to analyze available anthropomorphic test device (ATD) responses from FMVSS 301-type rear impact tests. Rear impact test data was obtained from NHTSA and consisted of dummy responses, test observations, photos and videos. The data was organized in four test series: 1) NCAP series of 30 New Car Assessment Program tests carried out at 35 mph with 1979-1980 model year vehicles, 2) Mobility series of 14 FMVSS 301 tests carried out at 30 mph with 1993 model year vehicles, 3) 301 MY 95+ series of 79 FMVSS 301 tests carried out at 30 mph with 1995-2005 model year vehicles and 4) ODB series of 17 Offset Deformable Barrier tests carried out at 50 mph with a 70% overlap using 1996-1999 model year vehicles. The results indicate very good occupant performance in yielding seats in the NCAP, Mobility and 301 MY 95+ test series.

An understanding of stiffness characteristics of different body regions, such as thorax, abdomen and pelvis of ES-2re and SID-IIs dummies under controlled laboratory test conditions is essential for development of both compatible performance targets for countermeasures and occupant protection strategies to meet the recently updated FMVSS214, LINCAP and IIHS Dynamic Side Impact Test requirements. The primary purpose of this study is to determine the transfer functions between the ES-2re and SID-IIs dummies for different body regions under identical test conditions using flat rigid wall sled tests. The experimental set-up consists of a flat rigid wall with five instrumented load-wall plates aligned with dummy’s shoulder, thorax, abdomen, pelvis and femur/knee impacting a stationary dummy seated on a rigid low friction seat at a pre-determined velocity.

The main purpose of this study was to determine the impact responses of the different body regions (shoulder, thorax, abdomen and pelvis/leg) of the ES-2re and SID-IIs dummies using rigid wall impacts under different initial test conditions. The experimental set-up consisted of a flat rigid wall with five instrumented load-wall plates aligned with dummy’s shoulder, thorax, abdomen, pelvis and knee impacting a stationary dummy seated on a rigid seat at a pre-determined velocity. The relative location and orientation of the load-wall plates was adjusted relative to the body regions of the ES-2re and SID-IIs dummies respectively.