Search Results

In regard to the evaluation of the performance of a hybrid electric vehicle (HEV), there are as many simulation methods as there are developers or researchers. They adopt different operational algorithms and they use diverse techniques to realize their logic. However, the relation among the various simulation methods has not been clearly defined. Thus, it is not easy to choose a method that would bring the best consequences in the most efficient way. Here, we present three types of backward-looking simulation algorithms for evaluating the fuel efficiency of a power-split HEV. Then the results and cost-effectiveness of each algorithm are analyzed using various component ratings over a representative driving mode. Based on the comparative analysis, the algorithm that uses equivalent fuel consumption is shown to be highly cost-effective. Also, an inductive or empirical base is set up with the results for a component sizing methodology using the recommended simulation.

As the number of user selectable electrical modules increases for passenger car, the number of cars with different combinations of option can easily exceed 100,000 cars. It results to a situation where we can not manually verify all the logical connection by making wiring combinations for each car. In this paper, we propose an algorithm that can reduce verification time for all possible wiring with available option combinations. The algorithm separates the whole wiring circuits into independent circuits and verifies the logical connections for each independent circuit with all possible options. The algorithm is time effective so the required time to verify the connections increases logarithmically as the number of possible car increases. The algorithm was implemented as software verification tool and its effectiveness was proved to be feasible.

Due to increasing amount of modules and customized options in commercial vehicles, it becomes more and more difficult to verify the circuit design. In this paper, a wire segment error locating algorithm is proposed to automate the exact wire segment error locating process. When a wrong connection is found by existing tool, guided by the exact description of wire segment error, this algorithm can locate exact wire segment error in the connection by searching for the one that has at least one neighboring segment from a correct connection.

Exterior shape of automobile can be represented by shape function through this study so that aerodynamic shape parameters can be easily controlled and changed. Also ordinary geometric information can be extracted easily from shape function model by simple calculations. It is possible to predict the aerodynamic performance of functional virtual car models which are transformed continually by developing automated program in initial design stage that includes all of above process. Innovative vehicle design process with exterior design guide will be proposed for stylist, engineer and packaging department in order to achieve low aerodynamic drag and high fuel efficiency targets.

This paper aims to establish a systematic process of developing a brand driving sound. Firstly, principal factors of a brand sound identity are extracted from factor analysis of many sample cars. As a result, brand sound positioning map is drawn using jury test data. Also, the multiple regression analysis of subjective and objective test results is carried. As a result, the principal factors are expressed by objective test data and brand sound positioning map can be easily updated from the measurement data. In addition, what should be improved for designing a target sound is reviewed. Secondly, various technologies of target sound design are discussed to involve the brand identity and vehicle’s character in driving sound. Also, an efficient tool to implement the target sound with an active sound design (ASD) system in a vehicle is introduced. This tool enables to efficiently design, tune and simulate a target sound for ASD system in a laboratory.

The optimum design process of the low-temperature condenser of a dual-loop waste heat recovery system with Rankine steam cycles for improving the fuel efficiency of gasoline automobiles has been investigated. The waste heat recovery system consists of a high-temperature (HT) loop in which water as the HT working fluid recovers waste heat only from the exhaust gas of about 700°C and a low-temperature (LT) loop in which a refrigerant as the LT working fluid recovers heat dissipation from the HT loop, and waste heat from the engine coolant of relatively low temperature. The low temperature condenser plays a role to dissipate heat from the system by condensing the low temperature loop working fluid sufficiently.

This paper describes the ground system model and algorithm for a ground level simulation tool. First, the modeling of an automotive ground system will be discussed and the algorithm for a simulation tool will be explained. We divided the model into a ground tree and a ground body. The ground tree model consists of resistance formed by the wires that connect the load to ground point with various structures and the ground body model consists of resistance between ground points in the car body. The wires with large current, such as engine ground cable, was modeled in detail by dividing the resistance into wire, bolt, and clamping resistance, in order to simulate the effect of increased contact resistance after durability test. The algorithm of the ground level simulation tool was designed to adjust the currents of the alternator, battery, and ground points in order to evaluate the various driving and load conditions.

To properly respond to demands to reduce national energy consumption and meet greenhouse gas emission targets based on environment policy, the Ministry of Trade, Industry, and Energy of Korea formed a research consortium consisting of government agencies and academic and research institutions to establish the first fuel efficiency standards for medium- and heavy-duty (MHD) commercial vehicles. The standards are expected to be introduced in 2017 as Phase 1 of the plan and will regulate trucks with a gross vehicle weight in excess of 3.5 tons and buses with a carrying capacity of more than 16 persons. Most MHD commercial vehicles are custom-made and manufactured in diversified small-quantity batch production systems for commercial or public use, resulting in difficulties in utilizing mandatory vehicle tests for fuel efficiency evaluations.

This paper describes a lateral control of autonomous large size buses on road with large curvature. In the case of long and wide commercial vehicle such as large bus, applying centerline tracking controllers in constrained environments such as large curved road (e.g. turning at intersection) may cause some concerns. Two concerns are considered: inner lane crossing related to collisions with curb and opposite lane crossing related to threatening surrounding vehicles. Considering relations between width and curvature of the road and length and width of the large size bus, the curvature of road at which inner or outer lane crossing begin to occur was calculated when centerline tracking controller was applied. Thus, the proposed algorithm optimizes motion of the bus by using model predictive control (MPC) using road geometry as constraints.

The achievement of improved NVH performance with light weighted body and low cost is very important, but difficult job to be accomplished in vehicle development. One of the various methods for the accomplishment of this goal is the optimization of the stiffness attached to a vehicle body and chassis. It is known that sufficient stiffness at the body attachments improves the flexibility of bushing rate tuning. In this paper, the theoretical consideration and analysis tool to estimate local stiffness value quantitatively are introduced. Also, the local stiffness values at various attachment locations in trimmed body are measured. The operational forces at body attachments are estimated through the TPA (Transfer Path Analysis). The suitability of attachment stiffness is judged based on the required NVH target to attain the optimal attachment stiffness in vehicle body.