Search Results

The use of fuel additives is one possible approach to reduce wear and corrosion in methanol fueled automobile engines. One hundred and six compounds added to M100 fuel in modest concentrations (1%) were tested in a Ball on Cylinder Machine (BOCM) for their ability to improve lubricity. The most promising candidates were then tested in an engine using a modified ASTM Sequence V-D wear screening test. Additive performance was measured by comparing the buildup of wear metals in the oil to that obtained from an engine fueled with neat M100. The BOCM method of evaluating the additive candidates proved inadequate in predicting abrasive engine wear under the test conditions utilized for this research program.

The objectives of this project were to investigate the corrosivity of condensate in a stoichiometric spark-ignited (SI) engine when running exhaust gas recirculation (EGR) and to determine the effects of sulfur-in-fuel on corrosion. A 2.0 L turbocharged direct-injected SI engine was operated with low-pressure EGR for this study. The engine was instrumented for visual, thermodynamic, and electrochemical analyses to determine the potential for corrosion at locations where condensation was deemed likely in a low-pressure loop EGR (LPL-EGR) engine. The electrochemical analysis was performed using multi-electrode array (MEA) corrosion probes. Condensate was also collected and analyzed. These analyses were performed downstream of both the charge air cooler (CAC) and the EGR cooler. It was found that while conditions existed for sulfuric acid to form with high-sulfur fuel, no sulfuric acid was detected by any of the measurement methods.

This paper will describe the fuel economy benefits that can be obtained when traditionally engine-driven accessories such as water pumps, oil pumps, power steering pumps, radiator cooling fans and air conditioning compressors are decoupled from the engine and are remotely driven and controlled. Simulation results for different vehicle configurations such as heavy duty trucks operated over urban and highway driving cycles and light duty vehicles such as mini vans will be presented. These results will quantify the heavy dependence of fuel economy benefits associated with different types of driving cycles.

The electrification of accessories using a fuel cell as an auxiliary power unit reduces the load on the engine and provides opportunities to increase propulsion performance or reduce engine displacement. The SunLine™ Class 8 tractor electric accessory integration project is a United States Army National Automotive Center (NAC™) initiative in partnership with Cummins Inc., Dynetek™ Industries Ltd., General Dynamics C4 Systems, Acumentrics™ Corporation, Michelin North America, Engineered Machine Products (EMP™), Peterbilt™ Motors Company, Modine™ Manufacturing and Masterflux™. Southwest Research Institute is the technical integration contractor to SunLine™ Services Group. In this paper the SunLine™ tractor electric Air Conditioning (AC) system is described and the installation of components on the tractor is illustrated. The AC system has been designed to retrofit into an existing automotive system and every effort was made to maintain OEM components whenever modifications were made.

In off-highway applications the engine torque is distributed between the transmission (propulsion) and other accessories such as power steering, air conditioning and implements. Electronic controls offer the opportunity to more efficiently manage the control of the engine and transmission as an integrated system. This paper deals with development of a steepest descent algorithm for maximizing the efficiency of hydrostatic transmission along with the engine in the presence of accessory load. The methodology is illustrated with an example. The strategy can be extended to the full hydro-mechanical configuration as required. Applications of this approach include adjusting for component wear and intelligent energy management between different accessories for possible size reduction of powertrain components. The potential benefits of this strategy are improved fuel efficiency and operator productivity.

Vehicle designers make use of vehicle performance programs such as RAPTOR™ to predict the performance of concept vehicles over ranges of industry standard drive cycles. However, the accuracy of such predictions may be greatly influenced by factors requiring more specialist simulation capabilities. For example, fuel economy prediction will be heavily influenced by the performance of the engine cooling system and its impact on the vehicle's aerodynamic drag, and the load from the air-conditioning system. To improve the predictions, specialist simulation capabilities need to be applied to these aspects, and brought together with the vehicle performance calculations through co-simulation. This paper describes the approach used to enable this cosimulation and the benefits achieved by the vehicle designer.

Atmospheric corrosion of steels, aluminum alloys, and Al-clad aluminum alloys is a problem for many civil engineering structures, commercial and military vehicles, and aircraft. Paint is usually the primary means to prevent the corrosion of steel bridge components, automobiles, trucks, and aircraft. Under ideal conditions, the coating provides a continuous layer that is impervious to moisture. At present, maintenance cycles for commercial and military aircraft and ground vehicles, as well as engineered structures, is based on experience and appearance rather than a quantitative determination of coating integrity. To improve the maintenance process and reduce costs, sensors are often used to monitor corrosion. The present suite of sensors designed to detect corrosion and marketed to predict the lifetime of the engineered components, however, are not useful for determining the condition of the protective paint coatings.

The new Beijing Automotive Industry Corporation (BAIC) engine, an evolution of the 2.3L 4-cylinder turbocharged gasoline engine from Saab, was designed, built, and tested with close collaboration between BAIC Motor Powertrain Co., Ltd. and Southwest Research Institute (SwRI®). The upgraded engine was intended to achieve low fuel consumption and a good balance of high performance and compliance with Euro 6 emissions regulations. Low fuel consumption was achieved primarily through utilizing cooled low pressure loop exhaust gas recirculation (LPL-EGR) and dual independent cam phasers. Cooled LPL-EGR helped suppress engine knock and consequently allowed for increased compression ratio and improved thermal efficiency of the new engine. Dual independent cam phasers reduced engine pumping losses and helped increase low-speed torque. Additionally, the intake and exhaust systems were improved along with optimization of the combustion chamber design.

A large amount of the heat generated during the engine combustion process is lost to the coolant system through the surrounding metal parts. Therefore, there is a potential to improve the overall cycle efficiency by reducing the amount of heat transfer from the engine. In this paper, a Computational Fluid Dynamics (CFD) tool has been used to evaluate the effects of a number of design and operating variables on total heat loss from an engine to the coolant system. These parameters include injection characteristics and orientation, shape of the piston bowl, percentage of EGR and material property of the combustion chamber. Comprehensive analyses have been presented to show the efficient use of the heat retained in the combustion chamber and its contribution to improve thermal efficiency of the engine. Finally, changes in design and operating parameters have been suggested based on the analytical results to improve heat loss reduction from an engine.

Fuel costs to operate large trucks have risen substantially in the last few years and, based on petroleum supply/demand curves, that trend is expected to continue for the foreseeable future. Non-propulsion or parasitic loads in a large truck account for a significant percentage of overall engine load, leading to reductions in overall vehicle fuel economy. Electrification of parasitic loads offers a way of minimizing non-propulsion engine loads, using the full motive force of the engine for propulsion and maximizing vehicle fuel economy. This paper covers the integration and testing of electrified accessories, powered by a fuel cell auxiliary power unit (APU) in a Class 8 tractor. It is a continuation of the efforts initially published in SAE paper 2005-01-0016.

Air conditioning and heating of heavy-duty truck cabs is an important contributor to engine efficiency, fuel economy and driver comfort. The air conditioner condenser coil and engine radiator typically share a common cooling fan, making it necessary to run the large engine cooling fan to provide condenser cooling. Engagement of the radiator cooling fan consumes a large amount of energy, further contributing to engine exhaust and noise emissions. Even under moderate temperature conditions, when the conventional engine-driven air conditioning compressor is not in use, the belt drive system adds a small speed-dependent parasitic load to the engine. Electrically driven air conditioning systems have the potential for lower energy consumption than their mechanical counterparts: Electrically driven air conditioning systems can reduce engine idle time by decoupling the air conditioner system from the engine cooling fan while offering near zero parasitic load when not in use.

As fuel economy becomes increasingly important in all markets, complete engine system optimization is required to meet future standards. In many applications, it is difficult to realize the optimum coolant or lubricant pump without first evaluating different sets of engine hardware and iterating on the flow and pressure requirements. For this study, a Heavy Duty Diesel (HDD) engine was run in a dynamometer test cell with full variability of the production coolant and lubricant pumps. Two test stands were developed to allow the engine coolant and lubricant pumps to be fully mapped during engine operation. The pumps were removed from the engine and powered by electric motors with inline torque meters. Each fluid circuit was instrumented with volume flow meters and pressure measurements at multiple locations. After development of the pump stands, research efforts were focused on hardware changes to reduce coolant and lubricant flow requirements of the HDD engine.

Copper ion exchange procedures were used to prepare zeolite-based catalysts for NOx reduction in lean (oxygen-rich) exhaust. Energy dispersive x-ray fluorescence and scanning electron microscopy analyses confirmed the presence of copper in the zeolite matrix. Zeolites were applied onto honeycomb and foam substrates, and evaluated for catalytic NOx reduction efficiency using engine exhaust. Copper-exchanged zeolite catalysts prepared for this study revealed NOx reduction of 95 percent for a period of seven minutes using previously adsorbed exhaust hydrocarbons as the reducing agent. Experiments using ethylene injection to supplement the exhaust suggest long-term and sustained NOx reduction, initially observed at 52 percent. Experimental results and performance comparisons of ZSM-5, mordenite, and Y-type zeolites are discussed. Zeolite catalysts based on Cu-mordenite showed high levels of initial NOx reduction, while results using Cu-ZSM-5 suggested better long-term activity.

This paper describes the development and evaluation of an operative catalyst for the reduction of NOx in lean exhaust. A catalyst that incorporates iron (II)-complex impregnated modified mesoporous molecular sieves (MCM-41) has been synthesized and further treated with [pd(NH3)4]Cl2 [1]. Experimental results suggest a hydrocarbon-independent reduction of NOx takes place on the iron center, and oxidation of CO is assisted by the palladium ion. The catalytic activity toward HC CO, and NOx removal was studied with simulated and real engine exhaust in the laboratory and on an engine, respectively. Engine test results demonstrate a reduction of NOx of up to 10 percent at catalyst inlet temperatures in the range of 260°C to 280°C. In this paper, possible NOx reduction pathways are also discussed.

This paper describes installation and testing of electrified engine accessories and fuel cell auxiliary power units for a Class-8 tractor. A 2.4 kW fuel cell APU (Auxiliary Power Unit) has been added to supply a 42 V power supply for electrification of air conditioning and water pump systems. A 42/12 V dual alternator was used to replace the OEM alternator to provide safety back-up in case of fuel cell failure. A QNX Real Time Operating System-based (RTOS) Rapid Prototype Electronic Control System (RPECS™), developed by Southwest Research Institute (SwRI™), is used for supervisory control and coordination between accessories and engine. A Controller Area Network (CAN) interface, from the engine Electronic Control Unit (ECU), and the RS232 interface, from the fuel cell controllers, provide system data and control for RPECS. Custom wiring to the hydrogen, water pump, and air conditioning systems also provide data to RPECS. The water pump system controller is autonomous.

Regulated gaseous, particulate and several unregulated emissions are reported from four heavy-duty diesel engines operated on the chassis version of the 1983 transient procedure. Emissions were obtained from Caterpillar 3208, Mack ENDT 676, Cummins Formula 290 and Detroit Diesel 8V-71 engines with several diesel fuels. A large dilution tunnel (57′ × 46″ ID) was fabricated to allow total exhaust dilution, rather than the double dilution employed in the stationary engine version of the transient procedure. A modal particulate sampler was developed to obtain particulate data from the individual segments of the 1983 transient procedure. The exhaust gas was analyzed for benzo(a)pyrene, metals, N2O, NO2, individual hydrocarbons and HCN. Sequential extractions were performed and measured versus calculated fuel consumptions were obtained.

This paper shows the results of an experimental investigation of the nature and characteristics of erosion of metals by high-speed impingement of airborne dust particles. The influence of various parameters upon the rate of erosion is shown. The manner in which the rate of erosion varies with certain of these parameters indicates that erosion occurs through the ductile displacement of the eroded material by the impinging dust particle.

This paper discusses the techniques and diagnostic significance of atomic absorption, atomic emission, and infrared spectrometric analysis of crankcase lubricants, with the use of supplementary data where pertinent. The parameters affecting used oil analytical data are discussed in terms of examples from Army general purpose vehicle test engines. Wear metals in used gear oils are also discussed and examples are given. Analytical methods and their applications are fully described, and the equipment and procedures for infrared spectroscopy and gas chromatography techniques are outlined.

An experimental program was designed to determine friction characteristics between brake pads and metal rotors that could indicate a brake fluid's propensity to cause chatter in wet-brakes. Friction was measured on a bench version of the John Deere wet-brake qualification system. Rotor and pad supports were made very rigid to avoid chatter in the simulator. One type of pad was run on cast-iron and mild steel rotors using two reference oils, one giving unacceptable levels of chatter and the other giving acceptable levels as previously determined in full-scale tests on the Deere system. The outstanding discriminating characteristic was the drop in friction from breakaway of the pad from the rotor. The ratio of the initial drop in the friction coefficient between unacceptable and acceptable oils for all conditions of the testing ranged from 1.7 to 2.0

Internal combustion engines (ICE) will be a part of personal transportation for the foreseeable future. One recent trend for engines has been downsizing which enables the engine to be run more efficiently over regulatory drive cycles. Due to downsizing, engine power density has increased which leads to problems with engine knock. Therefore, there is an increasing need to find a means to reduce the knock propensity of downsized engines. One of the ways of reducing knock propensity is by introducing Exhaust Gas Recirculation (EGR) into the combustion chamber, however, volumetric efficiency also reduces with EGR which places challenges on the boosting system. The individual benefits of high-pressure (HP-EGR) and low-pressure (LP-EGR) loop EGR system to assist the boosting system of a 2.0 L Gasoline Direct Injection (GDI) production engine are explored in this paper.