Search Results

From the viewpoint of reducing the environmental impacts by automobile emission, improving fuel efficiency is essential. That is why automobiles need to be lightened. However, more and more electrical systems have been necessary in an automobile to ensure safety and comfort. With the increase in the number of electrical systems, the weight of Electrical Distribution System (EDS) also has become increased. In order to reduce the weight of EDS, it was decided to evaluate a change of material from copper to aluminum. In fact, aluminum wires have been used for high-voltage wires, but they have almost never been used for low-voltage wires. SUMITOMO ELECTRIC GROUP developed an aluminum wire that is available for low-voltage wire harnesses and started mass production of the wire from October 2010. In this paper, I'm reporting mainly on our development of a new aluminum alloy that can be used for aluminum wires.

With the rapid advances in electronic control within automobiles, the junction block (J/B), primarily used for electrical transmission and electrical wiring, has begun to house electronic control units. It is evolving into an active component with smart functions that also controls vehicle devices, at the core of the wiring harness. We have developed a method using CAE to predict the fatigue failure life of J/B brackets for use as a design-assist tool in the early stage of J/B development. Failure of J/B brackets starts with the repetitive stress generated in the brackets during resonance. This stress is maximum at primary natural vibration which is the lowest frequency during resonance. By accurately estimating the above-mentioned stresses using CAE, we established a method to determine the number of vibrations at which fatigue failure of the J/B bracket would occur (fatigue failure life) from the fatigue failure life characteristics of the material.

In the expansion of composite material application, it is one of the most important subjects in assembly of aircraft structure how drilling of composite/metal stack should be processed in an efficient way. This paper will show the result of development of a drill bit for CFRP/Aluminum-alloy stack by Kawasaki Heavy Industries (KHI) and Sumitomo Electric Hardmetal (SEH). In order to improve workability and economic performance, the drill bit which enables drilling CFRP/Al-alloy stack: at 1 shot; from both directions; without air blow and coolant (just usual vacuuming); was required. A best mix drill bit which has smooth multi angles edge and pointed finishing edge was produced as a result of some trials. Developed drill bit achieved required performance and contributed to large cost reduction, labor hour saving, production speed increase and work environment improvement.

Fiber-optic data links have been developed for use in vehicle navigation systems, especially for the communication of CD data. The links consist of transmitters, receivers, and cable assemblies. The transmitters, which include only LEDs, must have driver circuits on their exteriors. In the receiver section, a PD, an amplifier, and a TTL compatible comparator are all integrated into the custom designed IC which is hermetically sealed into an originally developed metal package. Small optical connectors and heat-resistant plastic fiber cords with sufficient reliability and good operability for automotive uses have also been developed.

We developed a remote control unit (Hereinafter referred to as the controller) employing mainly an eight-directional joystick with push-button function. And it has good operational feeling. As previous joysticks generated operator feeling via springs, so the click sensation could not be felt. We thought that a good click feeling can be obtained by applying rubber contacts to the switch element of the joystick. Additionally, in order to include the push-button functions, we supported the operant unit with biaxial bearing and employed a sliding-knob structure penetrating this operant unit. Also in order to obtain a uniform operator feeling for all eight directions, we applied eight rubber contacts and gave the switches eight contacts. In order to restrain the rise in IC costs with the increase to eight contacts, we introduced an eight-contact four- output switch matrix and a one-contact three-electrode pattern.

Pollution is worsening in cities. The exhaust gas from vehicles is the main cause of air pollution in cities. The major drawback of the diesel engine is the Particulate Matter (PM) contained in the exhaust fumes which is also said to lead to cancer. For about 20 years many tests have been conducted in order to reduce PM in diesel exhaust gas. However the exhaust gas in present diesel engines contains a significant amount of PM. This is because there is no practical material for the Diesel Particulate Filter (DPF). Conventional ceramic materials have problems such as cracking and melting during regeneration and conventional metal materials lack adequate corrosion resistance for practical use. The authors present a new type of DPF made of metal porous matter (Celmet) which is designed with a thermal construction and simple control system in order to solve the problem of diesel exhaust gas.

A new double-layer valve seat insert has been developed for use in high performance diesel engine of passenger car. The seat layer is composed of a sintered alloy of a high wear resistance and a high heat resistance. The base layer is composed of a sintered alloy of a higher heat resistance than that of the seat layer. This double-layer valve seat insert was proven to have good wear resistance and heat resistance in a durability test on the diesel engine with a turbocharger system.

The weight of wire harnesses increases with the growing number of systems used in the vehicle in recent years. For the purpose of reducing the weight of wire harnesses, aluminum instead of the conventional copper is getting popular as a wire conductor. The conventional Al wire, however, is not able to be used for small gauge wires such as the sizes of 0.35mm2 and 0.5mm2 and wires used in the engine compartment due to its insufficient conductor strength. For this reason, we tried to develop a stronger aluminum alloy that has conductor strength equivalent to or stronger than that of copper. For the first time in the industry, we have successfully developed a high-strength aluminum alloy wire. Starting with the application of 0.35mm2 wire for engine wire harnesses, we began mass production in April 2015. This paper reports the development of high-strength aluminum alloy that can be used for small gauge wires and wires used in the engine compartment.