Search Results

In a current competitive automotive market, weight and cost optimization is the need of an hour. Therefore it is important to explore use of alternative material which has less weight, low manufacturing cost and better strength. This paper presents methodology to achieve cost & weight reduction through use of Austempered Ductile Iron (ADI) instead of alloy forging. ADI casting has lower density, physical properties at par with alloy forgings and lower manufacturing cost. Pivot arm is the one of the critical component of twin axle steering system which transfers the hydraulic torque from steering gearbox to second forward axle via linkage system. In order to design lightweight pivot arm, existing chromium alloy steel material is replaced with the Austempered ductile iron (ADI). Pivot arm is designed and validated digitally as well as bench test and results are found to be meeting cost and weight targets.

This paper discusses the test setup and methodology required to validate complete lift axle assembly for simulating the real time test track data. The correlation of rig vs track is discussed. The approach for reduction of validation time by eliminating few of the non-damaging tracks/events, its correlation with real life condition is discussed, and details are presented. With increased competition, vehicle development time has reduced drastically in recent past. Bench test procedure using accelerated test cycle discussed in this paper will help to reduce development time and cost. Process briefed in this paper can also be used for similar test specification for other structural parts or complete suspension system of heavy commercial vehicles.

In the current customer centric automotive market, NVH is one of the prime focus for the automotive industry. Almost all light commercial vehicles in the market are with hydraulic power steering system. Hydraulic power steering pump is heart of the steering system which circulates the hydraulic oil to steering gear for assisting the driver. One of the NVH problem which is inevitable with the hydraulic vane pump is humming noise and this is perceived as an irritant by end user. This paper describes a novel technique for reducing the humming noise which is perceived at driver ear level. Base vehicle level objective measurements is carried out to set the acceptance criteria. Existing design is optimized as per CAE iterations and vehicle updated with the multiple solutions and objective measurements are recorded. Driver ear level noise reduction upto 4 dB(A) perceived which meets acceptance criteria.

Small commercial vehicles (SCVs) are the drivers of a major part of India’s indirect economy, providing the most efficient means of transport. With the introduction of BS-VI norms, some major overhauls have been done to the SCV models to meet BS VI norms in challenging timeline for early market entry. This forced to automotive designers towards challenge of cost competitiveness as well as refinement level to survive in this competitive market. This paper explains the systematic approach used to overcome challenges of higher tactile vibrations, higher in-cab noise because of BS VI requirement in 2 cycle engine required for small commercial vehicle. The solutions were need to be worked out without compromising the other performance attributes like total cost of ownership, fuel economy, ease of servicing and cost effectiveness.

Nowadays, E- commerce and logistics business model is booming in India with road transport as a major mode of delivery system using containers. As competition in such business are on rise, different ways of improving profit margins are being continuously evolved. One such scenario is to look at reducing transportation cost while reducing fuel consumption. Traditionally, aero dynamics of commercial vehicles have never been in focus during their product development although literature shows major part of total fuel energy is consumed in overcoming aerodynamic drag at and above 60 kmph in case of large commercial vehicle. Hence improving vehicle exterior aerodynamic performance gives opportunity to reduce fuel consumption and thereby business profitability. Also byproduct of this improvement is reduced emissions and meeting regulatory requirements.

The small commercial vehicle business is driven by demand in logistic, last mile transportation and white goods market. And to cater these businesses operational and safety needs, they require closed container on vehicle. As of now, very few OEM’s provide regulatory certified container vehicle because of constrains to meet inertia class of the vehicle. This paper focuses on design of a durable and extremely reliable container, made of the low-cost economy class glass fibre & core material. The present work provides the means to design the composite container for the N1 category of the vehicle. The weight of after-market metal container ranges between 300-350 Kg for this category of vehicle, which affects the overall fuel economy and emission of the vehicle. A detailed CAE analysis is done to design composite container suitable to meet inertia class targets and to achieve weight reduction of 30-40% as compared to metal container.

In current scenario, Light Commercial Vehicle segment (7 ton - 9.6 ton) is gradually experiencing a shift in the focus from being just a goods carrier to a vehicle which is developed to take care of driver's safety and comfort in terms of better ergonomics and aesthetics. As compared to their conventional counterparts the new generation Light Commercial Vehicles are better equipped and tuned to cater to the changing needs of the consumers. In view of this, refinement at the sub system level is becoming far more critical. On the same lines, the present work discusses a refined brake system for Light Commercial Vehicles where the conventional pneumatic system is replaced with Dual Air Over Hydraulic (DAOH) to achieve cost and weight advantages without compromising on its performance. However, during the development process, a lot of issues were observed with respect to the braking performance and the brake pedal feel.

The entire commercial vehicle industry is moving towards weight reduction to leverage on the latest materials available to benefit in payload & fuel efficiency. General practice of weight reduction using high strength steel with reduced thickness in reference to Roark’s formula does not consider the stiffness & dent performance. While this helps to meet the targeted weight reduction keeping the stress levels within the acceptable limit, but with a penalty on stiffness & dent performance. The parameters of stiffener like thickness, section & pitching are very important while considering the Stiffness, bucking & dent performance of a dumper body. The Finite Element Model of subject dumper body has been studied in general particularly on impact of dent performance and is correlated with road load data to provide unique solution to the product. The impact of payload during loading of dumper is the major load case.

Apart from being an active safety system the brake system represents an important aspect of the vehicle dynamics. The vehicle retardation and stopping distance completely depend upon the performance of brake system and the functionality of all components. However, the performance prediction of the entire system is a challenging task especially for a complex configuration such as multi-axial vehicle applications. Furthermore, due to its complexity most often the performance prediction by some methods is limited to static condition. Hence, it is very important to have equivalent mathematical models to predict all performance parameters for a given configuration in all different conditions This paper presents the adopted system modelling approach to model all the elements of the pneumatic brake system such as dual brake valve, relay valve, quick release valve, front and rear brake actuators, foundation brake etc.

Recycle, Reuse, Repair is an established process for sustainability. There are many ways in which cutting tools can be recycled. Be it by reshaping a used up throwaway type tool [1] or by redesigning a tool holder for the use of unused cutting edges [2]. This paper explores the possibility of reuse of HSS drills that are used for making long oil holes in automobile parts like crankcase (cylinder block), cylinder head, crankshaft, etc. Design/manufacture of such drills is peculiar by virtue of their size and length and are also known as thick web high helix drills. Making of oil holes entails use of drills that are 500 to 600 mm long depending on the size of the component. In most of the long oil hole drilling operations, a limited portion of the drill is useable. This is because there is a possibility of fouling of the holding elements with guiding element, or with the part being drilled and the chance of accidental damage to part or machine.

Small goods carrier and passenger vehicles powered by Naturally Aspirated (NA) Direct Injection (DI) diesel engines are popular in Indian automobile market. However, they suffer from inherently high radiated noise and poorly perceived sound quality. This paper documents the steps taken to reduce the radiated noise level from such an engine through structural modifications of major noise radiating components identified in the sound power analysis. The work is summarized as follows; Baseline radiated noise measurements of power train and identification of major noise sources through sound intensity mapping and noise source ranking (NSR) in an Engine Noise Test Cell (ENTC) Design modifications for identified major sources in engine structure Vehicle level assessment of the radiated noise in a Vehicle Semi-Anechoic Chamber (VSAC) for all the design modifications. A reduction of 7 dB at hot idle and 4 - 8 dB in loaded speed sweep conditions was observed with the recommended modifications.

New generation light commercial vehicles are expected to have lower steering effort, high self centering and less turning circle diameter covering large variety of wheelbases from 2.8 m to 4.5 m even with mechanical steering and keeping same number of total turns of steering wheel compared to old generation light commercial vehicles. To address above requirements, below parameters related to steering and rigid front axle were studied. 1 Caster angle of front axle 2 Steering compliance and Steering ball joint articulation angle 3 Front axle kingpin axial play 4 Steering gearbox ratio 5 Pitman arm length The effect of above parameters was studied in isolation and combination. This optimization has resulted in least steering effort and least turning circle diameter in light commercial vehicles with mechanical steering and option of power steering could be eliminated for cost reduction.

For sustainability in automobile manufacturing, recycle, reuse, and repair of used up cutting tools is now an established process. Although many types of tools were designed for one time use and then throw, an increasing awareness of the impact on the natural resources have made manufacturers to put some of these back to use or sell it back to suppliers who have put up a mechanism to extract the elements e.g. Tungsten and use it for manufacturing of new tools. There are many ways in which cutting tools can be recycled. Be it by reshaping a used up throwaway type tool [1], by redesigning of a tool holder for the use of unused cutting edges [2] or reusing short length drills that are used in making of long oil holes in crank case, cylinder head, cam shaft or connecting rods [3]. This paper demonstrates successful use of used up crankshaft grinding wheels.

In case of new generation of commercial vehicles, three shaft transmissions are designed with press fitted gears on counter shaft. It allows user to save the cost of transmission manufacturing by considerable amount. In case of heavy commercial vehicles, which are being used in abusive conditions such as mining and off-road applications, it becomes absolutely necessary to ensure that the gears press fit should withstand the continuous loads and impact loads. There are design guidelines available to ensure proper fit and torque carrying capacity between the mating parts. Still, there are gear slippage, shaft and gear breakage failures in the field. In this scenario, there is a need to develop bench test procedure which will capture such failures in the prototype stage. Looking at the failures in the field, it is necessary to capture all above hidden failures in design validation phase.

Lift axles of heavy commercial vehicles are deployed to handle increased payload. These axles of Commercial vehicles are made of low alloy carbon steel materials. Lift axles are designed in hollow condition for weight reduction opportunity. Two types of tube materials are used for the manufacturing of lift axles. These are either Cold Drawn Seamless (CDS) tubes or Hot Finished Seamless (HFS) tube material. The vanadium micro-alloyed steel grade, 20MnV6 is an excellent choice for the manufacturing of lift axles. The 20MnV6 has favorable mechanical properties for lift axles and also offers good weldability. However, lift axles made of 20MnV6 when manufactured in hot-finished condition, shows significant scatter in terms of durability performance. This requires further heat treatment of 20MnV6 to be deployed for reducing the scatter in the material properties to reduce scatter in durability performance and thus increasing the reliability of the lift axles.

The crankshaft is the component which transmits dynamic loads from cylinder pressure and inertial loads in engine operating conditions. Because of its crucial importance in functioning of engine and requisite to sustain high dynamic and torsional loading, crankshaft fatigue life is desired to be higher than the predicted engine operating life. Performance of the crank train in diesel engine applications largely depends on the components of its mass elastic system. Flywheel is one such component whose design affects the life of crankshaft. In the present study, the crank train comprising of torsional vibration damper, crankshaft and flywheel along with clutch cover is considered for analysis. Crankshaft dynamic simulation is performed with multi body dynamics technique, fatigue safety factors of crankshaft are calculated with dynamic loads under engine operating conditions.

IC Engine manufacturers are constantly in pursuit of better sealability of cylinder head and engine block interface for meeting performance and durability targets. In order to overcome variation in torque - tension characteristics of cylinder head bolt because of friction variations, yield based clamping are being extensively adopted. Current study is done on torque - tension characteristics of a cylinder head bolt with a controlled quality. The paper enumerates the experimental setup representing a sub 1 liter all aluminum engine's head-block joinery. Studies on torque - tension characteristics of cylinder head bolt and the effect of sealing interface using a cost effective single layer steel gasket are being discussed in the paper. Subject work has led to a successful implementation of angular torque parameters on head bolts to meet functional and durability targets.

The necessity of hybrid vehicles and electric vehicles is well known by now for reasons like fossil fuel depletion, climate change, emission norms mandated by regulations etc. With the addition of electric motor, battery and associated power electronics, the cost of powertrain and hence the vehicle goes up, which is often a hindrance for OEMs and end-customers. With the objective to make a cost-effective strong hybrid, Tata Motors has approached this problem by taking economies of scale approach i.e. developing an add-on gearbox module, which can fit a family of cars, in a P3-off axis hybrid configuration to an electrically actuated AMT. This paper presents the preliminary simulations, which show this architecture yielding a reduction of fuel consumption by ~20% for a B-class sedan/compact SUV of ~1800kg and ~15% improvement in acceleration performance. Additionally, the design and packaging studies show the fitment possibility in a highly congested powertrain bay.

Today’s competitive market demands for low cost passenger cars with lighter, smaller size, peppy response and fuel efficient engines and having world class NVH refinement levels. For such requirements, it is essential to optimize the product starting from the design conceptual stage, considering all performance aspects. Generally, three cylinder engines, due to less reciprocating masses, compared to four-cylinder engine, are said to be fuel efficient for the same capacity. Nevertheless, NVH problems caused by inherent imbalance forces and couples remain as drawback of the three-cylinder engine. However, through optimal design of the crank train, control of cylinder to cylinder pressure variation, stiffening of the engine structure, optimizing the integration with a vehicle through proper design of mounts, NVH refinement levels can be improved.

In automobile design, a rear-engine layout mainly espoused for small entry-level cars and light commercial vehicles for three reasons - packaging, traction, and ease of manufacturing. The aim of this paper is to strategize cooling system of rear-mounted engine of a small gasoline car. Radiator and cooling fan packaged close to engine at rear of the car for simple packaging. Efficient thermal management ensured by robust overheat protection stratagem using EMS software. DFSS, a disciplined problem prevention approach that helps in achieving the most optimum design solution and provides improved and cost effective quality products; is used to finalize an optimum design based on the analysis of the various tests carried out as per DOE [1]. This paper is about designing a distinctive cooling system of a car having rear-mounted engine with rear radiator but front mounted HVAC system [2].