Search Results

Beside the main trend technologies such as downsizing, down speeding, external exhaust gas recirculation, and turbocharging in combination with Miller cycles, the optimization of the mechanical efficiency of gasoline engines is an important task in meeting future CO2 emission targets. Friction in the piston assembly is responsible for up to 45% of the total mechanical loss in a gasoline engine. Therefore, optimizing piston assembly friction is a valuable approach in improving the total efficiency of an internal combustion engine. The form honing process enables new specific shapes of the cylinder liner surface. These shapes, such as a conus or bottle neck, help enlarge the operating clearance between the piston assembly and the cylinder liner, which is one of the main factors influencing piston assembly friction.

Wet-running multi-plate clutches and brakes are important components of modern powershift gearboxes and industrial powertrains. In the open stage, drag losses occur due to fluid shear. The identification of drag losses is possible by experiment or CFD-simulation. For the calculation of the complex fluid flow of an open clutch, CFD-approaches such as the volume of fluid (vof) method or the Singhal cavitation model are applicable. Every method has its own specific characteristics. This contribution sets up CFD-calculation models for different clutches with diverse groove designs. We present results of calculations in various operating conditions obtained from the Singhal cavitation model and the vof method. The usage of modern commercial CFD-Tools (Simerics MP+) results in short calculation times.

The study of oil emission is of essential interest for the engine development of modern cars, as well as for the understanding of hydrocarbon emissions especially during cold start conditions. A laser mass spectrometer has been used to measure single aromatic hydrocarbons in unconditioned exhaust gas of a H2-fueled engine at stationary and transient motor operation. These compounds represent unburned oil constituents. The measurements were accompanied by FID and GC-FID measurements of hydrocarbons which represent the burned oil constituents. The total oil consumption has been determined by measuring the oil sampled by freezing and weighing. It has been concluded that only 10 % of the oil consumption via exhaust gas has burned in the cylinders. A correlation of the emission of single oil-based components at ppb level detected with the laser mass spectrometer to the total motor oil emission has been found.

This study discusses model-based injection rate estimation in common rail diesel injectors exhibiting aging phenomena. Since they result in unexpected injection behavior, aging effects like coking or cavitation may impair combustion performance, which justifies the need for new modeling and estimation approaches. To predict injection characteristics, a simulation model for the bottom section of the injector is introduced, with a main focus on modeling the hydraulic components. Using rail pressure and control piston lift as inputs, a reduced model is then derived in state-space representation, which may be used for the application of an observer in hardware-in-the-loop (HIL) environments. Both models are compared and validated with experimental data, with which they show good agreement. Aging effects and nozzle wear, which result in model uncertainties, are considered using a fault model in combination with an extended Kalman filter (EKF) observer scheme.

Due to its molecular structure, methane provides several advantages as fuel for internal combustion engines. To cope with nitrogen oxide emissions high levels of excess air are beneficial, which on the other hand deteriorates the flammability and combustion duration of the mixture. One approach to meet these challenges and ensure a stable combustion process are fuelled prechambers. The flow and combustion processes within these prechambers are highly influenced by the position, orientation, number and overall cross-sectional area of the orifices connecting the prechamber and the main combustion chamber. In the present study, a water-cooled single cylinder test engine with a displacement volume of 0.5 l is equipped with a methane-fuelled prechamber. To evaluate influences of the aforementioned orifices several prechambers with variations of the orientation and number of nozzles are used under different operating conditions of engine speed and load.

Existing electronic combustion engine control systems only guarantee a desired air-to-fuel-ratio λ in stationary operation. In order to achieve the desired λ also in in-stationary use of the engine, it is necessary to use new-technology-based control systems. Artificial Intelligence provides methods to cope with difficulties like wide operation range, unknown nonlinearities and time delay. We will propose a strategy for control of a Spark Ignition Engine to determine the mass of air inside the combustion chambers with the highest accuracy. Since Neural Networks are universal approximators for multidimensional nonlinear static functions they can be used effectively for identification and compensation purposes of unknown nonlinearities in closed control loops.

In the near future, pollutant and GHG emission regulations in the transport sector will become increasingly stringent. For this reason, there are many studies in the field of internal combustion research that investigate alternative fuels, one example being oxygenated fuels. Additionally, the design of engine components needs to be optimized to improve the thresholds of clean combustion and thus reduce particulates. Simulations based on PRiME 3D® for dynamic behaviors inside the piston ring group provide a guideline for experimental investigation. Gas flows into the combustion chamber are controlled by adjusting the piston ring design. A direct comparison of regular and synthetic fuels enables to separate the emissions caused by oil and fuel. This study employed a mixture of dimethyl carbonate (DMC) and methyl formate (MeFo).

In this study, a fully optically accessible single-cylinder research engine is the basis for the visualization and generation of extensive knowledge about the in-cylinder processes of mixture formation, ignition and combustion of oxygenated synthetic fuels. Previous measurements in an all-metal engine showed promising results by using a mixture of dimethyl carbonate and methyl formate as a fuel substitute in a DISI-engine. Lower THC and NOx emissions were observed along with a low PN-value, implying low-soot combustion. The flame luminosity transmitted via an optical piston was split in the optical path to simultaneously record the natural flame luminosity with an RGB high-speed camera. The second channel consisted of OH*-chemiluminescence recording, isolated by a bandpass filter via an intensified monochrome high-speed camera.

Aging effects such as coking or cavitation in the nozzle of common rail (CR) diesel injectors deteriorate combustion performance. This is of particular relevance when it comes to complying with emission legislation and demonstrates the need for detecting and compensating aging effects during operation. The first objective of this paper is to analyze the influence of worn nozzles on the injection rate. Therefore, measurements of commercial solenoid common rail diesel injectors with different nozzles are carried out using an injection rate analyzer of the Bosch type. Furthermore, a fault model for typical aging effects in the nozzle of the injector is presented together with two methods to detect and identify these effects. Both methods are based on a multi-domain simulation model of the injector. The needle lift, the control piston lift and the pressure in the lower feed line are used for the fault diagnosis.

Measurement techniques for piston ring rotation, engine oil emission and blow by have been implemented on a single-cylinder petrol engine. A novel method of analysis allows continuous and fast real-time identification of the piston ring rotation of the two compression rings, while the mass-spectrometric analysis of the exhaust gas delivers the cylinder oil emission instantly and with a high temporal resolution. Only minor modifications to the piston rings were made for the insertion of the γ-emitters, the rings rotate freely around the circumference of the piston. The idea of this setup is that through online observation at the test bench, instant feedback of the measured variables is available, making it possible to purposefully select and compare measurement points. The high time resolution of the measurement methods enables the analysis of dynamic effects. In this article, the measurement setup and evaluation method is described.

The recent growth of available computational resources has enabled the automotive industry to utilize unsteady Computational Fluid Dynamics (CFD) for their product development on a regular basis. Over the past years, it has been confirmed that unsteady CFD can accurately simulate the transient flow field around complex geometries. Concerning the aerodynamic properties of road vehicles, the detailed analysis of the transient flow field can help to improve the driving stability. Until now, however, there haven’t been many investigations that successfully identified a specific transient phenomenon from a simulated flow field corresponding to driving stability. This is because the unsteady flow field around a vehicle consists of various time and length scales and is therefore too complex to be analyzed with the same strategies as for steady state results.

For large bore Otto gas engines a high specific power output and therefore high engine load promises a rise in engine efficiency on one hand and on the other hand a reduction of the performance-related investment. However, this can negatively affect the emissions performance, operating limits especially in regards to knocking, and component life. For this reason at the Chair of Internal Combustion Engines (LVK) of the Technical University of Munich (TUM) experiments with a 4.77 l single-cylinder research engine were carried out to investigate the boundary conditions, potentials and downsides of combustion processes with a brake mean effective pressure beyond current series engines and higher than 30 bar. The objective in this investigations was to achieve BMEP > 30 bar with an engine configuration that widely represents the current series-production status. Hence, an unscavenged prechamber spark plug, a series Piston and Valve timing were used.

In the “high-pressure-dual-fuel” (HPDF) combustion process, natural gas is directly injected into the combustion chamber with high pressure at the end of the compression stroke, and burned in a diffusion flame similar to conventional diesel combustion. As natural gas does not self-ignite when injected into hot air, a small amount of diesel fuel is injected directly before the gas injection to provide an ignition source for the gas jets. The HPDF combustion process has the potential to substantially reduce methane slip compared to today’s state of the art premixed lean burn gas engines, and furthermore, phenomena like knocking or misfire can be avoided completely. In this paper, the influences of in-cylinder air density and swirl motion on HPDF combustion is studied via high-speed recordings in a fully optically accessible 4.8 Liter single-cylinder research engine.

One way of increasing the efficiency of a gasoline engine is to operate it in lean-burn mode. However, a lean mixture in the combustion chamber reduces its ignitability, which leads to poor combustion stability and even misfires. This investigation presents a solution to this problem using an active pre-chamber for each cylinder, into which fuel can be injected separately and in which ignition takes place. This increases the ignition energy in the main combustion chamber, thus enabling stable combustion. Cylinder-specific feedback control of the fuel quantity injected into the pre-chambers was implemented on the basis of measured cylinder pressures so as to compensate for injector component deviations, achieve maximum efficiency, and prevent increased emissions. Since combustion delay and burn duration are dependent on the fuel mass injected into the pre-chamber, an additional feedback control for the center of combustion (MFB50) was integrated along with the fuel quantity controller.

Over the past years, the question as to what may be the powertrain of the future has become ever more apparent. Aiming to improve upon a given technology, the internal combustion engine still offers a number of development paths in order to maintain its position in public and private mobility. In this study, an innovative combustion process is investigated with the goal to further approximate the ideal Otto cycle. Thus far, similar approaches such as Homogeneous Charge Compression Ignition (HCCI) shared the same objective yet were unable to be operated under high load conditions. Highly increased control efforts and excessive mechanical stress on the components are but a few examples of the drawbacks associated with HCCI. The approach employed in this work is the so-called Spark Assisted Compression Ignition (SACI) in combination with a pre-chamber spark plug, enabling short combustion durations even at high dilution levels.

Laser induced fluorescence (LIF) is used to investigate oil transport mechanisms under real engine conditions. The engine oil is mixed with a dye that can be induced by a laser. The emitted light intensity from the dye correlates with the residual oil at the sensor position and the resulting oil film thicknesses can be precisely determined for each crank angle. However, the general expectation is not always achieved, e.g. an exact representation of piston ring barrel shapes. In order to investigate the responsible lubrication effects of this behavior, a new cavitation algorithm for the Reynolds equation has been developed. The solution retains the mass conservation and does not use any switch function in its mathematical approach. In contrast to common approaches, no vapor-liquid ratio is used, but one or several bigger bubbles are approximated, as have been observed in other experiments already.

Deep neural network models have been widely used for environment perception of intelligent vehicles. However, due to models’ innate probabilistic property, the lack of transparency, and sensitivity to data, perception results have inevitable uncertainties. To compensate for the weakness of probabilistic models, many pieces of research have been proposed to analyze and quantify such uncertainties. For safety-critical intelligent vehicles, the uncertainty analysis of data and models for environment perception is especially important. Uncertainty estimation can be a way to quantify the risk of environment perception. In this regard, it is essential to deliver a comprehensive survey. This work presents a comprehensive overview of uncertainty estimation in deep neural networks for environment perception of intelligent vehicles.

In order to fulfill future exhaust emission regulations, the variety of subsystems of internal combustion engines is progressively investigated and optimized in detail. The present article mainly focuses on studies of the flow field and the resulting discharge coefficients of the intake and exhaust valves and ports. In particular, the valves and ports influence the required work for the gas exchange process, as well as the cylinder charge and consequently highly impact the engine’s performance. For the evaluation of discharge coefficients of a modern combustion engine, a stationary flow test bench has been set up at the Chair of Internal Combustion Engines (LVK) of the Technical University of Munich (TUM). The setup is connected to the test bench’s charge air system, allowing the adjustment and control of the system pressure, as well as the pressure difference across the particular gas exchange valve.

Synthetic fuels for internal combustion engines offer CO2-neutral mobility if produced in a closed carbon cycle using renewable energies. C1-based synthetic fuels can offer high knock resistance as well as soot free combustion due to their molecular structure containing oxygen and no direct C-C bonds. Such fuels as, for example, dimethyl carbonate (DMC) and methyl formate (MeFo) have great potential to replace gasoline in spark-ignition (SI) engines. In this study, a mixture of 65% DMC and 35% MeFo (C65F35) was used in a single-cylinder research engine to determine friction losses in the piston group using the floating-liner method. The results were benchmarked against gasoline (G100). Compared to gasoline, the density of C65F35 is almost 40% higher, but its mass-based lower heating value (LHV) is 2.8 times lower. Hence, more fuel must be injected to reach the same engine load as in a conventional gasoline engine, leading to an increased cooling effect.

In order to predict reality as accurately as possible leads to the fact that numerical models in automotive vibroacoustic problems become increasingly high dimensional. This makes applications with a large number of model evaluations, e.g. optimization tasks or uncertainty quantification hard to solve, as they become computationally very expensive. Engineers are thus faced with the challenge of making decisions based on a limited number of model evaluations, which increases the need for data-efficient methods and reduced order models. In this contribution, variational autoencoders (VAEs) are used to reduce the dimensionality of the vibroacoustic model of a vehicle body and to find a low-dimensional latent representation of the system.