Search Results

The low-NOx regulation for heavy duty trucks proposed by California’s Air Resources Board (CARB) will present a significant challenge to truck, engine and aftertreatment system manufacturers. This regulation will include a new test cycle representative of low-load operation. With low-load cycles, NOx conversion by the SCR (selective catalytic reduction) system is limited primarily by the exhaust temperature; thus, thermal management will dominate development. Simulation can be used to examine different thermal management strategies, and to define high-level requirements for new components. In this study, modeling was used to investigate SCR performance on two different low-load cycles, including the one selected by CARB for the low-NOx regulation. First, the “thermal deficit” of the cycle was quantified using a constant heat input.

Exhaust systems traditionally require a specific amount of muffler volume to reduce sound levels appropriately. However, as hybridization evolves, the packaging area becomes smaller, reducing available muffler space and requiring alternative solutions to attenuate exhaust sound with less volume. Passive exhaust valves are a key solution, leveraging the physics of the exhaust (flow, temperature, and pressure) to cycle the valve. Passive exhaust valves typically operate in a closed position under low-flow conditions (low engine speeds and loads), which helps to reduce low-frequency boom, moderately increasing backpressure when it is not detrimental to engine efficiency. Conversely, under higher engine speed and load operating conditions, when exhaust flow increases and backpressure is critical to achieve desired power output, the passive valve opens to reduce its impact.

As Selective Catalytic Reduction (SCR) NOx abatement systems gain commercial acceptance and popularity, the need for efficiency predictive capabilities increases. To this end, a flow bench was developed capable of varying steady state inputs (temperature, flow rate and NOx concentration). The efficiencies of various SCR systems was measured and compared. This concept of a steady state flow bench approach allows for an efficient and cost effective means to evaluate comparable system designs.

2010 and future EPA regulations introduce stringent Oxides of Nitrogen (NOx) reduction targets for diesel engines. Selective Catalytic Reduction (SCR) of NOx by Urea over catalyst has become one of the main solutions to achieve these aggressive reductions. As such, urea solution is injected into the exhaust gas, evaporated and decomposed to ammonia via mixing with the hot exhaust gas before passing through an SCR catalyst. Urea mixers, in this regard, are crucial to ensure successful evaporation and mixing since its liquid state poses significant barriers, especially at low temperature conditions that incur undesired deposits. Intensive efforts have been taken toward developing such urea mixers, and multiple criteria have been derived for them, mainly including NOx reduction efficiency and uniformity. In addition, mixers must also satisfy other requirements such as low pressure drop penalty, mechanical strength, material integrity, low cost, and manufacturability.

An active diesel particulate filter (DPF) regeneration system is evaluated, which applies secondary fuel injection (SFI) directly within the exhaust system upstream of a diesel oxidation catalyst (DOC). Diesel fuel is oxidized in the presence of a proprietary catalyst system, increasing exhaust gas temperatures in an efficient and controlled manner, even during low engine-out gas temperatures. The exotherms produced by secondary fuel injection (SFI) have been evaluated using two different DOC volumes and platinum catalyst loadings. DOC light-off temperatures were measured using SFI under steady-state conditions on an engine dynamometer. A ΔT method was used for the light-off temperature measurements – i.e., the minimum DOC inlet gas temperature at which the exothermic reaction increases the outlet gas temperature 20°C or greater than the inlet temperature.

A unique validation method is proposed for mount designs of Lean NOx Traps (LNT's), in which characteristic curves of failure points as functions of thermal cycles and vibration amplitudes are generated. LNT's are one of the several new types of emissions control devices applied to Diesel Exhaust Systems, and they reduce the amount of NOx through chemical adsorption. Desulfation must occur nearly every hour, which involves raising the inlet gas temperature of the LNT to around 700°C to “burn off” sulfur from the catalyst, which otherwise would decrease its catalytic activity. This temperature is held for several minutes, and its cyclic occurrence has a negative effect on the long-term performance of the support mat, a major component of its mount design. As substrate temperatures increase, shell temperatures do as well, and thermal growth differences between the ceramic substrate and metallic shell cause the gap between them, which is filled by the support mat, to increase.

Diesel Particulate Filter Systems offer excellent opportunities to reduce the emitted soot through their filtration potential, but periodic burning of the collected soot is necessary. This is referred to as Regeneration, which occurs every few hundred miles and requires gas temperatures to increase to nearly 600°C. As the soot burns, it creates an exothermic response, increasing DPF exit temperatures potentially to 800°C or higher. Such extremes create thermal management concerns as the hot gases exit the tailpipe, particularly during low speeds or idling conditions. Methods to manage such thermal concerns are presented in this study, evaluating passive and active options.

In order to satisfy China IV (equivalent to EU IV) emission regulations, an unconventional design concept was proposed with injector closely coupled with SCR can body. The benefit of this design is that the urea decomposition pipe was removed or drastically shortened, resulting in much smaller packaging space and lower cost of the whole system. However, the resulting short urea mixing distance generates concerns on low urea mixing efficiency and risks of urea deposits. In particular, airless urea injectors tend to generate incomplete evaporation of urea water solution, resulting in high risks of urea deposits. New aftertreatment mixing structures need to be developed to resolve these technical challenges.

In order to satisfy China IV emissions regulations, a unique design concept was proposed with injector closely coupled with Selective Catalytic Reduction (SCR) system outer body. The benefit of this design is significant in cost reduction and installation convenience. One paper was published to describe the vertical inlet layout [1]; this work is the second part describing applications of this concept to horizontal inlet configurations. For horizontal inlet pipe, two mixing pipe designs were proposed to avoid urea deposit and meet EU IV emission regulations. Computational Fluid Dynamics (CFD) technique was used to evaluate two design concepts; experiments were performed to validate both designs. CFD computations and experiments give the same direction on ranking of the two decomposition tubes. With the straight decomposition pipe design and unique perforated baffle design, no urea deposits were found; in addition, the emission level satisfied EU IV regulations.

New emissions standards for oxides of nitrogen (NOx) in on-road diesel vehicles are effective in 2010, and a common approach applies urea selective catalytic reduction (SCR). Urea is injected into the exhaust and decomposes to form ammonia, which chemically reacts with NOx as it passes through an SCR catalyst. Ammonia is corrosive and negatively affects typical stainless steels used in exhaust applications, but these corrosive impacts have not yet been quantified in an exhaust system. Two unique corrosion tests are performed on a number of various stainless steel samples, illustrating such performance concerns with 409, while offering alternatives with much better performance, including cost-effective options. The method applied is described, yielding performance criteria through appearance, weight loss, and corrosion pit depth.