Search Results

We have developed a new semi-active suspension, called Piezo TEMS, that uses piezoelectric ceramic for suspension control with sensor and actuator. It improves remarkably driveability with the firm damping force mode and enhances the ride comfort with the soft damping force mode immediately after the road surface input exceeding the threshold level.

Ongoing research on active stabilizers involves not only control of the roll angle of the vehicle based on steering input but also improving ride comfort by reducing roll vibration caused by the antiphase road surface input. In that context, roll skyhook control, which applies skyhook theory to provide feedback on the vehicle roll and drive the actuators, has already been presented. Although vibration in all frequency bands can be reduced if there is no control delay, time lags or phase delays in control elements such as the communication, computation, low-pass filter, or actuators can amplify vibration. Consequently, a sufficient effect of controlling cannot be obtained. This paper will address wheelbase filtering, which produces a frequency that minimizes roll oscillation, and is used to suppress the influence of the undesirable vibration.

This paper reports the results of a study into a preview control that uses the displacement of the road surface in front of the vehicle to improve for front and rear actuator responsiveness delays, as well as delays due to calculation, communication, and the like. This study also examined the effect of a preview control using the eActive3 electric active suspension system, which is capable of controlling the roll, pitch, and warp modes of vehicle motion.

This paper investigates a new approach to the quantification technique for road induced vehicle interior noise and vibration within the frequency range up to 40 Hz. By employing the least squares method, both vertical and fore-aft load to each wheel were quantified using transfer function and actual vibration response of the vehicle driven on a road. The coupled structural-acoustic vehicle model using the finite element method, which is also detailed in this paper, is combined with the quantified input load to simulate road induced interior noise and vibration response. Experimental verification, which indicates reasonable accuracy of the simulation, and an application for the prototype development are also presented.

A cooperative research program has been completed evaluating the relative impact of fuel composition and engine design features on the emissions and fuel economy of a Toyota light-duty diesel truck. The fuel set was blended from commercially available refinery stocks and consisted of eight fuels with independently varying 10% and 90% distillation temperatures and aromatic content. The engine design variables included two compression ratios and three injector types with different fuel flow characteristics, and three injection timings. The main fuel effects observed were increasing hydrocarbon and particulate emissions with increasing aromatic content and, to a much lesser degree, increasing emissions with increasing 10% and 90% point. Changing from the standard fuel injectors to the reference injectors, which had both a higher nozzle opening pressure and a higher initial fuel flow rate, resulted in a substantial reduction in all emissions and improvements in fuel economy.

JAMA (Japan Automobile Manufactures Association, Inc.)'s guideline for car navigation systems is being decided on displayed the amount of information while driving. The position of a display and the estimated equation, which could be applied from a passenger car to a heavy truck, was studied. The evaluation index was the distance which drivers could become aware of a preceding vehicle by their peripheral vision, because car accidents while drivers glance at an in- vehicle display are almost the rear end collisions. As the results, the lower limit of a position of an in-vehicle display for a passenger car was 30 degrees, and a heavy truck was 46 degrees.

As wireless technologies evolve, in-vehicle information services are becoming more and more essential to vehicle users. In contrast with information services in the home, in-vehicle information services emphasize the use of information to make driving more comfortable, rather than simply displaying information during driving. In particular, traffic information is, unlike other kinds of information, effective in getting to a destination and therefore, must be real-time to be useful. In Japan, car navigation systems have a large market penetration; dynamic route guidance systems (DRGS) operating in concert with navigation systems have been popular since 1995. This paper discusses mobile information services including DRGS. The focus is on the Japanese market where navigation technologies are the most advanced.

Attaining optimum balance between longitudinal compliance and sideforce compliance steer in a torsion beam suspension system is a challenging task. We developed a suspension in which the longitudinal compliance is almost doubled and the side force compliance steer amount is improved by using the link effect of toe control links. This suspension system has been developed to realize excellent controllability, stability, riding comfort, and road noise performance.

Vehicle rollovers are one of the more severe crash modes in the US - accounting for 32% of all passenger vehicle occupant fatalities annually. One design enhancement to help prevent rollovers is Electronic Stability Control (ESC) which can reduce loss of control and thus has great promise to enhance vehicle safety. The objectives of this research were (1) to estimate the effectiveness of ESC in reducing the number of rollover crashes and (2) to identify cases in which ESC did not prevent the rollover to potentially advance additional ESC development. All passenger vehicles and light trucks and vans that experienced a rollover from 2006 to 2015 in the National Automotive Sampling System Crashworthiness Database System (NASS/CDS) were analyzed. Each rollover was assigned a crash scenario based on the crash type, pre-crash maneuver, and pre-crash events.

The object of this study is to investigate the possibility of improving ride comfort, and develop a new damping control system. We supposed and analyzed the ideal damping control for vehicle suspension system using optimal control strategy. The parameter study shows the effect of reducing vehicle acceleration from road excitation. To achieve the same performance with a more simple and lower cost control strategy, we introduce another control strategy called ‘Skyhook model’ proposed by D.Karnopp. Continuously damping control system is developed based on this to avoid some problems that might be caused in the case of a two-stage switching system. Further more, variable control gain depends on vehicle vibration circumstances introduced to realize the adaptation of various road conditions. Using computer simulation and testing the experimental vehicle, effectiveness of this system is evident and the possibility of ride comfort improvement is verified by using this control.