Search Results

This paper contains an analysis of the potential safety benefits of electronic stability control (ESC) for single unit trucks and tractor semitrailers within the U.S. operating environment. It is based on research projects [1,2] which combined hardware-in-the-loop simulation and vehicle testing with the analysis of independent crash datasets using engineering and statistical techniques to estimate the probable safety benefits of stability control technologies for 5-axle tractor-semitrailer vehicles and single unit trucks. The characteristics of ESC-relevant crashes involving these two vehicle classes were found to be very different as were the control strategies needed for crash avoidance. Rollover was the dominant ESC relevant crash type for tractor semitrailers while loss of control was the dominant ESC relevant crash for straight trucks.

As part of a system for structural health monitoring, it is required to determine the spatial and temporal distributions of vertical loads arising from heavy trucks driven on flexible bridge structures. An instrumented truck is used to generate the input loads and estimate the load time histories. The truck can carry a range of sensors; however direct measurement of vertical tire loads between the tires and the structure is not considered realistic. The dynamic loads are to be estimated from the sensor outputs. These are affected by both truck and bridge dynamics and these must be accounted for within the load estimation process. Estimation may be susceptible to many factors including static mass distribution, vehicle longitudinal motion, variations in lateral position on the bridge, as well as any surface unevenness.

Seat belt anchorage locations have a strong effect on occupant protection. Federal Motor Vehicle Safety Standard (FMVSS) 210 specifies requirements for the layout of the anchorages relative to the seating reference point and seat back angle established by the SAE J826 H-point manikin. Sled testing and computational simulation has established that belt anchorage locations have a strong effect on occupant kinematics, particularly for child occupants using the belt as their primary restraint. As part of a larger study of vehicle geometry, the locations of the anchorage points in the second-row, outboard seating positions of 83 passenger cars and light trucks with a median model year of 2005 were measured. The lower anchorage locations spanned the entire range of lap belt angles permissible under FMVSS 210 and the upper anchorages (D-ring locations) were distributed widely as well.

As passenger car use becomes more common in developing countries, the number of child passengers killed and injuries also increases. Rates of child restraint use appear to be much lower in developing countries than in the U.S. or Europe. One barrier to increased restraint use is the relatively high cost of child restraints in low- and middle-income countries, where the cost of child restraints can be similar to the U.S. but incomes and typical vehicle prices are much lower. As part of a broader effort to improve child passenger safety worldwide, a team at the University of Michigan has begun development of a child restraint that is intended to be fabricated using low-cost technology in developing countries with minimal capital investment. Providing a design that has been tested successfully to regulatory standards may reduce barriers to entry and allow the restraints to be marketed at low prices.

Federal Motor Vehicle Safety Standard (FMVSS) 213 specifies a bench seat that is used in dynamic testing of child restraint systems. To assess the representativeness of the FMVSS 213 bench, data from 54 passenger cars, minivans, and SUVs were analyzed to quantify the side-view profile of the seat centerlines in second-row, outboard seats. SAE J826 H-point measurements were performed on all seats and on the FMVSS 213 bench. A landmark-based resampling method was used to obtain a meaningful average seat contour after aligning on H-point. Principal component analysis and regression were conducted to quantify the effects of seat cushion angle, cushion length, and back angle on the seat profile. When aligned on H-point, the cushion length and surface angles of the FMVSS 213 bench were similar to the mean contour, except that no seats were as flat as the bench profile.

In this study, two sled series were conducted with a sled buck representing a compact vehicle. The first series of tests focused on the effects of crash pulse, impact angle, occupant size, and front seat location on rear seat occupant restraint with a generic rear-seat belt system without pre-tensioner or load limiter. The second series of tests focused on investigating the benefit of using advanced features for rear-seat occupant restraint in the most severe crash condition in the first sled series. The first series of tests include 16 test conditions with two impact angles (0° and 15°), two sled pulse (soft and severe), and four ATD sizes (HIII 6YO, HIII 5th female, HIII 95th male, and THOR-NT) with two ATDs in each test. The driver seat was located at the mid position, while the front passenger seat was positioned such that a constant distance between the ATD knee and the front seat is achieved.

Rollover accidents are of special concern for commercial vehicle safety. The relatively low roll stability of the commercial truck promotes rollover and contributes to the number of truck accidents and injuries. This Research Report takes an in-depth look at the mechanics and contributing factors to rollover accidents and helps to identify prevention strategies.

A detailed understanding of the size, shape, and postures of children is required to design effective restraint systems for protecting children in motor vehicle crashes. Compiled and edited by experts in the fields of anthropometry, ergonomics, and child restraint, this book includes 14 important papers which provide a comprehensive overview of the methods for collecting, analyzing, and applying child anthropometry data for crash safety purposes. A detailed understanding of the size, shape, and postures of children is required to design effective restraint systems for protecting children in motor vehicle crashes. Compiled and edited by experts in the fields of anthropometry, ergonomics, and child restraint, this book includes 14 important papers which provide a comprehensive overview of the methods for collecting, analyzing, and applying child anthropometry data for crash safety purposes.