Search Results

The aim of this work is to apply an innovative adaptive ℒ1 techniques to control flutter phenomena affecting highly flexible wings and to evaluate the efficiency of this control algorithm and architecture by performing the following tasks: i) adaptation and analysis of an existing simplified nonlinear plunging/pitching 2D aeroelastic model accounting for structural nonlinearities and a quasi-steady aerodynamics capable of describing flutter and post-flutter limit cycle oscillations, ii) implement the ℒ1 adaptive control on the developed aeroelastic system to perform initial control testing and evaluate the sensitivity to system parameters, and iii) perform model validation and calibration by comparing the performance of the proposed control strategy with an adaptive back-stepping algorithm. The effectiveness and robustness of the ℒ1 adaptive control in flutter and post-flutter suppression is demonstrated.

Connected and Autonomous Vehicles (CAV) rely on information obtained from sensors and communication to make decisions. In a Cooperative Vehicle Safety (CVS) system, information from remote vehicles (RV) is available at the host vehicle (HV) through the wireless network. Safety applications such as crash warning algorithms use this information to estimate the RV and HV states. However, this information is uncertain and sparse due to communication losses, limitations of communication protocols in high congestion scenarios, and perception errors caused by sensor limitations. In this paper we present a novel approach to improve the robustness of the CVS systems, by proposing an architecture that divide application and information/perception subsystems and a novel prediction method based on non-parametric Bayesian inference to mitigate the detrimental effect of data loss on the performance of safety applications.

This paper presents the concept of a dual latent heat sink for thermal management of pulse heat generating electronic systems. The focus of this work is to verify the effectiveness of the concept during charging through experimentation. Accordingly, custom components were built and a prototype version of the heat sink was fabricated. Experiments were performed to investigate the implementation feasibility and heat transfer performance. It is shown that this heat sink is practicable and helps in arresting the system temperature rise during charging (period of pulse heat load).

The 2,4-dimethyl-3-pentanone (DIPK) is a promising biofuel candidate for automotive applications that is produced by the endophytic fungal conversion process which can be optimized for widespread utilization. There are some studies in the literature on combustion properties of DIPK, such as ignition delay times and laminar burning velocity (LBV) measurements. However, most studies are conducted one atmospheric (atm) pressure which are far away from the high-pressure conditions present inside reciprocating engines. Therefore, we present LBV measurements at high pressures up to 10 atm for this fuel using a spherical flame speed facility. It is known that the flame in a constant volume chamber develops cellular structure (hydrodynamic instability) as the initial pressure increases because of the reduction in flame thickness. In addition, the diffusional-thermal instability prevents experiments for rich mixtures because of the reduction of Lewis number (Le).

Complex aerospace engineering systems require innovative methods for performance monitoring and anomaly detection. The interface of a real-time data stream to a system for analysis, pattern recognition, and anomaly detection can require distributed system architectures and sophisticated custom programming. This paper presents a case study of a simplified interface between Programmable Logic Controller (PLC) real-time data output, signal processing, cloud computing, and tablet systems. The discussed approach consists of three parts: First, the connectivity of real-time data from PLCs to the signal processing algorithms, using standard communication technologies. Second, the interface of legacy routines, such as NASA's Inductive Monitoring System (IMS), with a hybrid signal processing system. Third, the connectivity and interaction of the signal processing system with a wireless and distributed tablet, (iPhone/iPad) in a hybrid system configuration using cloud computing.

An innovative nonlinear simulation approach for high power density synchronous generator systems is developed and implemented. Due to high power density, the generator operates in nonlinear region of the magnetic circuit. Magnetic Finite Element Analysis (FEA) makes nonlinear simulation possible. Neural network technique provides nonlinear functions for system level simulation. Dynamic voltage equation provides excellent mathematical model for system level simulations. Voltage, current, and flux linkage quantities are applied in Direct-Quadrature (DQ) rotating frame. The simulated system includes main machine, exciter, rectifier bridge, bang-bang control, and PI control circuitry, forming a closed loop system. Each part is modeled and then integrated into the system model.

This paper reviews the literature which identifies the causes, consequences and cures for engine knock as it affects high performance engines. The physical events of normal and abnormal combustion are described. The observed variations in combustion phenomenon are explained through chemical kinetics. A mathematical model of combustion which can predict knock in an engine cylinder is summarized. Several mechanisms of knock induced damage are outlined. Design and operating considerations which affect an engine's propensity to knock are discussed. Terms that have become associated with combustion in general and the knocking phenomenon in particular are collected and examined

A power electronics module was equipped with an evaporative spray cooling nozzle assembly that served to remove waste heat from the silicon devices. The spray cooling nozzle assembly took the place of the standard heat sink, which uses single phase convection. The purpose of this work was to test the ability of spray cooling to enable higher power density in power electronics with high temperature coolant, and to be an effective and lightweight system level solution to the thermal management needs of aerospace vehicles. The spray cooling work done here was with 95 °C water, and this data is compared to 100 °C water/ propylene glycol spray cooling data from a previous paper so as to compare the spray cooling performance of a single component liquid to that of a binary liquid such as WPG. The module used during this work was a COTS module manufactured by Semikron, Inc., with a maximum DC power input of 180 kW (450 VDC and 400 A).

Effective thermal management and removal of the waste heat generated at diode arrays is critical to the development of high-power solid-state lasers. Thermal design must be considered in the packaging of these arrays. Two different packages with heat dissipation through spray cooling are evaluated experimentally and numerically. Their overall performance is compared with other packaging configurations using different heat removal approaches. A novel packaging design is proposed that can fulfill the requirements of low thermal resistance, temperature uniformity among emitters in the diode array, low coolant flow rate, simplicity and low assembly cost. The effect of temperature uniformity on the pumping efficiency for gain media is examined for our novel packaging design. The thermal stress induced by temperature variation within an emitter is also considered.

This study introduces a new practical calibration approach of ductile fracture models by performing square punch tests on metal sheets. During square punch tests, ductile fracture occurs at either the corner of die or punch radius when applying different clamping loads and lubrication conditions. At the corner of die radius, in-plane pure shear is induced at the intersection between the side-walls and the flange by combined tension and compression. On the other hand, the material at the corner of the punch radius is under combined bending and biaxial tension. The material studied in this paper is advanced high strength steel (AHSS) DP780 from ArcelorMittal. Isotropic J2 plasticity model with mixed Swift-Voce hardening rule is calibrated from uniaxial tensile tests.

Preliminary investigations of nonlinear modeling of aircraft synchronous generators using neural networks are presented. Aircraft synchronous generators with high power density tend operate at current-levels proportional to the magnetic saturation region of the machine's material. The nonlinear model accounts for magnetic saturation of the generator, which causes the winding flux linkages and inductances to vary as a function of current. Finite element method software is used to perform a parametric sweep of direct, quadrature, and field currents to extract the respective flux linkages. This data is used to train a neural network which yields current as a function of flux linkage. The neural network is implemented in a Simulink synchronous generator model and simulation results are compared with a previously developed linear model. Results show that the nonlinear neural network model can more accurately describe the responsiveness and performance of the synchronous generator.

The making of a quilt is an interesting process. Historically, a quilt is a canvas of work made from old pieces of cloth cut into squares or whatever shape that make a nice connected pattern and then stitched together. The quilt could be random pieces that is not related to each other. In most recent years and more common cases, a quilt is made of different pieces of patches that are connected and laid out in a special way to tell a story. Not only does it portray a story that is put together in a certain sequence, but it also stiches the pieces of the quilt into a nice and complete narrative. A story that one can understand just by looking at the quilt spread and unfolded. Much like the making of a quilt that has a story to tell, a Product Digital Quilt will tell the story of a product. The Digital Product Quilt replaces the conventional way of telling a product story. The traditional product story is a method that is serially connecting multiple product life cycle silos together.

In this study we consider the coordinated exploration of an unfamiliar Martian landscape by a swarm of small autonomous rovers, called Swarmies, simulated in a distributed setting. With a sustainable program of return missions to and from Mars in mind, the goal of said exploration is to efficiently prospect the terrain for water meant to be gathered and then utilized in the production of rocket fuel. The rovers are tasked with relaying relevant data to a home base that is responsible for maintaining a mining schedule for an arbitrarily large group of rovers extracting water-rich regolith. For this reason, it is crucial that the participants maintain a wireless connection with one another and with the base throughout the entire process. We describe the architecture of our simulation which is composed of HLA-compliant components that are visualized via the Distributed Observer Network tool developed by NASA.

In this paper, we address the thermal management issues which limit the lifespan, specific power and overall efficiency of an air-cooled rotary Wankel engine used in Unmanned Air Vehicles (UAVs). Our goal is to eliminate the hot spots and reduce the temperature gradients in the engine housing and side plates by aggressive heat spreading using heat pipes. We demonstrate by simulation that, for a specific power requirement, with heat spreading and more effective heat dissipation, thermal stress and distortion can be significantly reduced, even with air cooling. The maximum temperature drop was substantial, from 231°C to 129°C. The temperature difference (measure of temperature uniformity) decreased by 8.8 times (from 159°C to 18°C) for a typical UAV engine. Our heat spreaders would not change the frontal area of the engine and should have a negligible impact on the installed weight of the propulsion assembly.

Laminar burning velocity (LBV) measurements are reported for promising high-performance fuels selected as drop-in transportation fuels to automotive grade gasoline as part of the United States Department of Energy’s Co-Optimization of Fuels and Engines Initiative (Co-Optima). LBV measurements were conducted for ethanol, methyl acetate, and 2-methylfuran with synthetic air (79.0 % N2 and 21.0 % O2 by volume) within a constant-volume spherical combustion rig. Mixture initial temperature was fixed at 428±4 K, with the corresponding initial pressure of 1.00±0.02 atm. Current LBV of ethanol is in good agreement with literature data. LBV of ethanol and 2-methylfuran showed similar values over the range of equivalence ratios, while methyl acetate exhibited an LBV significantly lower over the range of tested equivalence ratios. The maximum laminar burning velocity occurred at slightly richer equivalence ratio from the stoichiometric value for all fuels tested.

As an engineering approach of balanced complexity and accuracy, the Generalized Incremental Stress-State dependent damage Model (GISSMO) in LS-DYNA® has now been widely adopted by the automotive industry to predict metallic materials’ fracture occurrences in both forming and crashworthiness simulations. Calibration of the nominal GISSMO is typically based on material characterization data along a certain representative material orientation. Nevertheless, many rolled or extruded metallic materials, such as advanced high-strength steel (AHSS) sheets, exhibit accentuated anisotropic fracture behavior, even though, notably, some of these materials show comparatively weak anisotropic plasticity in the meantime. Accordingly, in this work, the deformation and fracture behavior of a selected AHSS grade, Q&P980 steel, was first characterized based on a series of mechanical experiments under simple shear, uniaxial tension, plane strain, and equi-biaxial tension conditions.

A comprehensive plasticity and fracture model was built for metal sheets with application to metal sheet forming and vehicle crash simulations. The combined Bai-Wierzbicki (BW [1]) and CPB06ex2 [2] (or Yld2000-2D [3]) anisotropic plasticity model was further extended to consider elevated temperature effects in additional to the effect of multiaxial stress states. A fully modularized framework was established to combine isotropic, kinematic, and cross hardening behaviors under non-linear loading conditions. The all strain based modified Mohr-Coulomb (eMMC) fracture model was used to consider material anisotropy and nonlinear strain path. The model has been implemented into Abaqus/Explicit as a user material subroutine (VUMAT). Test results on advanced high strength steels, aluminum alloy sheets and magnesium alloy sheets are used to validate the modeling and testing methodologies. Very good correlation was observed between experimental and simulation results.

A fully modularized framework was established to combine isotropic, kinematic, and cross hardening behaviors under non-monotonic loading conditions for advanced high strength steels. Experiments under the following types of non-proportional loading conditions were conducted, 1) uniaxial tension-compression-tension/compression-tension-compression full cycle reversal loading, 2) uniaxial reversal loading with multiple cycles, and 3) reversal shear. The calibrated new model is decoupled between isotropic and kinematic hardening behaviors, and independent on both anisotropic yield criterion and fracture model. Nine materials were calibrated using the model, include: DP590, DP600, DP780, TRIP780, DP980LY, QP980, AK Steel DP980, TBF1180, and AK Steel DP1180. Good correlation was observed between experimental and modeled results.