Search Results

This study was conducted to develop and validate a multidimensional measure of shift quality as perceived by drivers during kick-down shift events for automatic transmission vehicles. As part of the first study, a survey was conducted among common drivers to identify primary factors used to describe subjective gear-shifting qualities. A factor analysis on the survey data revealed four semantic subdimensions. These subdimensions include responsiveness, smoothness, unperceivable, and strength. Based on the four descriptive terms, a measure with semantic scales on each subdimension was developed and used in an experiment as the second study. Twelve participants drove and evaluated five vehicles with different gear shifting patterns. Participants were asked to make kick-down events with two different driving intentions (mild vs. sporty) across three different speeds on actual roadway (local streets and highway).

This paper presents results of a study conducted to compare driving behavior and performance of drivers in two different fixed-base driving simulators (namely, FAAC and STI) while performing a same set of distracting tasks under geometrically similar freeway and traffic conditions. The FAAC simulator had a wider three-screen road view with steering feedback as compared to the STI simulator which had a single screen and narrower road view and had no steering feedback. Twenty four subjects (12 younger and 12 mature) drove each simulator and were asked to perform a set of nine different tasks involving different distracting elements such as, using a cell phone, operating the car radio, retrieving and selecting a map from map pocket in the driver's door, collecting coins to pay toll, etc.

Security is a huge concern in VANETs (Vehicular Ad hoc NETworks) since the information being conveyed may affect life-or-death decisions. One of the security concerns is the Sybil Attack. This attack attempts to create multiple identities to disrupt or control the network. A malicious node utilizing the Sybil Attack in VANETs can disrupt the network in various ways. It can create a large number of Sybil nodes to intervene in message forwarding, potentially causing a massive pileup and great loss of life. A malicious node can also use the Sybil Attack to create illusions of traffic congestions, getting other drivers to take alternate routes and leaving a clear path for the malicious node to its destination. In this paper, we discuss several defense strategies for the Sybil Attack in VANETs.

Although computer models for vehicle and sub-system performance simulations have been developed and used extensively in the past several decades, there is currently a need to enhance the overall availability of these types of tools. Increasing demands on vehicle performance targets have intensified the need to obtain rapid feedback on the effects of vehicle modifications throughout the entire development cycle. At the same time, evolution of the PC and development of Web-based applications have contributed to the availability, accessibility, and user-friendliness of sophisticated computer analysis. Web engineering is an ideal approach in supporting globalization and is a cost-effective design-analysis integration business strategy. There is little doubt that this new approach will have positive impacts on product cost, quality, and development cycle time. This paper will show how Microsoft Excel and the Web can be powerful and effective tools in the development process.

This paper describes a research project currently in-progress to develop a parametric model of a vehicle for use in early design stages of a new vehicle program. The model requires key input parameters to define the kind of new vehicle to be designed — in terms of details such as its intended driver/user population, vehicle type (e.g. 2-box, 3-box designs), and some key exterior and interior dimensions related to its size and proportions. The model computes and graphically displays interior package, ergonomics zones for driver controls and displays, and field of views through window openings. It also allows importing or inputting and superimposing and manipulating exterior surfaces created by a designer to assess compatibility between the interior occupant package and the vehicle exterior.

It is well understood that driver's steering input strongly affects lateral vehicle dynamics and excessive steering command may result in unstable vehicle motion. In a certain driving condition, it is possible for a skilled driver to prevent vehicle rollover with better perceptive capability of judging conditions and responding faster with smooth compensatory actions. This paper investigates the possibility of using active steering and wheel torque control to assist drivers in avoiding vehicle rollovers in emergency situations. The effectiveness of steering control alone and combination of steering/wheel torque control in recovery from unstable vehicle roll condition was demonstrated through simulation of both low and high vehicle speeds.

This paper presents results of a study conducted to determine differences in older (over age 55) and younger (under age 35), male and female drivers while entering and exiting vehicles with three different body styles - namely, a large sedan, a minivan and a full-size pick-up truck. Thirty-six drivers (males and females, ages 25 to 89 years) who participated in this study were first measured for their anthropometric, strength and body flexibility measures relevant to the entry/exit tasks. They were asked to first get in each vehicle and adjust their preferred seating position. Then, they were asked to get in the vehicle and their entry time was measured. Their entry maneuver was also video taped and they were asked to rate the level of ease/difficulty (using a 5-point scale) in entering. Similar procedure and measurements were conducted during their exit from each vehicle.

With the increasing presence of the Internet in today's applications, ranging from legacy enterprise systems to handheld devices and home appliances, there is an increasing need for a generic middleware that can enable the interoperability between heterogeneous systems. In the specific case of in-vehicle networks, a generic middleware would enable the vehicle/driver to interact with a diversity of applications, including legacy enterprise systems, other embedded systems and wireless ad-hoc and ubiquitous applications. This paper is the result of an initial investigation into the requirements for such a middleware, and possible directions to be taken for its implementation.

Always for means of a measurement of the torque of car units are made great requirements. In the paper presented the opportunities of more exact measurement of the torque using the microprocessor meter and the dynamics of an offered meter are analyzed. The use of the given torque meter will allow improving technical, economic, operational and other properties of car stands.

This study investigated the effects of three navigation system human-machine interfaces (HMIs) on driver eye-glance behavior, navigational errors, and subjective assessments. Thirty-six drivers drove an unfamiliar 3-segment route in downtown Detroit. HMIs were 2D or 3D (level-of-detail) electronic map display + standard voice prompts, or 3D map-display augmented by photorealistic images + landmark-enhanced voice prompts. Participants drove the same three route segments in order but were assigned a different HMI condition/segment in a 3-period/3-treatment crossover experimental design. Results indicate that drivers’ visual attention using the advanced navigation systems HMIs were within US Department of Transportation recommended visual distraction limits. More turns missed in the first route segment, regardless of HMI, were attributable to greater route complexity and a late-onset voice prompt. Participant’s ratings of HMIs were influenced by the context in which that HMI was used.

The problem of increasing the accuracy of determining the torque and the load angle of the permanent magnet synchronous motor of an electric traction drive to the predicted level (2.5...3)% of the full-scale error is solved by an indirect method. We considered the algorithms for calculating the generalized current and voltage of the electric motor, the total power, the instantaneous values of the power factor, and the sine of the phase angle between the first harmonics of voltages and currents. We determined the requirements for the accuracy of determining these values at the level of 1% of the full-scale error. We considered the algorithms for determining the total instantaneous power losses by the indirect method at the predicted level (15...20)% of the full-scale error with the efficiency of the motor (90...95)%.

Seat comfort is a highly subjective attribute and depends on a wide range of factors, but the successful prediction of seat comfort from a group of relevant variables can hold the promise of eliminating the need for time-consuming subjective evaluations during the early stages of seat cushion selection and development. This research presents the subjective seat comfort data of a group of 30 participants using a controlled range of seat foam samples, and attempts to correlate this attribute with a) the anthropometric and demographic characteristics of the participants, b) the objective pressure distribution at the body-seat interface and c) properties of the various foam samples that were used for the test.

In this paper, a new algorithm, named Nonlinear Optimization Method (NOM) has been mathematically and computationally developed for several geometric elements. The initial condition of the NOM is obtained by LSM, then the minimum zone is optimized in accordance with tolerancing principles in ANSI Y14.5.1M. The results are verified to be the Minimum Zone Evaluation (MZE) for the inspected geometric features. The algorithm, together with its computational realization programs, are proved to be considerably reliable and robust for practical applications.

We present research in progress to develop and implement a transportable instrumentation package (TIP) to collect driver data in a vehicle. The overall objective of the project is to investigate the symbiotic relationship between humans and their vehicles. We first describe the state-of-art technologies to build the components of TIP that meet the criteria of ease of installation, minimal interference with driving, and sufficient signals to monitor driver state and condition. This method is a viable alternative to current practice which is to first develop a fully instrumented test vehicle, often at great expense, and use it to collect data from each participant as he/she drives a prescribed route. Another practice, as for example currently being used in the SHRP-2 naturalistic driving study, is to install the appropriate instrumentation for data collection in each individual's vehicle, often requiring several hours.

With recent advances in microprocessors and data storage technologies, vehicle users can now bring or access large amounts of data in vehicles for purposes such as communication (e.g. e-mail, phone books), entertainment (e.g. music and video files), browsing and searching for information (e.g. on-board computers and internet). The challenge for the vehicle designer is how to design data displays and retrieval methods to allow data search and manipulation tasks by managing driver workload at safe acceptable levels. This paper presents a data retrieval menu system developed to assess levels of screens (depth of menu) that may be needed to select required information when a vehicle is equipped with the capability to access audio files, cell phone, PDA, e-mail and “On-star” type functions.

In military vehicles reliability can sometimes be a more important issue than cost. With that in perspective, this paper discusses the load availability and reliability issues in automotive multiplexed wiring harness systems, which are potentially useful in the military, and compares the same with a regular non-multiplexed system. For that purpose, a figure of merit or metric is introduced, and the load availability is described in terms of this metric, which depends on the architecture chosen.

Controller Area Network (CAN), the de facto standard for in-vehicle networks, has insufficient security features and thus is inherently vulnerable to various attacks. To protect CAN bus from attacks, intrusion detection systems (IDSs) based on advanced deep learning methods, such as Convolutional Neural Network (CNN) and Recurrent Neural Network (RNN), have been proposed to detect intrusions. However, those models generally introduce high latency, require considerable memory space, and often result in high energy consumption. To accelerate intrusion detection and also reduce memory requests, we exploit the use of Binarized Neural Network (BNN) and hardware-based acceleration for intrusion detection in in-vehicle networks. As BNN uses binary values for activations and weights rather than full precision values, it usually results in faster computation, smaller memory cost, and lower energy consumption than full precision models.

Owing to their weight saving potential and improved flexural stiffness, metal-polymer-metal sandwich laminates are finding increasing applications in recent years. Increased use of such laminates for automotive body panels and structures requires not only a better understanding of their mechanical behavior, but also their formability characteristics. This study focuses on the formability of a metal–polymer-metal sandwich laminate that consists of AA5182 aluminum alloy as the outer skin layers and polypropylene (PP) as the inner core. The forming limit curves of Al/PP/Al sandwich laminates are determined using finite element simulations of Nakazima test specimens. The numerical model is validated by comparing the simulated results with published experimental results. Strain paths for different specimen widths are recorded.

This study presents a methodology for comparative analysis of seat and suspension parameters on a system level to achieve minimum occupant head displacement and acceleration, thereby improving occupant ride comfort. A lumped-parameter full-vehicle ride model with seat structures, seat cushions and five occupants has been used. Two different vehicle masses are considered. A low amplitude pulse signal is provided as the road disturbance input. The peak vertical displacement and acceleration of the occupant’s head due to the road disturbance are determined and used as measures of ride comfort. Using a design of experiments approach, the most critical seat cushion, seat structure and suspension parameters and their interactions affecting the occupant head displacement and acceleration are determined. An optimum combination of parameters to achieve minimum peak vertical displacement and acceleration of the occupant’s head is identified using a response surface methodology.

The diesel engine with direct injection of hydrogen gas has clear advantages over the hydrogen engine with forced ignition of a hydrogen-air mixture. Despite of this, the concept of hydrogen-diesel engine has not investigated until now. In the paper, a detailed study of the working process of hydrogen-diesel engine carried out for the first time. Based on the results of the experimental studies and mathematical modeling, it has established that the behavior of thermo-physical processes in the combustion chamber of hydrogen-diesel engine, in a number of cases, differs fundamentally from the processes that take place in the conventional diesel engines. There have been identified the reasons for their difference and determined the values of the operating cycle parameters of hydrogen diesel engine, which provide the optimal correlation between the indicator values and the environmental performance.