Search Results

The MX-2 neutral buoyancy space suit analogue has been designed and developed at the University of Maryland to facilitate analysis of space suit components and assessment of the benefits of advanced space suit technologies, The MX-2 replicates the salient features of microgravity pressure suits, including the induced joint torques, visual, auditory and thermal environments, and microgravity through the use of neutral buoyancy simulation. In this paper, design upgrades and recent operations of the suit are outlined, including many experiments and tests of advanced space suit technologies, This paper focuses on the work done using the MX-2 to implement and investigate various advanced controls and displays within the suit, to enhance crewmember situational awareness and effectiveness, and enable human-robotic interaction.

Recent free piston engine research reported in the literature has included development efforts for single and dual cylinder devices through both simulation and prototype operation. A single cylinder, spring opposed, oscillating linear engine and alternator (OLEA) is a suitable architecture for application as a steady state generator. Such a device could be tuned and optimized for peak efficiency and nominal power at unthrottled operation. One of the significant challenges facing researchers is startup of the engine. It could be achieved by operating the alternator in a motoring mode according to the natural system resonant frequency, effectively bouncing the translator between the spring and cylinder, increasing stroke until sufficient compression is reached to allow introduction of fuel and initiation of combustion. To study the natural resonance of the OLEA, a numeric model has been built to simulate multiple cycles of operation.

The free piston linear engine has the potential to achieve high efficiency and might serve as a viable platform for robust implementation of low temperature combustion schemes (such as homogeneous charge compression ignition - HCCI) due to its ability to vary compression and stroke in response to cylinder and load events. A major challenge is control of the translator motion. Lack of geometric constraint on the piston leads to uncertainty about its top dead center position and timing. While combustion control depends on knowledge of the piston motion, the combustion event also affects the motion profile of the piston. To advance understanding of this coupled system, a numeric model was developed to simulate multiple cycles of a dual cylinder, spring assisted, 2-stroke HCCI, free piston linear engine generator.

The Pride of Maryland is a single seat solar powered trans-continental race car designed and built by engineering students at the University of Maryland. The car competed in G.M. Sunrayce USA, placing third, and has gone on to compete in the World Solar Challenge. This paper outlines the three general areas of design and development for the solar vehicle: aerodynamic, electrical, and mechanical. An exercise in high efficiency, the Pride of Maryland has been extremely successful as both a race car and as an educational tool for training student engineers in “real world” problems.

Smoke detection experiments were conducted in the Microgravity Science Glovebox (MSG) on the International Space Station (ISS) during Expedition 15 in an experiment entitled Smoke Aerosol Measurement Experiment (SAME). The preliminary results from these experiments are presented. In order to simulate detection of a prefire overheated-material event, samples of five different materials were heated to temperatures below the ignition point. The smoke generation conditions were controlled to provide repeatable sample surface temperatures and air flow conditions. The smoke properties were measured using particulate aerosol diagnostics that measure different moments of the size distribution. These statistics were combined to determine the count mean diameter which can be used to describe the overall smoke distribution.

Initial results are reported for the effects of electrical body forces on heat transfer performance of an instrumented spray cooling experiment. Heat transfer performance is documented for ranges of electrode voltage, spray volume flow rate, and heater power level using a Thick Film Resistor heater. The heat transfer coefficient increases with increased spray flow rate, and also increases somewhat versus heat flux. Without the electrical body forces, different brass and PVC spray nozzles show significant variation in spray cooling performance (order of ±5-15%) whenever the nozzle is realigned. Changing the nozzle-to-heater spacing results in similar performance variations. Initial Kelvin force electrode designs show no improvement in heat transfer performance using FC-72, while a Coulomb force electrode geometry and a second-generation Kelvin force electrode design both show modest but consistent improvements (order of 10% in heat flux; order of 5% for Nusselt number) using HFE-7000.

The key to overcoming Low Temperature Combustion (LTC) load range limitations is based on suitable control over the thermo-chemical properties of the in-cylinder charge. The proposed alternative to achieve the required control of LTC is the use of two separate fuel streams to regulate timing and heat release at specific operational points, where the secondary fuel, with different autoignition characteristics, is a reformed product of the primary fuel in the tank. It is proposed in this paper that the secondary fuel is produced using Thermo-Chemical Recuperation (TCR) with steam/fuel reforming. The steam/fuel mixture is heated by sensible heat from the engine exhaust gases in the recuperative reformer, where the original hydrocarbon reacts with water to form a hydrogen rich gas mixture. An equilibrium model developed by Gas Technology Institute (GTI) for n-heptane steam reforming was applied to estimate reformed fuel composition at different reforming temperatures.

This paper presents results from a smoke detection experiment entitled Smoke Aerosol Measurement Experiment (SAME) which was conducted in the Microgravity Science Glovebox on the International Space Station (ISS) during Expedition 15. Five different materials representative of those found in spacecraft were pyrolyzed at temperatures below the ignition point with conditions controlled to provide repeatable sample surface temperatures and air flow conditions. The sample materials were Teflon®, Kapton®, cellulose, silicone rubber and dibutylphthalate. The transport time from the smoke source to the detector was simulated by holding the smoke in an aging chamber for times ranging from 10 to1800 seconds. Smoke particle samples were collected on Transmission Electron Microscope (TEM) grids for post-flight analysis.

A Capillary Pumped Loop (CPL) is an advanced two-phase heat transport device which utilizes capillary forces developed within porous wicks to move a working fluid. The advantage this system has over conventional thermal management systems is its ability to transfer large heat loads over long distances at a controlled temperature. Extensive ground testing and two flight experiments have been performed over the past decade which have demonstrated the potential of the CPL as a reliable and versatile thermal control system for space applications. While the performance of CPL's as “black boxes” is now well understood, the internal thermo-fluid dynamics in a CPL are poorly known due to the difficulty of taking internal measurements. In order to visualize transient thermohydraulic processes occurring inside an evaporator, a see-through capillary evaporator was built and tested at NASA's Goddard Space Flight Center.

Results from the research projects sponsored by General Motors, Motor Vehicle Fire Research Institute and National Highway Traffic Safety Administration are discussed. In the projects, thermophysical and fire properties of engine compartment fluids and polymer parts of the vehicle were quantified. Burning behaviors of the actual vehicle parts and front and rear crashed vehicle were also examined. Penetration of flames into the passenger compartment was the most critical stage in vehicle crash fire tests. Pain, 2nd and 3rd degree burns, flashover, toxicity, and lethality followed in that order very shortly after the flame penetration. The flame penetration into the passenger compartment from the engine compartment fires in front vehicle crashes was significantly longer (10 to 24 minutes post ignition) than from gasoline pool fires under the vehicle (0.5 to 3.0 minutes post ignition).

Machine learning algorithms are effective tools to reduce the number of engine dynamometer tests during internal combustion engine development and/or optimization. This paper provides a case study of using such a statistical algorithm to characterize the heat transfer from the combustion chamber to the environment during combustion and during the entire engine cycle. The data for building the machine learning model came from a single cylinder compression ignition engine (13.3 compression ratio) that was converted to natural-gas port fuel injection spark-ignition operation. Engine dynamometer tests investigated several spark timings, equivalence ratios, and engine speeds, which were also used as model inputs. While building the model it was found that adding the intake pressure as another model input improved model efficiency.

A mathematical model of combustion process in a diesel engine has been developed according to the theory of the chain reactions for the higher hydrocarbon compounds. The instantaneous rates of fuel vaporization and combustion are defined by the current values of temperature, pressure, concentration of fuel vapors, overall diffusion rate, fuel injection rate, and mean fuel droplet size in terms of the SMD. Numerical experiments have been carried out for investigating the interdependencies between various combustion-related parameters. Specifically, the effect of fuel droplet size (in terms of SMD) on the subsequent combustion parameters, such as, pressure, temperature, thermodynamic properties of air/gas mixture, heat transfer, fuel vaporization, combustion rate, current A/F ratio, gas mixture composition have been investigating. In addition, the integral indicator parameters of the engine, such as the mean indicated pressure, peak pressure, compression pressure have been analyzed.

This paper examines the energy pathways of a 29cc air-cooled two-stroke engine operating on natural gas with different exhaust geometries. The engine was operated at wide-open-throttle at a constant speed of 5400 RPM with ignition adjusted to yield maximum brake torque while the fueling was adjusted to examine both rich and lean combustion. The exhaust configurations examined included an off-the-shelf (OTS) model and two other custom models designed on Helmholtz resonance theory. The custom designs included both single and multi-cone features. Out of the three exhaust systems tested, the model with maximum trapping efficiency showed a higher overall efficiency due to lower fuel short-circuiting and heat transfer. The heat transfer rate was shown to be 10% lower on the new designs relative to OTS model.

On- and off-road heavy-duty diesel engines modified to spark-ignition natural gas operation can reduce U.S. dependence on imported oil and enhance national energy security. Engine conversion can be achieved through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. This paper investigated combustion characteristics and engine performance at several lean-burn operating conditions that changed spark timing, mixture equivalence ratio, and engine speed, using methane as NG surrogate.

Heavy-duty diesel (HDD) engines are the primary propulsion source for most heavy-duty vehicle freight movement and have been equipped with an array of aftertreatment devices to comply with more stringent emissions regulations. In light of concerns about the transportation sector's influence on climate change, legislators are introducing requirements calling for significant reductions in fuel consumption and thereby, greenhouse gas (GHG) emission over the coming decades. Advanced engine concepts and technologies will be needed to boost engine efficiencies. However, increasing the engine's efficiency may result in a reduction in thermal energy of the exhaust gas, thus contributing to lower exhaust temperature, potentially affecting aftertreatment activity, and consequently rate of regulated pollutants. This study investigates the possible utilization of waste heat recovered from a HDD engine as a means to offset fuel penalty incurred during thermal management of SCR system.

The control and design optimization of a Free Piston Engine Generator (FPEG) has been found to be difficult as each independent variable changes the piston dynamics with respect to time. These dynamics, in turn, alter the generator and engine response to other governing variables. As a result, the FPEG system requires an energy balance control algorithm such that the cumulative energy delivered by the engine is equal to the cumulative energy taken by the generator for stable operation. The main objective of this control algorithm is to match the power generated by the engine to the power demanded by the generator. In a conventional crankshaft engine, this energy balance control is similar to the use of a governor and a flywheel to control the rotational speed. In general, if the generator consumes more energy in a cycle than the engine provides, the system moves towards a stall.

This publication covers the development process of a thermal model within a complete longitudinal vehicle simulation. Therefore a dynamic/forward simulation within MATLAB Simulink is used. The modeling of the heat transport in the cooling circuit and the lubrication system as well as the heat input by the internal combustion engine is the focus of research. In the first part various possible numerical solution methods for the heat transport model are analyzed and evaluated with regard to the accuracy of the system description and real time capability. The latter is important as functionalities should be able to be subsequently implemented in an engine control unit. In addition, a method for the modeling of the heat input of the internal combustion engine is evaluated. Finally, a validation of the heat transport and heat input model is performed, using a two-cylinder motorcycle.

Within the automotive sector, the hybridization of the powertrain is well investigated and first announcements about mass production start dates have been made. Studies have shown that improvements regarding fuel economy and emission are possible. This potential and additional positive effects regarding driving performance should also be gained for the power-sport sector, even though very few investigations have been performed for this vehicle class. Though the requirements for a power-sport drivetrain differ from that of the automobile sector due to the high demand on the transient behavior, intense investigations have been started. The use of a complete vehicle simulation during the development of a hybrid vehicle is advantageous in the early phase and in the pre series calibration phase. The foreground topic for the simulation of a conventional powertrain is the power and torque distribution.