Search Results

Electric mobility is an emerging mode of transportation, causing rapid growth of battery pack usage in electric vehicles. These battery packs were limited working life to be used in electric Vehicles. In addition, the disposal is becoming as a major threat to an environment. So, there is a need to increase the working life of battery pack used in electric vehicles to reduce the burden on the environment. In this regard, this paper is focused on studying the life cycle estimation of the battery pack. Battery pack degradation was observed through its self-discharge pattern and also due to the urge to increase the rate of charging. This research study was focused on understanding the degradation rate due to self-discharge and also due to fast charging patterns in battery packs. Estimation of self-discharge is depending on voltage, time and state of charge of the battery pack. Simulation analysis will carry out to evaluate state of charge analysis of the electric vehicle battery pack.

The main objective of the study is to design and analyze casing and supports of a transmission system for an electric vehicle. The system comprises of motors as the power source, constant mesh gear box coupled with limited slip differential as the power transmitting source. The space occupied by the transmission system is a foremost constraint in designing the system. The wear and tear in the system is caused by the gear meshing process and transmission error which lead to failure of the transmission system. This internal excitation also produces a dynamic mesh force, which is transmitted to the casing and mounts through shafts and bearings. In order to overcome such issues in a transmission system, a gear box casing, differential mounts and motor mounts have been designed by the use of CAD-modeling software “SOLIDWORKS”. The designs were imported to FEA software “ANSYS” for carrying out static structural analysis.

The infliction of rigorous emission norms across the world has made the automobile industry to focus and dwell upon researches to reduce the emissions from internal combustion engines, namely diesel engines. Variation in fuel injection timing has better influence on reduction of engine exhaust emissions. This papers deals with the variation of fuel injection timing along with fuel injection pressure numerically on a 4 stroke, single cylinder, and direct injection diesel engine running at full load condition using CONVERGE CFD tool. As the piston and bowl geometry considered in this work is symmetric, only 60 degree sector of the piston cylinder assembly is considered for numerical simulation over complete 360 degree model.

Thermal management is one of the most challenging and innovative aspects of the automotive industry. The efficiency of the vehicle cooling framework unequivocally relies upon the air stream through the radiator core. Significant advances in thermal management are being embraced in the field of radiator material and coolant. The radiator shouldn't be exclusively credited for the reliable cooling of the engine. There are other auto parts that play an essential role in keeping engine temperature at a manageable level. The fan-shroud assembly is an important component of the cooling system. While the fan is responsible for drawing in air, the fan shroud's job is to ensure uniform air distribution to the radiator core. By assisting airflow in the engine compartment the fan shroud helps in dismissing excess heat from the engine. This assembly also prevents the recirculation of heated air through the cooling fan.

The present work is concentrated to study the effect of varying inlet pressures on the dynamics of the suction valve obtained from a hermetic reciprocating compressor. The effect of valve functioning on the efficiency of a compressor is highly acceptable. Rather than the delivery valve, the suction valve has a significant impact on the compressor efficiency. The reed valve in a hermetic compressor is a cantilever type arrangement. The valve operates due to the pressure difference between the suction muffler and the cylinder. The numerical analysis which includes Fluid-structure interaction is used in the present study. The flow and structural domain employed in the present study are modelled with Solidworks 15.0. The fluid structure interaction analysis is a combination of ANSYS Fluent and ANSYS structural. These two are coupled with a system coupling in ANSYS Workbench 16.0. The numerical results obtained from the simulation are validated with the experimental data.

In Formula Student, the vehicle working parameters are quite disparate from that of a commercially designed vehicle. The inability of teams to incorporate the atypical running conditions in their design causes multiple unforeseen issues. One such condition where the teams fail to improvise upon is the cooling system. Due to the high performance requirement of the competition, multiple teams participating face recurring heating problems. Maximum efficiency from a combustion vehicle can only be achieved when the cooling system is designed to handle the increasing power demand. This paper brings forth a detailed study on the intricate design of the cooling system. The problem has been approached using both theoretical and simulation models. Firstly, NTU-ℇ method was used to calculate the overall heat transfer coefficient and the temperature drop through the radiator core.

The use of Hybrid Electric Vehicles (HEV) will become imperative to meet the emission challenges. HEV have two power sources-fossil fuels driven I.C. Engine and the battery based drive. Battery technologies have seen a tremendous development, and therefore HEV’s have been benefited. Even as the battery capacities have improved, maintaining and monitoring their health has been a challenge. This research paper uses open-source platform to build a BMS. The flexibility in the implementation of the system has helped in the rapid prototyping of the system. The BMS system was evaluated on a scaled-down electric toy car for its performance and sustainability. The BMS was evaluated for reverse polarity, protection against overcharge, short-circuit, deep discharge and overload on lead acid battery. It also includes temperature monitoring of the batteries. This proposed system is evaluated on the in-house HEV two-wheeler. The initial results are promising.

In a fastening system when there is a small misalignment of the holes, the holes are enlarged to align the axes and a next size fastener is used to fit the joint. But when the misalignment is large then the enlargement need to be proportionally large. In this case a bushing is press fit onto the hole to handle the fastening. If we press fit a bushing, it generates residual stresses in the panel. These residual stresses reduce the damage life of the components on which the bushings were press fit. In the aircraft engine nacelle components the damage life is very critical in various failure conditions such as fan blade out condition, wind milling and bird strike. It increases the flight time in these events. Here four different case studies were considered to study the damage life of the aircraft components made of Aluminum or composite material.

The foremost emphasis of this paper is to project the need for collecting the outlet pollutant gases from the individual vehicle which is on fleet and the need to maintain the vehicle to make the surveillance of vehicle in the fleet. The data that is collected from the vehicle was stored in the cloud and provided to the vehicle user mobile application that displays the level of pollutant. With the help of pollutant level the user may be aware of the maintenance or the change in vehicle filling station, which will reduce the overall level of pollutant of the vehicle. The data that is uploaded in the cloud will be used by the regional transport office to keep track of the vehicle user.

At present, the emissions from an internal combustion engine exhaust is reduced by exhaust after treatment devices. However, after treatment devices like SCR which is used to control NOx, results in additional weight, high costs and rejects toxic gases like ammonia etc. To overcome this problem, a new combustion technique should be developed to improve the primary combustion processes inside the combustion chamber itself to reduce these exhaust gas emissions. This work presents the results of such a technique that is applicable to direct injection, Diesel engines. The technique is based on the porous medium combustion (PMC) technology, which is developed for steady state household and industrial combustion processes. Based on the adiabatic combustion in porous medium (PM), a porous medium in engine piston as a concept is proposed here to achieve improved combustion efficiency and low emissions. Using a commercial code CONVERGE the entire cycle is simulated and presented here.

A study of an aerofoil structure used for automotive body design is being conducted and an experiment has been performed to determine the lift and drag forces produced by it by varying its Angle of Attack. The NACA0018 and NACA0015 aerofoil with a chord length of 16 cm were used for this study. Then an analysis was done with the help of (CFD) computational fluid dynamics. The results obtained by CFD analysis where compared by the experimental results which was performed on wind tunnel using NACA0018 aerofoil. The results are then presented graphically, showing pressure and velocity distributions lift and drag coefficients for the different cases which will be useful for design of automotive body structures.

The present world persists with a twin crisis of energy consumption and the environmental degradation. Finding a compromise between them provides a breakthrough in the research in energy containments of the engine attachments. Oil pump has role of providing the transmission of oil to other engine parts and acts as the coolant for the moving parts. Conventional oil pump with pressure relief valve is its loss lot of energy in oil re-circulation due to the discharge effect. On contrary, the variable displacement oil pump has an effect on reduction of oil pressure using eccentric ring without having any compromise with the energy consumption. This paper proposes model and experimental methodology of a variable displacement Gerotor oil pump for lubricating the internal combustion engine. This particular unit is performed extremely in terms of rotational speed, delivery pressure and displacement variation.

Agriculture is a backbone of country’s economy. To increase the crop production efficiency weeds are to be removed. The present weeding machines are different in dimension which may not be suited to small and medium field farmers, due cost effectiveness and dimensions. This work presents the development of sugarcane weed remover (SWR) and its performance investigation to improve the weed removal rate. The SWR is an application specific machine, it consists of single cylinder air cooled gasoline engine, blade assembly and transmission system. In order to improve SWR efficiency different blade profiles are theoretically analysed. The optimised blade profile is employed in the weed remover which offers fuel consumption of 0.11 g/(KW.h). The SWR on-field experience confirmed that the field capacity and efficiency in weeding is 0.0025 ha/hr and 60% respectively.

A model for Hybrid electric vehicle power train with parallel hybrid braking system has been constructed. The hybrid vehicle utilized is based on integrated motor assist power train developed by Honda co utilized in Honda Insight car. The model is implemented using empirical formulation and power control schemes. A power control strategy based on throttle position (% throttle) and brake pedal position (% braking) is used. It incorporates the parallel hybrid braking system for the hybrid electric vehicle. The model allows for real time evaluation of wide range of parameters in vehicle operation as HEV without parallel hybrid braking system (PHBS) and with PHBS. Due to regenerative braking the structure design and control of braking system for HEV is different from conventional vehicle. The PHBS is the good option to provide safety of the vehicle and simultaneously recover reasonable amount of braking energy.

Though high thermal conductivity polymer composites are prepared based on the thermal requirements, the effectiveness and overall heat transfer performance of the radiators have to be addressed comprehensively to validate the concerned efforts taken to prepare the high thermal conductivity polymer composites. In this article, theoretical analysis on the thermal performance of the cross flow type heat exchanger under convection is performed only by concentrating on the term thermal conductivity of the material. Micro channel based geometry is extracted from the given heat exchanger problem to reduce the complexities of simulation. The term cooling system performance index (CSPI) is used to achieve the expected targets in the present investigation. For shorter fins, the effect of thermal conductivity on the cooling system performance index under lower Reynolds number is insignificant.

The Exhaust Noise is one of the major noise pollutants. It is well-known that for higher noise reduction, the engine has to bear high back pressure. For a race car, back-pressure plays a major role in engine's performance characteristics. For a given condition of engine rpm & load, conventional muffler has a fixed value of back-pressure and noise attenuation. Better acceleration requires low back-pressure, but the exhaust noise should also be less than the required (Norm) value (110 dBA). This contradicting condition is achieved here by using a ‘Butterfly Valve’ in this novel exhaust muffler. The butterfly valve assumes 2 positions i.e. fully open & fully closed. When the valve is fully closed, the noise reduction will be higher, but the back-pressure will also shoot up. When open, noise reduction will be less and so the back-pressure. So, when better performance is required, the valve is opened and back-pressure is reduced. The muffler is designed for a 4 cylinder 600 cc engine.

For zero tail pipe emission transportation, fuel cell technology is the best available option for replacing commercial IC engines. Worldwide lot of research work is going on in development of fuel cell vehicles. This work deals with the virtual development of system architecture for hybrid electric - fuel cell light commercial vehicle. The goal of this research work is to virtually design, model and convert an existing LCV model in to a hybrid electric fuel cell vehicle for the same performance and better efficiencies with zero tail pipe emissions. A unique fuel cell management system is developed and used for obtaining better efficiencies. A mathematical model of the vehicle is developed using GT-Drive which tracks the energy flow and fuel usage within the vehicle drivetrain. The vehicle is tested on chassis dynamometer to provide data for validation of the mathematical model. Model results and vehicle data show good correlation when validated.

The paper deals with the simulation of a Light Commercial Vehicle (LCV) using vehicle performance algorithms. This method speeds up the product development process. Also by using these kind of methodology in vehicle simulation there is much noticeable reduction in cost of testing. The simulation model is used for parametric studies of the vehicle and also to attain objectives such as to optimize transmission ratio, full load acceleration, maximum tractive force, gradient performance, fuel consumption and the exhaust emission. In this case study, simulation model of a CNG, LCV is used to analyze the performances similar to that done in a chassis dynamometer. The simulation leads to the prediction and evaluation of various parameters such as fuel consumption, exhaust emissions, full load acceleration, gradient performance & maximum tractive effort for Indian Driving Cycle.

In present commercial vehicles, the cranking torque required for a heavy duty compression ignition engine is very high. This results in higher durability and reliability requirement of cranking system components and also makes it cumbersome to implement start-stop micro hybrid feature which requires more number of cranking cycles in lifetime. Hence higher capacity starter motor and battery is being used for implementing start-stop feature. However this would result in cost and packaging issues. In order to implement start-stop feature maintaining the same starter motor and battery capacity, the cranking energy demand of the engine needs to be reduced. Studies conducted shows that the major source of breakaway torque is the work done in compression stroke during a starting cycle.

The desire for higher fuel economy, improved performance and driveability expectations of customers from engines are gradually increasing along with stringent emission regulations set by the government. Many original engine manufacturing companies are prompted to consider the application of higher function variable valve actuation mechanisms in their next generation vehicles as a solution. The VVA is a generalized term used to describe any mechanism or method that can alter the shape or timing of a valve lift event within an internal combustion engine. The VVA allows lift, duration or timing (in various combinations) of the intake and/or exhaust valves to be changed while the engine is in operation. Engine designers are prompted to consider Variable Valve Actuation (VVA) system because of the inherent compromises with fixed valve events. The major goal of a VVA engine is to control the amount of air inducted into the engine which is a direct measure of torque.