Search Results

The traditional method of engine knock detection is to compare the knock intensity with a predetermined threshold. The calibration of this threshold is complex and difficult. A statistical knock detection method is proposed in this paper to reduce the effort of calibration. This method dynamically calculates the knock threshold to determine the knock event. Theoretically, this method will not only adapt to different fuels but also cope with engine aging and engine-to-engine variation without re-calibration. This method is demonstrated by modeling and evaluation using real-time engine dynamometer test data.

A practical and low cost Blind Spot Monitoring system is proposed. By using a single camera, the range and azimuth position of a vehicle in a blind spot are measured. The algorithm is based on the proposed RWA (Range Window Algorithm). The camera is installed on the door mirror and monitoring the side and rear of the host vehicle. The algorithm processes the image and identifies range and azimuth angle of the vehicle in the adjacent lane. This algorithm is applied to real situations. The 388 images including several kinds of vehicles are analyzed. The detection rate is 86% and the range accuracy is 1.6[m]. The maximum detection range is about 30[m].

Traditionally fog lamps use halogen filament light sources. With the emergence of high brightness white LEDs, it is now possible to develop automotive forward lighting systems with LED light sources. Six LEDs are shown to be sufficient for the implementation of a European fog lamp using a faceted reflector optical approach. Each reflector together with the LED light source forms a modular element. The optical parameters of two different lamp designs are compared and correlation between the simulation and prototype measurements is shown. Further, additional forward lighting functions can be implemented through the use of additional elements.

Internal combustion engines are designed to maximize power subject to meeting exhaust emission requirements and minimizing fuel consumption. Maximizing engine power and fuel economy is limited by engine knock for a given air-to-fuel charge. Therefore, the ability to detect engine knock and run the engine at its knock limit is a key for the best power and fuel economy. This paper shows inaudible knock detection ability using in-cylinder ionization signals over the entire engine speed and load map. This is especially important at high engine speed and high EGR rates. The knock detection ability is compared between three sensors: production knock (accelerometer) sensor, in-cylinder pressure and ionization sensors. The test data shows that the ionization signals can be used to detect inaudible engine knock while the conventional knock sensor cannot under some engine operational conditions.

MBT timing for an internal combustion engine is also called minimum spark timing for best torque or the spark timing for maximum brake torque. Unless engine spark timing is limited by engine knock or emission requirements at a certain operational condition, there exists an MBT timing that yields the maximum work for a given air-to-fuel mixture. Traditionally, MBT timing for a particular engine is determined by conducting a spark sweep process that requires a substantial amount of time to obtain an MBT calibration. Recently, on-line MBT timing detection schemes have been proposed based upon cylinder pressure or ionization signals using peak cylinder pressure location, 50 percent fuel mass fraction burn location, pressure ratio, and so on. Because these criteria are solely based upon data correlation and observation, both of them may change at different engine operational conditions. Therefore, calibration is still required for each MBT detection scheme.

Customer clinics and surveys have revealed the increased importance to the customer of good defrost and demist performance in their vehicle. Achieving this level of performance, within the time and cost constraints of a modern vehicle development program, places increased reliance on computational (CAE) techniques. However, this paper describes how the optimum development process should be to combine this reliance upon CAE methods with a newly developed experimental technique. This new laser Doppler velocimetry (LDV) based methodology is employed at all stages of the development process and complements the CAE techniques perfectly. The end result is optimized airflow management within the vehicle cabin – essential if good defrost and demist performance is to be achieved in a vehicle.

Low resolution fractional factorial experimental designs, used in screening, are more popular than ever due to the ever increasing costs of materials and machine time. Experimenters have to be more precise in their analysis, making every degree of freedom count. Resolution III designs are becoming more commonplace for use in screening designs. When running unsaturated resolution III designs there are extra degrees of freedom stemming from unassigned interactions. It is common practice to utilize these extra degrees of freedom to approximate error. In many cases, this common practice can over state the error and lead to erroneous results regarding factor statistical significance. Utilizing saturated resolution III designs and statistically analyzing unassigned interactions while estimating the error with replication is a method for strengthening the DOE strategy and improving the results from screening designs.

Application of Ultra Thin Wall (UTW) ceramic substrates in the catalytic converter system requires the canner and component manufacturers to better understand the root cause and physics behind substrate breakage during the canning process. For this purpose, a ceramic substrate strength study for shoebox design has been conducted within Visteon Corporation. Computer Numerical Control (CNC) machined top and bottom fixtures, with identical inner surfaces as shoebox converter upper and lower shells, were used to crush mat wrapped substrates. Thin film pressure sensor technology enables the recording of substrate surface pressure during the compression process. Shell rib, washcoat, canning speed and cell density effects on substrate failure have been experimentally investigated. The development of a mathematical model helps to identify a better indicator to evaluate the substrate strength in the canning process and establish the strength for uncoated & coated substrates.

Reliable prediction of the radiated noise due to the air pressure pulsation inside air-intake manifolds (AIM) is of significant interest in the automotive industry. A practical methodology to model plastic AIMs and a prediction process to compute the radiated noise are presented in this paper. The measured pressure at the engine inlet valve of an AIM is applied as excitation on an acoustic boundary element model of the AIM in order to perform a frequency response analysis. The measured air pressure pulsation is obtained in the crank-angle domain. This pressure is read into MATLAB and transformed into the frequency domain using the fast Fourier transform. The normal modes of the structure are computed in ABAQUS and a coupled analysis in SYSNOISE is launched to couple the boundary element model and the finite element model of the structure. The computed surface vibration constitutes the excitation for an acoustic uncoupled boundary element analysis.

The present work demonstrates the application of Design of Experiments (DOE) statistical methods to the design and optimization of a hydraulic steering pump for NVH performance. DOE methods were applied to RPM-domain data to examine the effect of several different factors, as well as the interactions between these factors, on pump NVH. Whereas most DOE analyses typically consider only a single response variable, the present work considered multiple response variables. Specifically, pump NVH performance curves for several pump rotational orders over a range of shaft speeds were analyzed. Thus, it was possible to determine the effect of the factors in question over the entire speed range of pump operation, rather than a single speed or setting. Statistical methods were applied to determine which factors and interactions had a significant effect on pump NVH. These factors were used to construct an empirical mathematical prediction model for NVH performance.

Estimation and prediction of residual life and reliability are serious concerns in life cycle management for aging structures. Laboratory testing replicating fatigue loading for a typical military aircraft wing skin was undertaken. Specimens were tested until their fatigue life expended reached 100% of the component fatigue life. Then, scanning electron microscopy was used to quantify the size and location of fatigue cracks within the high stress regions of simulated fastener holes. Distributions for crack size, nearest neighbor distances, and spatial location were characterized statistically in order to estimate residual life and to provide input for life cycle management. Insights into crack initiation and growth are also provided.

An algorithm, which determines the range of a preceding vehicle by a single image, had been proposed. It uses a “Range-Window Algorithm”. Here in order to realize higher robustness and stability, the pattern matching is incorporated into the algorithm. A single camera system using this algorithm has an advantage over the high cost of stereo cameras, millimeter wave radar and non-robust mechanical scanning in some laser radars. And it also provides lateral position of the vehicle. The algorithm uses several portions of a captured image, namely windows. Each window is corresponding to a predetermined range and has the fixed physical width and height. In each window, the size and position of objects in the image are estimated through the ratio between the widths of the objects and the window, and a score is given to each object. The object having the highest score is determined as the best object. The range of the window corresponding to the best object becomes an estimated range.

The present work discusses the application of multivariate statistical methods for the analysis of NVH data. Unlike conventional statistical methods which generally consider single-value, or univariate data, multivariate methods enable the user to examine multiple response variables and their interactions simultaneously. This characteristic is particularly useful in the examination of NVH data, where multiple measurements are typically used to assess NVH performance. In this work, Principal Components Analysis (PCA) was used to examine the NVH data from a benchmarking study of hydraulic steering pumps. A total of twelve NVH measurements for each of 99 pump samples were taken. These measurements included steering pump orders and overall levels for vibration and sound pressure level at two microphone locations. Application of the PCA method made it possible to examine the entire set of data at once.

The present work demonstrates the application of Design of Experiments (DOE) statistical methods to the design and the improvement of a hydraulic steering pump noise, vibration, and harshness (NVH) performance in relief. DOE methods were applied to subjective ratings to examine the effect of several different factors, as well as the interactions between these factors on pump relief NVH. Specifically, the DOE was applied to the geometry of the cross ports on a hydraulic relief valve to improve “whistle” noise in the pump. Statistical methods were applied to determine which factors and interactions had a significant effect on pump whistle. These factors were used to produce a more robust cross port configuration reducing whistle noise. Lastly, the final configuration was experimentally verified on the test apparatus and subjectively confirmed in vehicle-level testing.

A major source of engine-off evaporative hydrocarbon emissions is fuel injector leakage. Methods and devices to relieve fuel rail pressure after key-off, and thus reduce leakage are introduced. Impact on fuel manifold re-pressurization is considered. The basic principles governing this behavior: fuel thermal expansion, fuel vapor pressure, and dissolved gasses in liquid are elaborated. Fuel pressure relief data is shown.

A coupled vibration and pressure loading procedure has been developed to perform a CAE virtual test for engine air intake manifolds. The CAE virtual test simulates the same physical test configuration and environments, such as the base acceleration vibration excitation and pressure pulsation loads, as well as temperature conditions, for design validation (DV) test of air intake manifolds. The original vibration and pressure load data, measured with respect to the engine speed rpm, are first converted to their respective vibration and pressure power spectrum density (PSD) profiles in frequency domain, based on the duty cycle specification. The final accelerated vibration excitation and pressure PSD load profiles for design validation are derived based on the key life test (KLT) duration and reliability requirements, using the equivalent fatigue damage technique.

In today's search for a better fuel economy and lower emissions, it is essential to precisely control the injected fuel quantity, as demanded by the engine load, into each of the engine cylinders. In fuel injection systems, the pressure pulsations due to the rapid opening and closing of the injectors can cause uneven injected fuel amounts between cylinders. In order to develop effective techniques to reduce these pressure pulsations, it is crucial to have a good understanding of the dynamic characteristics of such fuel injection systems. This paper presents the benefits of using simulation as a tool to analyze the dynamic behaviors of a V8 gasoline injection system. The fuel system modeling, based on a one-dimensional (1D) lumped parameter approach, has been developed in the AMESim® environment. The comparison between the simulation results and the experimental data shows good agreement in fluid transient characteristics for both time and frequency domains.

Maximum Brake Torque (MBT) timing for an internal combustion engine is the minimum advance of spark timing for best torque. Traditionally, MBT timing is an open loop feedforward control whose values are experimentally determined by conducting spark sweeps at different speed, load points and at different environmental operating conditions. Almost every calibration point needs a spark sweep to see if the engine can be operated at the MBT timing condition. If not, a certain degree of safety margin is needed to avoid pre-ignition or knock during engine operation. Open-loop spark mapping usually requires a tremendous amount of effort and time to achieve a satisfactory calibration. This paper shows that MBT timing can be achieved by regulating a composite feedback measure derived from the in-cylinder ionization signal referenced to a top dead center crank angle position. A PI (proportional and integral) controller is used to illustrate closed-loop control of MBT timing.

This paper describes the applicability of optical imaging techniques to the analysis of the scratch resistance of automotive interior plastic materials. The evaluation of so-called “finger testing” has traditionally relied upon human vision for detection of the initial scratch position. Commonly performed under uniform and defined illumination conditions, the relative contrast difference signified by whitening on a surface as determined by unaided human vision is a highly variable subjective perception; thus individual inspectors may determine the “whitening” point differently. This paper compares test data obtained from both visual and instrumental evaluation methods and discusses the advantages of optical imaging techniques for surface defect analysis.