Search Results

This paper describes the characterisation of heat transfer in a series of 11 test sections designed to represent a range of configurations seen in production exhaust systems, which is part of a larger activity aimed at the accurate modeling of heat transfer and subsequent catalyst light off in production exhaust systems comprised of similar geometries. These sections include variations in wall thickness, diameter, bend angle and radius. For each section a range of transient and steady state tests were performed on a dynamic test cell using a port injected gasoline engine. In each case a correlation between observed Reynolds number (Re) and Nusselt number (Nu) was developed. A model of the system was implemented in Matlab/Simulink in which each pipe element was split into 25 sub-elements by dividing the pipe into five both axially and radially. The modeling approach was validated using the experimental data.

Increasing the number of cold-start engine cycles which could be run in any one day would greatly improve the productivity of an engine test facility. However with the introduction of forced cooling procedures there is the inherent risk that test-to-test repeatability will be affected. Therefore an investigation into the effects caused by forced cooling on fuel consumption and the temperature distribution through the engine and fluids is essential. Testing was completed on a 2.4 litre diesel engine running a cold NEDC. The test facility utilises a basic ventilation system, which draws in external ambient air, which is forced past the engine and then drawn out of the cell. This can be supplemented with the use of a spot cooling fan. The forced cool down resulted in a much quicker cool down which was further reduced with spot cooling, in the region of 25% reduction.

This paper investigates the potential for reduced NOx emissions from the integration of thermal factors into the Diesel engine calibration process. NOx emissions from Diesel engines have been shown to be sensitive to engine operating temperature, which is directly related to the level of cooling applied to the engine, in addition to the main engine operating parameters such as injection timing and EGR ratio. Experimental engine characterization of the main engine parameters against coolant temperature set point shows that engine cooling settings can extend the feasible lower limits of fuel consumption and emissions output from Diesel engine. With the adoption of an integrated calibration methodology including engine cooling set point, NOx emissions can be improved by up to 30% at crucial high speed/load operating points seen in the NEDC drive cycle with a minor reduction in fuel economy and small increase in CO output.

A study has been undertaken to demonstrate the use and potential benefits of actively controlled coolant jets in a vehicle. Results have shown that active control of cooling jets has the potential to regulate the temperature of thermally critical areas of the cylinder head, in this case the exhaust valve bridge. In addition the temperature gradient across the head from the exhaust valves to the inlet valves is directly influenced. These capabilities offer improved control of the combustion process and enhanced durability. Furthermore the system allows heat to be rejected at much lower overall coolant flow rates than with a conventional arrangement. The technique relies on an adequate supply of coolant at a lower temperature than that within the engine and on the availability of a suitable measurement technology within the thermally critical region. Unlike passive precision cooling the active jets allow optimization of the cooling at all engine speed / load points.

Electric coolant pumps for IC engines are under development by a number of suppliers. They offer packaging and flexibility benefits to vehicle manufacturers. Their full potential will not be realised, however, unless an integrated approach is taken to the entire cooling system. The paper describes such a system comprising an advanced electric pump with the necessary flow controls and a supervisory strategy running on an automotive microprocessor. The hardware and control strategy are described together with the simulation developed to allow its calibration and validation before fitting in a B/C class European passenger car. Simulation results are presented which show the system to be controllable and responsive to deliver optimum fuel consumption, emissions and driver comfort.

More stringent legislative guidelines on emissions and fuel economy have led to an increased number of engine parameters to be optimised. Steady state engine mapping to produce an empirical engine model remains a fundamental step in this optimisation process. Recently statistical techniques such as design of experiments have been introduced to improve the efficiency of this modeling phase. Before undertaking an experimental design it is first necessary to determine the permissible envelope of the various design parameters. The importance of this limit space is two fold, firstly to ensure that the engine is not operated in regions, which may cause damage to it, and secondly so that subsequent experimentation yields test data wholly valid for the subsequent engine model. Currently this limit space is defined in a largely manual process, requiring expert input many times in the test and characterization process.

A proof-of-concept study has been undertaken to demonstrate the use and potential benefits of actively controlled coolant jets in an IC engine cooling gallery simulator. Results have shown that substantial reductions in coolant volumes are possible and that the control of the liquid/metal surface temperature can be achieved within +/- 0.2°C in response to transient heat flux conditions.