Refine Your Search

Date

Date

Topic

Topic

SAE IC Powertrain Steering Committee Bearings Data management

Search Results

Viewing 1 to 20 of 48
123Next >Last >>
Sort by published
Standard

Seals—Evaluation of Elastohydrodynamic
2000-10-09
HISTORICAL
J1002_200010
This SAE Information Report is a review of test methods that have been used to evaluate elastomeric hydrodynamic seals. The advantages and disadvantages of each method are discussed. There are ten methods total which include three suggested methods. For those interested in more detailed information on hydrodynamic sealing systems, see 2.2.
Standard

Procedure for Measuring Bore and Face Runout of Flywheels, Flywheel Housings, and Flywheel Housing Adapters
2012-06-01
CURRENT
J1033_201206
This SAE Recommended Practice applies to any internal combustion engine which can utilize SAE No. 6 thru SAE No. 00 size flywheel housing. It provides instructions for correcting flywheel housing bore runout readings which are influenced by crankshaft bearing clearance. Limits for bore and face runout are specified in the various SAE Standards and Recommended Practices covering flywheels and flywheel housings.
Standard

Overcenter Clutch Spin Test Procedure
2012-10-23
CURRENT
J1079_201210
This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.
Standard

Engine Flywheel Housings with Sealed Flanges
2012-10-23
CURRENT
J1172_201210
This SAE Recommended Practice defines flywheel housing flange configurations for applications requiring "O" ring sealing of the flange pilot bore. Table 1 and Figure 1 show dimensions that are different from those in SAE J617. All other dimensions and tolerances of SAE J617 apply.
Standard

Thrust Washers – Design and Application
2011-06-13
CURRENT
J924_201106
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

FLYWHEELS FOR SINGLE BEARING ENGINE MOUNTED POWER GENERATORS
1986-03-01
HISTORICAL
J162_198603
This SAE Recommended Practice incorporates recommended dimensions for flywheels for use with single bearing power generators in the range of 10-500 kW, operating at speeds of 1000-1800 rpm. Driving torque, fastener strength, and rotative speeds shall be consistent with good design practice.
Standard

Flywheels for Single Bearing Engine Mounted Power Generators
1988-01-31
CURRENT
J162_198801
This SAE Recommended Practice incorporates recommended dimensions for flywheels for use with single bearing power generators in the range of 10-500 kW, operating at speeds of 1000-1800 rpm. Driving torque, fastener strength, and rotative speeds shall be consistent with good design practice.
Standard

TURBOCHARGER NOMENCLATURE AND TERMINOLOGY
1979-11-01
HISTORICAL
J922_197911
This recommended practice applies to nomenclature of turbo-charger parts and terminology of performance. Modifying adjectives are omitted in some cases for the sake of simplicity. However, it is considered good practice to use such adjectives when they add to clarity and understanding.
Standard

APPLICATION GUIDE TO RADIAL LIP SEALS
1989-08-01
HISTORICAL
J946_198908
This recommended practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally-accepted information and data. The main reason for the preparation of the recommended practice is to make standard information available in one document to the users of oil seals.
Standard

APPLICATION GUIDE TO RADIAL LIP SEALS
1991-10-01
HISTORICAL
J946_199110
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
123Next >Last >>
X