Search Results

We developed a technique to measure oil film pressure distribution in engine main bearings using thin-film pressure sensors. The sensor is 7μm in thickness, and is processed on the surface of an aluminum alloy bearing. In order to increase the durability of the sensor, a layer of MoS2 and polyamide-imide was coated on thin-film sensors. This technique was applied to a 1.4L common-rail diesel engine operated at a maximum speed of 4,500r/min with a 100Nm full load, and the oil film pressure was monitored while the engine was operating. The measured pressure was compared with calculations based on hydrodynamic lubrication (HL) theory.

Using small thin-film pressure sensors deposited onto a piston skirt surface, oil-film pressure on the piston skirt surface is measured when piston slap noise is generated without affecting the surface geometry, stiffness and mass of the piston. Under a no-load firing engine condition and at low temperature, the measured oil-film pressure corresponded well to the measured acceleration of the cylinder liner, which is indicative of piston slap noise, confirming the validity of the present method. Moreover, the oil-film pressure distribution on the skirt surface was measured for different engine speeds and piston pin offsets, which enabled more insight to be provided into piston secondary motion than that by considering the effects of cylinder liner acceleration.

The spray formation and mixing processes in a direct-injection gasoline engine are examined by using a sophisticated air flow calculation model and an original spray model. The spray model for a spiral injector can evaluate the droplet size and spatial distribution under a wide range of parameters such as the initial cone angle, back pressure and injection pressure. This model also includes the droplet breakup process due to wall impingement. The arbitrary constants used in the spray model are derived theoretically without using any experimental data. Fuel vapor distributions just before ignition and combustion processes are analyzed for both homogeneous and stratified charge conditions.

In recent years, a new type of engine (Fugine) based on the colliding of pulsed supermulti-jets was proposed by us, which indicates the potential for attaining very high thermal efficiencies and also less combustion noise. A prototype engine with eight nozzles for injecting octagonal pulsed supermulti-jets, which was developed with a low-cost gasoline injector and a double piston system, showed high thermal efficiency comparable to that of diesel engines and also less combustion noise comparable to that of traditional spark-ignition gasoline engines. Another type of prototype piston-less engine having fourteen bioctagonal nozzles was also developed and test results confirmed the occurrence of combustion, albeit it was unstable. In this work, time histories of pressure were measured in the combustion chamber of the piston-less prototype engine under a cold flow condition without combustion in order to examine the compression level obtained with the colliding supermulti-jets.

In our previous papers, a new concept of a compressive combustion engine (Fugine) was proposed based on the collision of pulsed supermulti-jets, which can enclose the burned gas around the chamber center leading to an air-insulation effect and also a lower exhaust gas temperature due to high single-point compression. In order to examine the compression level and air-insulation effect as basic data for application to automobiles, aircraft, and rockets, a prototype engine based on the concept, i.e., a piston-less prototype engine with collision of bi-octagonal pulsed multi-jets from fourteen nozzles, was developed. Some combustion results [Naitoh et al. SAE paper, 2016] were recently reported. However, there was only one measurement of wall temperature and pressure in the previous report. Thus, in this paper, more experimental data for pressures and temperatures on chamber walls and exhaust temperatures, are presented for the prototype engine.

For various densities of gas jets including very light hydrogen and relatively heavy ones, the penetration length and diffusion process of a single high-speed gas fuel jet injected into air are computed by performing a large eddy simulation (LES) with fewer arbitrary constants applied for the unsteady three-dimensional compressible Navier-Stokes equation. In contrast, traditional ensemble models such as the Reynolds-averaged Navier-Stokes (RANS) equation have several arbitrary constants for fitting purposes. The cubic-interpolated pseudo-particle (CIP) method is employed for discretizing the nonlinear terms. Computations of single-component nitrogen and hydrogen jets were done under initial conditions of a fuel tank pressure of gas fuel = 10 MPa and back pressure of air = 3.5 MPa, i.e., the pressure level inside the combustion chamber after piston compression in the engine.

A synthesized spheroid particle (SSP) method is proposed on the basis of the first principles of fluid dynamics for calculating consistently the atomization behaviors of spray droplets and liquid sheets injected, the mixing of air and fuel, and the wall-impingement of droplet. The method includes a formulation for evaluating the collision of droplets accurately. The atomization process of the conical sheet of liquid fuel injected from a simplex nozzle is simulated by the SSP method for a wide range of back pressures and initial cone angles.

The piston rings, the engine sliding parts, are required to further contribute on mechanical loss reduction in order to improve fuel efficiency. However, many cases of the abnormal combustion due to oil upward flow, as well as the increase in oil consumption have been reported. Therefore, elucidation of the mechanism of those phenomena is still an urgent task. It is widely known that the distribution of the sliding face pressure in between the piston ring and the cylinder bore largely influence the oil flow via the sliding face of the piston ring. However, there are many unknown aspects in this field. Therefore, verification of the sliding face pressure during the actual operation is necessary in order to elucidate the mechanism of oil consumption. The thin-film sensor, since it has little influence on shape, is widely used as a measurement method of the sliding face pressure between two different faces, however this method has never been applied to the piston ring in the past.

1 Piston design approach for automotive engines has been advanced from both experimental and calculation analysis. However, the developments of experimental analysis method that can verify the accuracy of the calculation analysis are required. In this paper, multi-point thin-film pressure sensor for piston pin-boss part (hereinafter pin-boss) was sputtered on piston pin sliding surface and oil-film pressure distribution was measured in axial and circumferential direction using the pin-boss fatigue tester. Two kinds of pistons with different pin-boss shape (tapered shape) were used in the experiment. The peak pressure of piston with large tapered shape was higher about 20%, compared to the piston with the small tapered shape. As a result of oil film pressure distribution in circumferential direction, it has measured that the oil-film pressure at near side relief was higher than that of piston top side.

We proposed a new compressive combustion principle for an inexpensive and relatively quiet engine reactor that has the potential to achieve incredible thermal efficiency. The high efficiency can be achieved with colliding supermulti-jets that create complete air insulation to encase burned gas around the chamber center. We developed a small prototype engine system for gasoline, which has a strongly-asymmetric double piston and the supermulti-jets colliding with pulse. In this report, we will show combustion experimental results at startup and at steady state operation. We obtained exhaust temperature over 100 degree Celsius and pressure data, which imply auto-ignition occurrence of gasoline.

A new engine concept based on pulsed supermulti-jets colliding at a small area around the chamber center was proposed in our previous research. It was expected to provide noiseless high compression ratio and nearly-complete air-insulation on chamber walls, leading to high thermal efficiency. In the previous reports, three-dimensional computations for the unsteady compressible Navier-Stokes equation were conducted, which were qualitative because of using regular grid method. This time, we develop a new numerical code in order to quantitatively simulate the compression level caused by the jets colliding with pulse. It is achieved by applying a staggered grid method to improve conservatibity of physical quantities at very high compression in combustion phenomena. Computations at a simple condition were fairly agreed with a theoretical value. Computational results obtained for a complex geometry of an engine by the new code had less error than one with previous codes.

This paper proposes a new compressive combustion principle for an inexpensive, lightweight, and relatively quiet engine reactor that has the potential to achieve incredible thermal efficiency over 60% even for small engines having strokes shorter than 100mm, whereas eco-friendly gasoline engines for today's automobiles use less than 35% of the supplied energy for work on average. This level of efficiency can be achieved with colliding supermulti-jets that create air insulation to encase burned gas around the chamber center, thereby avoiding contact with the chamber walls, including the piston. Emphasis is also placed on the fact that higher compression results in less combustion noise because of the encasing effect. We will first show that numerical computations done for two jets colliding in line quantitatively agree with shock-tube experiment and theoretical value based on compressible fluid mechanics.