Search Results

The NASA Lewis Research Center in Cleveland, Ohio has completed the development and integration of a Power Management and Distribution (PMAD) DC Testbed. This testbed is a reduced scale representation of the end to end, sources to loads, Space Station Freedom Electrical Power System (SSF EPS). This unique facility is being used to demonstrate DC power generation and distribution, power management and control, and system operation techniques considered to be prime candidates for the Space Station Freedom. A key capability of the testbed is its ability to be configured to address system level issues in support of critical SSF program design milestones. Electrical power system control and operation issues like source control, source regulation, system fault protection, end-to-end system stability, health monitoring, resource allocation and resource management are being evaluated in the testbed.

The performance of two 20-kHz actuator power systems being built for an advanced launch system are evaluated for a typical launch scenario using an end-to-end system simulation. Aspects of system performance ranging from the switching of the power electronic devices to the vehicle aerodynamics are represented in the simulation. It is shown that both systems adequately stabilize the vehicle against a wind gust during a launch. However, it is also shown that in both cases there are bus voltage and current fluctuations which make system power quality a concern.

Since the beginning of the Space Station Freedom Program (SSFP), the Lewis Research Center (LeRC) has been actively involved in the development of electrical power system test beds to support of the overall design effort. Throughout this time, the SSFP Program has changed the design baseline numerous times, however, the test bed effort has endeavored to track these changes. Beginning in August 1989 with the baselining of an all DC System, a test bed was developed which supported this design baseline. However, about the time of the Test Bed's Completion in December 1990, the SSFP was again going through another design scrub known as Restructure. This paper describes the LeRC PMAD DC Test Bed and highlights the changes that have taken place in the Test Bed configuration and design resulting from the SSFP Restructure Exercise in December 1990.

The National Aeronautics and Space Administration (NASA), Lewis Research Center (LeRC) is responsible for the development, fabrication, and assembly of the electric power system (EPS) for the Space Station Freedom (SSF). The Power Management and Distribution (PMAD) Systems Testbed was assembled to support the design and early evaluation of SSF EPS operating concepts. The PMAD Systems Testbed represents a portion of the SSF EPS, containing intelligent switchgear, power conditioning devices, and the EPS Controllers. The PMAD Systems Testbed facility is discussed, including the power sources and loads available. A description of the PMAD Data System (PDS) is presented. The PDS controls the testbed facility hardware, monitors and records the EPS control data bus and external data. The external data includes testbed voltages and currents along with facility temperatures, pressures, and flow rates. Transient data is collected utilizing digital oscilloscopes.

Free-piston Stirling power converters are a candidate for high capacity space power applications. The Space Power Research Engine (SPRE), a free-piston Stirling engine coupled with a linear alternator is being tested at the NASA Lewis Research Center in support of the Civil Space Technology Initiative. The SPRE is used as a test bed for evaluating converter modifications which have the potential to improve converter performance and for validating computer code predictions. Reducing the number of cooler tubes on the SPRE has been identified as a modification with the potential to significantly improve power and efficiency. This paper describes experimental tests designed to investigate the effects of reducing the number of cooler tubes on converter power, efficiency and dynamics. Presented are test results from the converter operating with a reduced number of cooler tubes and comparisons between this data and both baseline test data and computer code predictions.

Jet Engines may experience severe vibration due to the sudden imbalance caused by blade failure. This research investigates employment of on board magnetic bearings or piezolectric actuators to cancel these forces in flight. This operation requires identification of the source of the vibrations via an expert system, determination of the required phase angles and amplitudes for the correction forces, and application of the desired control signals to the magnetic bearings or piezo electric actuators. This paper will show the architecture of the software system, details of the control algorithm used for the sudden imbalance correction project described above, and the laboratory test results.

Joining of a PdCr Strain Gage with a Hastelloy X carrier shim to Inconel by a rapid infrared processing technique has been investigated at 1150 °C using a nickel based brazing alloy AMS 4777, Ni-7Cr-3Fe-3.2B-4.5Si-.06C in wt%. The effects of the infrared joining parameters on the joint and base material microstructure, joint shear strength, and delamination tendency of the PdCr gage was investigated. Results show that the joint shear strength is as high as 503 MPa when processed at approximately 1150 °C for 120 seconds. Microstructural examinations of the joint with both an optical microscope and a scanning electron microscope indicate that good wetting exists between the brazing alloy with both the Hastelloy X and Inconel 718. And, the Hastelloy X and Inconel 718 exhibits no noticeable change in microstructure due to the rapid processing cycle of the infrared heating process while the stabilized PdCr wire gage shows little change in resistance.