Search Results

Optical fiber has begun replacing copper in avionic networks. So far, however, it has been mainly restricted to non-critical applications (video transmission to the flight deck, IFE?). In order to take advantage of the high-bandwidth, low weight, no EMI properties of optical fibers in all data transmission networks, it will be necessary to improve the testing. One part of the puzzle, which is still missing, is the self-test button: the possibility to check the network and detect potential failures before they occur. The typical testing tool of a technician involved in optical fiber cables is the ?light source ? optical power meter? pair. With this tool, one can measure the insertion loss of the fiber link. A second important parameter, the return loss at each optical connector, is not analysed. In addition, this is only a global measurement, which does not allow the detection of possible weak points.

The copper-rotor induction-motor made its debut in automotive electric traction in 1990 in GM's Impact EV. Since then, this motor architecture has covered millions of miles on other vehicle platforms which will soon include Toyota's RAV4-EV. With the industry's attention focused on cost-effective alternatives to permanent-magnet traction motors, the induction motor has returned to the spotlight. This talk will overview where the copper-rotor induction-motor is today, how the technology has evolved since the days of the GM Impact, the state-of-play in its mass-manufacturing processes and today's major supply-chain players. Presenter Malcolm Burwell, International Copper Association Inc.

Abstract Current End-of-Life Vehicle (ELV) recycling processes are mainly based on mechanical separation techniques. These methods are designed to recycle those metals with the highest contribution in the vehicle weight such as steel, aluminum, and copper. However, a conventional vehicle uses around 50 different types of metals, some of them considered critical by the European Commission. The lack of specific recycling processes makes that these metals become downcycled in steel or aluminum or, in the worst case, end in landfills. With the aim to define several ecodesign recommendations from a raw material point of view, it is proposed to apply a thermodynamic methodology based on exergy analysis. This methodology uses an indicator called thermodynamic rarity to assess metal sustainability. It takes into account the quality of mineral commodities used in a vehicle as a function of their relative abundance in Nature and the energy intensity required to extract and process them.

A laboratory study was performed to optimize a zoned configuration of an iron (Fe) SCR catalyst and a copper (Cu) SCR catalyst in order to provide high NOx conversion at lean A/F ratios over a broad range of temperature for diesel and lean-burn gasoline applications. With an optimized space velocity of 8,300 hr-1, a 67% (by volume) Fe section followed by a 33% Cu section provided at least 80% NOx conversion from approximately 230°C to 640°C when evaluated with 500 ppm NO and NH3. To improve the lean lightoff performance of the SCR catalyst system during a cold start, a Cu SCR catalyst that was 1/4 as long as the rear Cu SCR catalyst was placed in front of the Fe SCR catalyst. When evaluated with an excess of NH3 (NH3/NO ratio of 2.2), the Cu+Fe+Cu SCR system had significantly improved lightoff performance relative to the Fe+Cu SCR system, although the front Cu SCR catalyst did decrease the NOx conversion at temperatures above 475°C by oxidizing some of the NH3 to N2 or NO.

A laboratory study was performed to assess the effects of SO2 poisoning on the NOx conversion of iron (Fe) and copper (Cu) SCR catalysts. Thermally aged samples of the catalysts were poisoned with SO2 under lean conditions. At various times during the poisonings, the samples were evaluated for NOx conversion with NO and NH3 using lean temperature ramps. The low temperature NOx conversions of both catalysts decreased by 10 to 20% after 1 to 4 hours of poisoning but were stable with continued exposure to the SO2. The poisoned Cu SCR catalyst could be desulfated repeatedly with 5 minutes of lean operation at 600°C. Initially, the poisoned Fe SCR catalyst required 5 minutes of lean operation at 750°C to recover its maximum NOx conversion.

This paper aims to indicate the advantages and any drawbacks of high frequency alternating current (HFAC) power for vehicle auxiliary electrical systems. Generally, benefits of HFAC include efficient power distribution and transformation, space and weight saving and load galvanic isolation. In addition, HFAC bus topologies are distributed to the point of use, lending the system to easy fault detection. The paper is structured as follows: first, the main findings of the most relevant automotive HFAC studies are outlined. Next, an HFAC architecture is proposed which is compared to the existing 14V and proposed 42V centralised DC networks in terms of power distribution efficiency and wiring harness weight saving. For this analysis, the case study of a medium-sized passenger vehicle is considered, and a group of intermittent and continuous auxiliary loads with a cumulative power of 2.8kW.

In the sensitive automotive applications like the safety restraint systems (SRS), twisted lines can be used to link the components of the system because of their property of reduction of the electromagnetic interference (EMI) coupling. Compared to the parallel lines, the twisted lines present the drawback to consume more copper in their manufacturing due to the greater length of their conductors. A parametric study based on the numerical modeling and the measurement of twisted lines is conducted in order to analyze the effect of the twisting pitch and of the untwisted part of these lines on the level of EMI coupling. This study will enable to optimize these two parameters in order to reduce the level of EMI coupling as well as the length of the conductors of the lines.

Non-road Tier 4 Final emissions standards offer opportunities for engines to be certified with DOC + SCR aftertreatment systems (ATS), where particulate matter (PM) emissions will be controlled by engine measures. These non-filter systems will not experience high thermal conditions common for filter regeneration and, therefore, will not have the secondary benefit of thermal events removing sulfur from the DOC and SCR aftertreatment. An experimental program was conducted on DOC + SCR systems in which the DOC was selected for the anticipated NO2 and sulfur management requirements of a fixed volume of 3 SCR types (vanadia, copper and iron). Each system was optimized to NOx conversion levels of 90%+ on NRTC cycles then exposed to accelerated sulfur poisoning and various cycles of increasing temperature after each poisoning to observe the performance recovery of the system. Specific sulfur management strategies are defined, depending on technology.

Failure mode and fatigue behavior of dissimilar laser welds in lap-shear specimens of aluminum and copper sheets are investigated. Quasi-static tests and fatigue tests of laser-welded lap-shear specimens under different load ranges with the load ratio of 0.1 were conducted. Optical micrographs of the welds after the tests were examined to understand the failure modes of the specimens. For the specimens tested under quasi-static loading conditions, the micrograph indicates that the specimen failed through the fusion zone of the aluminum sheet. For the specimens tested under cyclic loading conditions, two types of failure modes were observed under different load ranges. One failure mode has a kinked crack initiating from the interfacial surface between the aluminum and copper sheets and growing into the aluminum fusion zone at an angle close to 90°.

Measuring deformation under dynamic loading is still a key problem in the automobile industry. The first spatial phase-shift shearography system for relative deformation measurement is reported. Traditional temporal phase-shift technique-based shearography systems are capable of measuring relative deformation by using a reference object. However, due to its low acquisition rate, the existing temporal phase-shift shearography system can be only used under static loading situations. This paper introduces a digital shearography system which utilizes the spatial phase-shift technique to obtain an extremely high acquisition rate. The newly developed spatial phase-shift shearography system uses a Michelson-Interferometer as the shearing device. A high power laser at 532nm wavelength is used as the light source. A one mega pixels high speed CCD camera is used to record the speckle pattern interference.

The demand for light weight vehicles continues to stimulate extensive research into the development of light weight casting alloys and optimization of their manufacturing processes. Of primary relevance are Aluminum (Al) and Magnesium (Mg) based alloys, which have successfully replaced selected iron based castings in automobiles. However, optimization of as-cast microstructure, processing and performance remains a challenge for some Al-based alloys. In this context, placement of chills in castings has been frequently used to locally manipulate the solidification conditions and microstructure of a casting. In this work, the effect of using an active copper chill on the residual strain profile of a sand-cast B319 aluminum alloy was investigated. Wedge-shaped castings were produced with three different cooling conditions: copper plate chill, copper pipe with cooling water and no chill (baseline).

Stricter emission limitations for NOx and particulates in mobile diesel applications will require the combinations of active aftertreatment methods like Diesel Particulate Filters (DPF), Selective Catalytic Reduction (SCR) with urea and Lean NOx Trap (LNT) in the 2010's. A new concept is the combination of LNT+SCR, which enables on-board synthesis of ammonia (LNT), which is then removed on the SCR catalyst. The main application for this kind system will be light-duty vehicles, where LNTs are already used and the low temperature deNOx is a main target. That combinatory system was investigated by developing and selecting PtRh/LNT and SCR catalysts for that particulate application, where the maximum temperature may reach 800°C and SCR should proceed without NO2 assistance. Pt-rich, PtRh/LNT with reasonable high loadings above 80g/cft resulted in a high NOx efficiency in the experimental laboratory conditions which created also on LNTs a higher NH3 concentration for the SCR unit.

Ultrasonic fatigue tests (testing frequency around 20 kHz) have been conducted on four different cast aluminum alloys each with a distinct composition, heat treatment, and microstructure. Tests were performed in dry air, laboratory air and submerged in water. For some alloys, the ultrasonic fatigue lives were dramatically affected by the environment humidity. The effects of different factors like material composition, yield strength, secondary dendrite arm spacing and porosity were investigated; it was concluded that the material strength may be the key factor influencing the environmental humidity effect in ultrasonic fatigue testing. Further investigation on the effect of chemical composition, especially copper content, is needed.

A pre-treatment technique for improving coating adhesion on stainless steel has been developed. This method dramatically enhances the adhesion between the stainless steel and the coating by pre-treating the stainless steel with a known nickel strike plating for a short period of time. Furthermore, when this process was applied to stainless fuel filler pipes to improve corrosion resistance, layout restrictions and chipping covers became unnecessary, costs were reduced, and vehicle weight was lowered.

Foundry industries are very much familiar and rich experience of producing ferrous castings mainly Flake Graphite (FG) and Spheroidal Graphite (SG) cast iron. Grey cast iron material is mainly used for dampening applications and spheroidal graphite cast iron is used in structural applications wherein high strength and moderate ductility is necessary to meet the functional requirements. However, both types of cast iron grades are very much suitable in terms of manufacturing in an economical way. Those grades are commercially available and being consumed in various industries like automotive, agriculture etc, High strength SG Iron grades also being manufactured by modifying the alloying elements with copper, chromium, manganese andcobalt. but it has its own limitation of reduction in elongation when moving from low to high strength SG iron material. To overcome this limitation a new cast iron developed by modifying the chemical composition.

The present study looks into different possibilities for tribological optimization of the piston/bore system in heavy duty diesel engines. Both component rig tests and numerical simulations are used to understand the roles of surface specifications, ring pack, and lubricant in the piston/bore tribology. Run-in dynamics, friction, wear and combustion chamber sealing are considered. The performance of cylinder liners produced using a conventional plateau honing technology and a novel mechanochemical surface finishing process - ANS Triboconditioning® - is compared and the importance of in-design “pairing” of low-viscosity motor oils with the ring pack and the cylinder bore characteristics in order to achieve maximum improvement in fuel economy without sacrificing the endurance highlighted. A special emphasis is made on studying morphological changes in the cylinder bore surface during the honing, run-in and Triboconditioning® processes.

The prime function of crown wheel pinion is to receive the power from transmission & distribute to two-wheel ends. Doing so these members will experience the tremendous bending fatigue. Shot peen is the one of the latest technology used to improve the bending fatigue of the CWP [1]. In this particular case- six CWP are taken for the study to understand the effect of the operations after shot peen process. Three Samples are named as batch A, another 3 samples are named as batch B. Both the batch CWP are shot peened. Then as a regular production practice the batch A CWP are process through hard turning ➔ Abrasive lapping ➔ Hot lubriting (manganese phosphate) ➔ Fully finish ready for assembly. Then both the batch A & batch B samples are taken for residual stress analysis using X-Ray diffraction technique. The measurement location is 50 microns below the surface. The results tabulated, found that batch A samples shows decrease in Residual stress relatively to batch B.

The advent of more efficient direct injection turbocharged engines has increased the need for higher performance connecting rods, able to withstand in particular higher compressive loads in operation. In this respect, new high strength materials for powder forged connecting rods were developed and introduced in production with excellent results. Among them, HS170M is currently used to manufacture connecting rods for several high performance engines, which not only have higher strength, but have less variation in their mechanical properties. The results of numerous benchmark studies have shown that powder forged connecting rods manufactured with HS170M are stronger than their steel forged counterparts manufactured with microalloyed steels, are easier to machine and fracture split, and represent a cost effective way to manufacture this important high reliability automotive component.

In this paper, the analytical stress intensity factor and J integral solutions for welds in lap-shear specimens of two dissimilar sheets based on the beam bending theory are first reviewed. The solutions are then presented in the normalized forms. Next, two-dimensional finite element analyses were selectively conducted to validate the analytical solutions based on the beam bending theory. The interface crack parameters, the stress intensity factor solutions, and the J integral solutions for welds in lap-shear specimens of different combinations of steel, aluminum, and magnesium, and the combination of aluminum and copper sheets of different thickness ratios are then presented for convenient fracture and fatigue analyses. The transition thickness ratios for critical crack locations for different combinations of dissimilar materials are then determined from the analytical solutions.

This work reports on measurement and analysis of the galvanic interaction between steel self-piercing rivets (SPRs) having several different surface conditions and magnesium alloy substrates under consideration for use in automotive structural assemblies. Rivet surface conditions included uncoated steel, conventional Zn-Sn barrel plating and variations of commercial aluminizing processes, including supplemental layers and sealants. Coating characteristics were assessed using open circuit potential (OCP) measurement, potentiodynamic polarization scanning (PDS), and electrochemical impedance spectroscopy (EIS). The degree of galvanic coupling was determined using zero-resistance ammeter (ZRA) and the scanning vibrating electrode technique (SVET), which also permitted characterization of galvanic current flows in situ.