Search Results

Global warming due to exhaust emissions, rapid depletion of crude oil, and strict carbon control legislation has forced researchers to search biofuels as substitute for petroleum diesel fuels. Biodiesel is a renewable and oxygenated fuel. It is free from sulfur, non-toxic and a biodegradable. The different non-edible vegetable oils such as Algae, Karanja and Jatropha could be used to produce biodiesel. Biodiesel is a green fuel with an exception that it emits 15-20% more NOx as compared to diesel fuel. The emissions of nanoparticles are more hazardous to human health. The nanoparticles emission of biodiesel must be measured according to the new strict regulations. The engine performance and the lower emission characteristics, except for NOx emission, for Algae, Karanja and Jatropha oil biodiesels are similar to those of diesel fuel.

The winter of 2013-2014 provided an opportunity to operate off-road vehicles in cold weather for extended time as part of a vehicle/tier 4 diesel engine validation program. An unexpected area of study was the performance of high efficiency, on engine, fuel filters during continuous vehicle operation in cold weather. During the program we observed unexpected premature fuel filter plugging as indicated by an increase in pressure drop across the filter while in service. Field and laboratory testing was completed at John Deere and Donaldson to understand the cause of filter plugging. Although conditions were found where winter fuel additives could cause plugging of high efficiency filters, premature filter plugging occurred even when testing with #1 diesel fuel. This fuel contained no additives and was used at temperatures well above its cloud point.

Considerable development effort has shown that conventional diesel engine lubricating oil specifications do not define the needs for acceptable injector life in methanol-fueled, two-stroke cycle diesel engines. A cooperative program was undertaken to formulate an engine oil-fuel additive system which was aimed at improving performance with methanol fueling. The performance feature of greatest concern was injector tip plugging. A Taguchi matrix using a 100 hour engine test was designed around an engine oil formulation which had performed well in a 500 hour engine test using a simulated urban bus cycle. Parameters investigated included: detergent level and type, dispersant choice, and zinc dithiophosphate level. In addition, the influence of a supplemental fuel additive was assessed. Analysis of the Taguchi Matrix data shows the fuel additive to have the most dramatic beneficial influence on maintaining injector performance.

Abstract Previous studies have shown that injector aging adversely affects the diesel engine spray formation and combustion. It has also been shown that the oxygenated fuel additive tripropylene glycol monomethyl ether (TPGME) can lower soot emissions. In this study, the effects of injector aging and TPGME on the late-cycle oxidation of soot were investigated using laser diagnostic techniques in a light-duty optical diesel engine at two load conditions. The engine was equipped with a quartz piston with the same complex piston geometry as a production engine. Planar laser-induced incandescence (LII) was used to obtain semiquantitative in-cylinder two-dimensional (2D) soot volume fraction (fv ) distributions using extinction measurements. The soot oxidation rate was estimated from the decay rate of the in-cylinder soot concentration for differently aged injectors and for cases with and without TPGME in the fuel.

Automotive and railroad diesel fuels, in general, are derived from petroleum refinery products which are commonly referred to as middle distillates. Middle distillates represent products which have a higher boiling range than gasoline and are obtained from fractional distillation of the crude oil or from streams from other refining processes. Finished diesel fuels represent blends of middle distillates. The properties of commercial distillate diesel fuels depend on the refinery practices employed and the nature of the crude oils from which they are derived. Thus, they may differ both with and within the region in which they are manufactured. Such fuels generally boil over a range between 163 and 371 °C (325 to 700 °F). Their makeup can represent various combinations of volatility, ignition quality, viscosity, sulfur level, gravity, and other characteristics. Additives may be used to impart special properties to the finished diesel fuel.

Automotive and locomotive diesel fuels, in general, are derived from petroleum refinery products which are commonly referred to as middle distillates. Middle distillates represent products which have a higher boiling range than gasoline and are obtained from fractional distillation of the crude oil or from streams from other refining processes. Finished diesel fuels represent blends of middle distillates and may contain other blending components of substantially non-petroleum origin, such as biodiesel fuel blend stock, and/or middle distillates from non-traditional refining processes, such as gas-to-liquid processes. The properties of commercial distillate diesel fuels depend on the refinery practices employed and the nature of the crude oils from which they are derived. Thus, they may differ both with and within the region in which they are manufactured. Such fuels generally boil, at atmospheric pressure, over a range between 130 °C and 400 °C (approximately 270 °F to 750 °F).

This SAE Standard describes those factors which affect the accuracy and reliability of voltage indicating units and electrical indicating and sending units for fuel level, pressure, and temperature suitable for off-road, self-propelled work machines as described in SAE J1116. Indicating units are divided into two groups, fully sealed and partially sealed. Serviceable lighting is not covered by this document unless otherwise specified. No ISO document has been found to be compatible.

Fuel is the single largest operating expense for a diesel truck fleet. This paper presents data on the many factors which affect consumption, and on the ways in which fuels and additives can contribute to minimizing it. Fuel density is the key fuel parameter affecting consumption, since higher density fuels deliver more energy per litre than those of lower density. Diesel cold flow improver additives can play an important role in the economic production of diesel fuel. In addition, they allow the production of higher density fuels while maintaining good low temperature performance. Dynamometer test data are presented to show the effects of ambient temperature, vehicle speed and fuel density on consumption. The performance of flow improver additives in improving low temperature operability while maximizing density is demonstrated.

The use of biodiesel as alternative to fossil fuel for light duty CI engines to reduce greenhouse gas emissions was widely investigated. However, poor stability of biodiesel - diesel mixture limits the use of biodiesel to low volume concentrations. This paper presents the results concerning the use of a novel fuel additive package containing antioxidant (AS), pour-point depressant (D) and biocide (Bi) with the aim to increase the quality and amount of biodiesel in the diesel-biodiesel blends. Some of the goals are linked to the degradative effects due to free radicals oxidation, contamination by water and microorganisms. The interaction between two different additive packages and two biodiesel (soybean and rapeseed) - diesel blends at 20% in volume was investigated. Optical studies have been performed to characterize the spatial and temporal spray evolution both in a high pressure quiescent vessel and in an optically-accessible single-cylinder 2-stroke CI engine.

The use of a copper diesel fuel additive in an emission control system improves particulate oxidation. This expands the operability of available systems by reducing the particulate mass loading and related external energy consumption required during regeneration. Easier, more frequent regenerations improve overall engine/system efficiency and reduce thermal stress on filtration media. Procedures for optimizing additive use are presented. In addition, the results from a health study are reviewed.

Emission tests were conducted on a Mack MH613 heavy duty truck equipped with a 1986 specification Mack EC-6-350 engine. The engine was equipped with the Garrett exhaust aftertreatment system. The tests were conducted by CARB (California Air Resources Board) and Garrett at the CARB El Monte, Calif. facility on a chassis dynamometer. Emission tests were also conducted on a 1989 specification 14 liter 310 HP six cylinder engine in a test cell using the EPA transient cycle. Those tests were conducted at a different facility. Tests were conducted without a particulate trap, with an uncatalyzed trap, with a catalyzed trap and with an uncatalyzed trap and fuel additive. Low sulfur (0.05%) fuel was used, except for a single test run on 0.20% fuel. With the CARB 8 point test cycle, results cannot be directly compared to those obtained using the EPA transient cycle. However, the results appear to be representative and trends should be accurate.

Exhaust gas composition and particulate matter emission levels were obtained from in-use heavy duty transit buses powered by 6V-92TA engines with different fuels. Vehicles discussed in this study were pulled out of revenue service for a day, in Phoenix, AZ, Pittsburgh, PA and New York, NY and tested on the Transportable Heavy Duty Vehicle Emissions Testing Laboratory employing a transient chassis dynamometer. All the vehicles, with engine model years ranging from 1982 to 1992, were operated on the Federal Transit Administration Central Business District Cycle. Significant reductions in particulate matter emissions were observed in the 1990-1992 model year vehicles equipped with the trap oxidizer systems. Testing vehicles under conditions that represent “real world” situations confirmed the fact brought to light that emission levels are highly dependent upon the maintenance and operating conditions of the engines.

This research quantifies the effects of a copper fuel additive on the regulated [oxides of nitrogen (NOx), hydrocarbons (HC) and total particulate matter (TPM)] and unregulated emissions [soluble organic fraction (SOF), vapor phase organics (XOC), polynuclear aromatic hydrocarbons (PAH), nitro-PAH, particle size distributions and mutagenic activity] from a 1988 Cummins LTA10 diesel engine using a low sulfur fuel. The engine was operated at two steady state modes (EPA modes 9 and 11, which are 75 and 25% load at rated speed, respectively) and five additive levels (0, 15, 30, 60 and 100 ppm Cu by mass) with and without a ceramic trap. Measurements of PAH and mutagenic activity were limited to the 0, 30 and 60 ppm Cu levels. Data were also collected to assess the effect of the additive on regeneration temperature and duration. Copper species collected within the trap were identified and exhaust copper concentrations quantified.

Most particulate traps efficiently retain soot of diesel engine exhaust but the potential hazard to form secondary emissions has to be controlled. The Diesel Particle Filter (DPF) regeneration is mainly supported by metal additives or metallic coatings. Certain noble or transition metals can support the formation of toxic secondary emissions such as Dioxins, Polycyclic Aromatic Hydrocarbons (PAH), Nitro-PAH or other volatile components. Furthermore, particulate trap associated with additive metals can penetrate through the filter system or coating metals can be released from coated systems. The VERT test procedure was especially developed to assess the potential risks of a formation of secondary pollutants in the trap. The present study gives an overview to the VERT test procedure. Aspects of suitability of different fuel additives and coating metals will be discussed and examples of trap and additive induced formation of toxic secondary emissions will be presented.

This study examines the effect of a ceramic particle trap and a manganese fuel additive on the mutagenic activity and chemical composition of diesel exhaust particulate matter from a heavy-duty mining engine. Particles were collected by dilution tunnel sampling from a 4-cylinder, Caterpillar 3304, naturally-aspirated, indirect-injection engine operated at six steady-state conditions. Depending on engine load and speed the ceramic particle trap reduced the following emissions: particulate matter, 80 – 94%; soluble organic fraction (SOF), 83 – 95%; 1-nitropyrene, 94 – 96%; and SOF mutagencity, 72% (cycle-weighted average). When the Mn fuel additive was used without a ceramic particle trap the total cycle mutagenic activity emitted increased 7-fold, in part, due to elevated emissions of 1-nitropyrene.

Abstract Due to the nature of diffusive combustion, diesel engines display a distinct trade-off between nitrogen oxide (NOX) and particulate matter (PM). Since emission regulations become ever stricter, the relevance of dissolving this trade-off increases steadily as it hinders engine development from achieving ultralow emission levels. Seeking new opportunities to approach the problem, the modification of fuel properties has gained much attention. In particular, oxygenated fuels reduce particle emissions drastically, while having little adverse impact on NOX. Similarly, water (H2O) emulsification of diesel is commonly reported to reduce both NOX and PM. Both methods appear very promising, yet only few investigations were conducted in an effort of combing the benefits of the two. With this work, the authors provide a detailed study on combustion and emissions for both neat oxymethylene ethers (OME2-OME5) and an H2O-emulsified OME mixture (OMEmix).

Global warming with stringent emission legislation along with the depletion of fossil fuel has given us an opportunity to find biodiesel as alternative to diesel fuel. Biodiesel has been widely accepted as comparable fuel to diesel in diesel engine. This is due to its renewable property, better lubricity, along with lesser gaseous emission as compared to diesel fuel. However, there is a major disadvantage in the use of biodiesel as it increases NOx emission. Fuel additive becomes one of the essential tools to overcome the drawback of biodiesel required to meet the international standard of performance and emission. In this study, the performance, combustion, and gaseous emission of CO, CO2, HC, NOx and PM including particle size number distribution characteristics, were compared for diesel, Karanja oil biodiesel, and Karanja oil biodiesel with Cerium Oxide Nano particles fuel additive, in a 12 cylinder, 585 kW, CIDI military diesel engine.

Biodiesel fuels are an alternative to diesel fuel. Biodiesel is an oxygenated, sulphur free, non-toxic, biogradable and renewable fuel. It is derived from vegetable oils. Since straight vegetable oils have quite high viscosity compared to mineral diesel, they have to be modified to bring their combustion-related properties and viscosity closer to mineral diesel. This is done by modifying their molecular structure through a transesterification process. In the present study, a military heavy duty 38.8 liter, 585 kW supercharged, compression ignition diesel injection (CIDI) engine was fuelled with diesel, Karanja oil methyl ester (KOME) biodiesel, and KOME biodiesel with cerium oxide fuel additive, respectively. These were subjected to 100 hours long term endurance tests. Lubricating oil samples, drawn from the engine fuelled with these fuels after a fixed interval of 20 hours, were subjected to elemental analysis.

Oxygenated fuel additives are currently an important research topic for particulate emissions reduction in diesel engines with direct injection (DI) to meet future emission regulations. In this work more than twenty oxygenated hydrocarbons from the literature were considered as diesel fuel additives. Butylal (an acetal compound, chemical formula C9H20O2) offers significant advantages over most other oxygenates in that its physical properties are very close to those of common diesel fuel. Wear scar measurements were conducted to evaluate the lubricity characteristics of diglyme (C6H14O3), ethyldiglyme (C8H18O3), butylal and different diesel-butylal mixtures. The results reveal the low lubricity of all oxygenated compounds. Thus, for the engine tests, a lubricity improver has been added to the diesel-butylal mixtures.