Search Results

Standard

STANDARD FOR D.C. BRUSH MOTOR - HVAC BLOWERS

2020-11-19

CURRENT

USCAR6-1

This standard sets forth the performance and durability requirements for 12-volt, D.C. brush-type electric motors used for automobile Heating, Ventilation, and Air Conditioning (HVAC) blowers and outlines Production Validation and Continuing Conformance testing.

Standard

STANDARD FOR D.C. BRUSH MOTOR – HVAC BLOWERS

1999-02-01

HISTORICAL

USCAR6

This standard sets forth the performance and durability requirements for 12-volt, D.C. brush-type electric motors used for automobile Heating, Ventilation, and Air Conditioning (HVAC) blowers and outlines Production Validation and Continuing Conformance testing.

Standard

ERGONOMICS SPECIFICATION FOR MANUALLY SEATED FASTENERS

2020-12-30

CURRENT

USCAR47

This document describes the assembly force guidelines for manually seated push-pins, clips, and similar retention devices. For the purpose of this document, the term “clip” is used to reference all retention devices addressed within this document. Applicable retention devices must have force exerted directly to the clip using the finger/thumb and are hand seated independent of other fasteners. For a retention device to be manually installed and seated independent of other retention devices, it must be seated fully without any interaction with an adjacent fastener (i.e., multiple PIA clips on the back of a hard trim panel). This standard applies to contact surfaces angled at 90 degrees (±10 degrees) and/or perpendicular from the direction of force insertion. Mechanically installed fasteners (screws, rivets, etc.) are not included in this document. This standard does not apply to extraction/retention forces.

Standard

FIELD CORRELATED LIFE TEST SUPPLEMENT TO SAE/USCAR-2

2001-12-01

HISTORICAL

USCAR20

This life test for underhood/passenger/trunk connector systems may be used in place of Section 5.8.6 (Connector System Electrical Test Flow Chart) of SAE/USCAR-2. All other requirements of SAE/USCAR-2 remain applicable even when this test is used. Refer to SAE/USCAR-2 and Connector/Terminal Supplier for appropriate power rating and current cycle Testing.

Standard

FIELD CORRELATED LIFE TEST SUPPLEMENT TO SAE/USCAR-2

2022-03-15

CURRENT

USCAR20-2

This life test for underhood/passenger/trunk connector systems may be used in place of Section 5.9.6, Connection System Electrical Table of SAE/USCAR-2. All other requirements of SAE/USCAR-2 remain applicable even when this test is used. Refer to SAE/USCAR-2 and Connector/Terminal Supplier for appropriate power rating and current cycle Testing.

Standard

FIELD CORRELATED LIFE TEST SUPPLEMENT TO SAE/USCAR-2

2004-06-23

HISTORICAL

USCAR20-1

This life test for underhood/passenger/trunk connector systems may be used in place of Section 5.9.6, Connection System Electrical Table of SAE/USCAR-2. All other requirements of SAE/USCAR-2 remain applicable even when this test is used. Refer to SAE/USCAR-2 and Connector/Terminal Supplier for appropriate power rating and current cycle Testing.

Standard

STANDARD FOR IN-TANK ELECTRIC FUEL PUMPS

1999-08-15

HISTORICAL

USCAR13

This standard covers the operational characteristics, environment, durability procedures, and test procedures for in-tank electric fuel pumps for automotive gasoline applications. Specific performance and test criteria used in conjunction with this procedure are specified on the pump drawing. Particular sections of this document may be required for all applications. This standard is intended to evaluate specific characteristics as a supplement to normal material inspections, dimensional checking, and in-process controls, and should in no way adversely influence other inspection operations.

Standard

TEST PROCEDURE FOR ELECTRICAL GROUND ATTACHMENTS

2022-02-25

HISTORICAL

USCAR26

This test procedure is intended to evaluate and/or validate electrical ground schemes for use on the body or chassis. There are two classes based on the expected environmental conditions. Exposed Grounds can be located anywhere in the vehicle (except on the powertrain) and is the class for which most schemes should be tested. Unexposed Grounds can only be used in the passenger compartment or trunk and as such are special cases. This procedure as written is not intended for testing powertrain grounds where high temperatures and vibration levels may be encountered. These situations may require modifications to this procedure and are left to the Responsible Engineer to determine. This specification does not specifically address validation of terminal to wire electrical crimps. Crimps are tested to SAE/USCAR-21

Standard

Dimensional and Performance Specification for After-Market Gasoline Engine Oil Filters

2013-01-30

HISTORICAL

USCAR36

This specification defines the dimensional and performance requirements for aftermarket spin-on oil filters intended for use on gasoline engines. Filters meeting this specification may also be suitable for use on some diesel applications. Filters meeting these dimensional limits are intended to meet the oil filter fit and package requirements for engine and vehicle designs. Filters meeting the performance requirements are intended to maintain sufficient durability to support many of the OEM's recommended oil change intervals. Some OEM engines may require special filters for which this specification would not support.

Standard

DIMENSIONAL AND PERFORMANCE SPECIFICATION FOR AFTER-MARKET GASOLINE ENGINE OIL FILTERS

2021-05-13

CURRENT

USCAR36-1

This specification defines the dimensional and performance requirements for aftermarket spin-on oil filters intended for use on gasoline engines. Filters meeting this specification may also be suitable for use on some diesel applications. Filters meeting these dimensional limits are intended to meet the oil filter fit and package requirements for engine and vehicle designs. Filters meeting the performance requirements are intended to maintain sufficient durability to support typical 10000 mile oil change intervals. Some OEM engines may require special filters for which this specification would not support. Filters that meet or exceed this specification requirements for both dimensional and performance can claim “Conformance to SAE/USCAR - 36 Specifications.” Filters that meet just the performance specifications (ie. may have different thread) can claim “Aligns to SAE/USCAR - 36 Performance Specifications.”

Standard

Shipping Caps, Torque Caps, and Body Plugs Ergonomic Design Criteria

2015-03-30

CURRENT

USCAR43

This document describes the design and assembly force guidelines for conventional shipping caps, torque caps, and body plugs. All possible design and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the-shelf” design, always consult the responsible Ergonomics Department.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2017-05-10

HISTORICAL

USCAR44

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises a) from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray and different thicknesses of the holes that the clip is inserted into.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2021-01-20

HISTORICAL

USCAR44-1

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray, and different thicknesses of the holes that the clip is inserted into.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2023-03-23

CURRENT

USCAR44-2

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray, and different thicknesses of the holes that the clip is inserted into.

Standard

PERFORMANCE SPECIFICATION FOR WELDED WIRE-TO-WIRE SPLICES

2018-06-14

CURRENT

USCAR45

SAE/USCAR-45 defines test methods and performance requirements for ultrasonically-welded wire-to-wire splices for automotive applications. Face-to-face, butt splice, and center strip configurations per Figure 1 can be tested. The tests defined in this specification subject samples on test to stresses that simulate a lifetime of exposure for a road vehicle. Stresses called out in this specification include thermal shock, temperature/humidity cycling and mechanical stress from different directions.

Standard

PERFORMANCE SPECIFICATION FOR MINIATURE AUTOMOTIVE COAXIAL CONNECTORS

2022-05-10

CURRENT

USCAR49

This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6mm and smaller. These are often called “Mini Coax connector systems.” This specification applies to coaxial cable connection systems that operate at frequencies from DC to 9 GHz and are intended for road vehicles. The characteristic impedance of the Mini-Coax connection system described here is 50 ohms, however nothing excludes the use of these connectors in systems with a different characteristic impedance. This specification applies only to connection systems using coaxial cable.

Standard

HIGH VOLTAGE CONNECTOR PERFORMANCE SUPPLEMENT TO SAE/USCAR-2

2008-08-27

CURRENT

USCAR37

Procedures included within this specification supplement are, when used in conjunction with SAE/USCAR 2, intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in high voltage (60~600V) road vehicle applications. These procedures are applicable to terminals used for In-Line, Header, and Device Connector systems with and without Shorting Bars. This supplement applies to both sealed and unsealed connection systems.

Standard

COAXIAL CABLE CONNECTOR INTERFACE – SQUARE OUTER CONDUCTOR

2002-02-22

HISTORICAL

USCAR19

This radio frequency (RF) connector interface specification is suited for unsealed automobile applications up to 2 GHz. Dimensional requirements are specified in this document to ensure interchangeability. This RF connector interface specification is intended for in-line, board mount, device mount, straight or angled applications. Performance requirements are specified in SAE/USCAR-2, and in SAE/USCAR-17.

Standard

COAXIAL CABLE CONNECTOR INTERFACE - SQUARE OUTER CONDUCTOR

2021-08-05

CURRENT

USCAR19-2

This radio frequency (RF) connector interface specification is suited for unsealed automobile applications up to 2 GHz. Dimensional requirements are specified in this document to ensure interchangeability. This RF connector interface specification is intended for in-line, board mount, device mount, straight or angled applications. Performance requirements are specified in SAE/USCAR-2, and in SAE/USCAR-17.

Standard

LEAD-FREE SOLDER VALIDATION TEST PLAN

2020-11-19

CURRENT

USCAR40-2

This guideline is applicable to existing lead solder production products that will change to lead-free solder processes to meet the ELV Directive 2000/53/EC Annex II, exemption 8B requirements. This guideline is applicable to similar products used by multiple OEM's that have the same manufacturing processes / equipment. The intent is to streamline the supplier’s environmental testing via common qualification to reduce timing, quantities, and costs.