Search Results

Standard

TEST PROCEDURES FOR EVALUATING BOLT-LOAD RETENTION OF MAGNESIUM ALLOYS

2020-11-19

CURRENT

USCAR35-1

A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications.

Standard

STANDARD FOR D.C. BRUSH MOTOR - HVAC BLOWERS

2020-11-19

CURRENT

USCAR6-1

This standard sets forth the performance and durability requirements for 12-volt, D.C. brush-type electric motors used for automobile Heating, Ventilation, and Air Conditioning (HVAC) blowers and outlines Production Validation and Continuing Conformance testing.

Standard

STANDARD FOR D.C. BRUSH MOTOR – HVAC BLOWERS

1999-02-01

HISTORICAL

USCAR6

This standard sets forth the performance and durability requirements for 12-volt, D.C. brush-type electric motors used for automobile Heating, Ventilation, and Air Conditioning (HVAC) blowers and outlines Production Validation and Continuing Conformance testing.

Standard

ERGONOMICS SPECIFICATION FOR MANUALLY SEATED FASTENERS

2020-12-30

CURRENT

USCAR47

This document describes the assembly force guidelines for manually seated push-pins, clips, and similar retention devices. For the purpose of this document, the term “clip” is used to reference all retention devices addressed within this document. Applicable retention devices must have force exerted directly to the clip using the finger/thumb and are hand seated independent of other fasteners. For a retention device to be manually installed and seated independent of other retention devices, it must be seated fully without any interaction with an adjacent fastener (i.e., multiple PIA clips on the back of a hard trim panel). This standard applies to contact surfaces angled at 90 degrees (±10 degrees) and/or perpendicular from the direction of force insertion. Mechanically installed fasteners (screws, rivets, etc.) are not included in this document. This standard does not apply to extraction/retention forces.

Standard

NEW FINISH DEVELOPMENT DOCUMENT

2020-11-19

CURRENT

USCAR32-1

This standard lists variables that shall be investigated and reported as an initial investigation into new or revised surface finishes intended for use on fasteners. This standard provides instruction for producing a final report that will be used to determine if further investigation of a surface finish is justified. Further investigation may include tests and evaluations specific to an individual OEM prior to introduction/approval of the surface finish. The final report shall include the results, observations, and conclusions for all of the variables. The final report may be made up of several individual reports covering each variable. In all cases the laboratory performing the test, the test date and the report approver shall be included in the final report.

Standard

STANDARD FOR TIRE TRACEABILITY CONTENT AND FORMAT FOR THE RADIO-FREQUENCY IDENTIFICATION (RFID) TAG AND ASSOCIATED TIRE DATA SET

2019-04-17

HISTORICAL

USCAR39

This standard describes a requirement for automotive tire traceability. It includes a definition of the RFID tag and the associated tire data set that can be accessed using the RFID tag as an identifier. The standard describes a unique identification and the associated data set for each tire produced by the tire fabricator. This data will either be provided or transmitted at the time of shipment to retailers, wholesalers or original equipment vehicle manufacturers. Tire identification code and data may be used for error proofing, determining the tire specifications or supporting any inquiries that occur for the duration of its automotive life.

Standard

STANDARD FOR TIRE TRACEABILITY CONTENT AND FORMAT FOR THE RADIO-FREQUENCY IDENTIFICATION (RFID) TAG AND ASSOCIATED TIRE DATA SET

2020-11-19

CURRENT

USCAR39-1

This standard describes a requirement for automotive tire traceability. It includes a definition of the RFID tag and the associated tire data set that can be accessed using the RFID tag as an identifier. The standard describes a unique identification and the associated data set for each tire produced by the tire fabricator. This data will either be provided or transmitted at the time of shipment to retailers, wholesalers or original equipment vehicle manufacturers. Tire identification code and data may be used for error proofing, determining the tire specifications or supporting any inquiries that occur for the duration of its automotive life.

Standard

FIELD CORRELATED LIFE TEST SUPPLEMENT TO SAE/USCAR-2

2001-12-01

HISTORICAL

USCAR20

This life test for underhood/passenger/trunk connector systems may be used in place of Section 5.8.6 (Connector System Electrical Test Flow Chart) of SAE/USCAR-2. All other requirements of SAE/USCAR-2 remain applicable even when this test is used. Refer to SAE/USCAR-2 and Connector/Terminal Supplier for appropriate power rating and current cycle Testing.

Standard

FIELD CORRELATED LIFE TEST SUPPLEMENT TO SAE/USCAR-2

2022-03-15

CURRENT

USCAR20-2

This life test for underhood/passenger/trunk connector systems may be used in place of Section 5.9.6, Connection System Electrical Table of SAE/USCAR-2. All other requirements of SAE/USCAR-2 remain applicable even when this test is used. Refer to SAE/USCAR-2 and Connector/Terminal Supplier for appropriate power rating and current cycle Testing.

Standard

FIELD CORRELATED LIFE TEST SUPPLEMENT TO SAE/USCAR-2

2004-06-23

HISTORICAL

USCAR20-1

This life test for underhood/passenger/trunk connector systems may be used in place of Section 5.9.6, Connection System Electrical Table of SAE/USCAR-2. All other requirements of SAE/USCAR-2 remain applicable even when this test is used. Refer to SAE/USCAR-2 and Connector/Terminal Supplier for appropriate power rating and current cycle Testing.

Standard

TORQUE-TENSION TESTING AND EVALUATION OF FASTENER FINISHES

2020-11-19

CURRENT

USCAR11-2

This standard provides a test method for determining the torque-tension relationship of a fastener finish as applied to a surrogate screw for the purpose of measuring the frictional characteristic of the fastener finish. The results obtained by this test shall be used as a process control attribute of the fastener finish and shall not be utilized for specific applications.

Standard

STANDARD FOR IN-TANK ELECTRIC FUEL PUMPS

1999-08-15

HISTORICAL

USCAR13

This standard covers the operational characteristics, environment, durability procedures, and test procedures for in-tank electric fuel pumps for automotive gasoline applications. Specific performance and test criteria used in conjunction with this procedure are specified on the pump drawing. Particular sections of this document may be required for all applications. This standard is intended to evaluate specific characteristics as a supplement to normal material inspections, dimensional checking, and in-process controls, and should in no way adversely influence other inspection operations.

Standard

TEST PROCEDURE FOR ELECTRICAL GROUND ATTACHMENTS

2022-02-25

HISTORICAL

USCAR26

This test procedure is intended to evaluate and/or validate electrical ground schemes for use on the body or chassis. There are two classes based on the expected environmental conditions. Exposed Grounds can be located anywhere in the vehicle (except on the powertrain) and is the class for which most schemes should be tested. Unexposed Grounds can only be used in the passenger compartment or trunk and as such are special cases. This procedure as written is not intended for testing powertrain grounds where high temperatures and vibration levels may be encountered. These situations may require modifications to this procedure and are left to the Responsible Engineer to determine. This specification does not specifically address validation of terminal to wire electrical crimps. Crimps are tested to SAE/USCAR-21

Standard

Dimensional and Performance Specification for After-Market Gasoline Engine Oil Filters

2013-01-30

HISTORICAL

USCAR36

This specification defines the dimensional and performance requirements for aftermarket spin-on oil filters intended for use on gasoline engines. Filters meeting this specification may also be suitable for use on some diesel applications. Filters meeting these dimensional limits are intended to meet the oil filter fit and package requirements for engine and vehicle designs. Filters meeting the performance requirements are intended to maintain sufficient durability to support many of the OEM's recommended oil change intervals. Some OEM engines may require special filters for which this specification would not support.

Standard

DIMENSIONAL AND PERFORMANCE SPECIFICATION FOR AFTER-MARKET GASOLINE ENGINE OIL FILTERS

2021-05-13

CURRENT

USCAR36-1

This specification defines the dimensional and performance requirements for aftermarket spin-on oil filters intended for use on gasoline engines. Filters meeting this specification may also be suitable for use on some diesel applications. Filters meeting these dimensional limits are intended to meet the oil filter fit and package requirements for engine and vehicle designs. Filters meeting the performance requirements are intended to maintain sufficient durability to support typical 10000 mile oil change intervals. Some OEM engines may require special filters for which this specification would not support. Filters that meet or exceed this specification requirements for both dimensional and performance can claim “Conformance to SAE/USCAR - 36 Specifications.” Filters that meet just the performance specifications (ie. may have different thread) can claim “Aligns to SAE/USCAR - 36 Performance Specifications.”

Standard

Initiator Technical Requirements and Validation

2005-06-06

CURRENT

USCAR28

This specification establishes the design, performance, and validation requirements for the initiator assembly used in airbag modules, seatbelt pretensioners and/or any other Electro-Explosive Devices (EED).

Standard

Automotive Grade Coaxial Cable Performance Specification

2006-01-02

HISTORICAL

USCAR29

This document specifies dimensional, functional and visual requirements for Automotive grade coaxial cable. This material will be designated AG for general-purpose automotive applications or AG LL for low loss applications. It is the responsibility of the user of this cable to verify the suitability of the selected product (based on dimensional, mechanical, electrical and environmental requirements) for its intended application. It is the responsibility of the supplier to retain and maintain records as evidence of compliance to the requirements detailed in this standard.

Standard

Shipping Caps, Torque Caps, and Body Plugs Ergonomic Design Criteria

2015-03-30

CURRENT

USCAR43

This document describes the design and assembly force guidelines for conventional shipping caps, torque caps, and body plugs. All possible design and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the-shelf” design, always consult the responsible Ergonomics Department.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2017-05-10

HISTORICAL

USCAR44

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises a) from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray and different thicknesses of the holes that the clip is inserted into.

Standard

PERFORMANCE SPECIFICATION FOR AUTOMOTIVE WIRE HARNESS RETAINER CLIPS

2021-01-20

HISTORICAL

USCAR44-1

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector in a specific position. Typical plastic retainers work by having a set of “branches” that can be inserted into a hole sized to be easy to install but provide acceptable retention. This specification tests retainer clips for mechanical retention when exposed to the mechanical and environmental stresses typically found in automotive applications over a 15-year service life. This specification has several test options to allow the test to match to the expected service conditions. The variability of applications typically arises from different ambient temperatures near the clip, different proximity to automotive fluids, different exposure to standing water or water spray, and different thicknesses of the holes that the clip is inserted into.