Search Results

Standard

High Temperature Materials for Exhaust Manifolds

1999-08-01

HISTORICAL

J2515_199908

A subcommittee within SAE ISTC Division 35 has written this report to provide automotive engineers and designers a basic understanding of the design considerations and high temperature material availability for exhaust manifold use. It is hoped that it will constitute a concise reference of the important characteristics of selected cast and wrought ferrous materials available for this application, as well as methods employed for manufacturing. The different types of manifolds used in current engine designs are discussed, along with their range of applicability. Finally, a general description of mechanical, chemical, and thermophysical properties of commonly-used alloys is provided, along with discussions on the importance of such properties.

Standard

Infrared Testing

2018-01-09

CURRENT

J359_201801

The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references.

Standard

INFRARED TESTING

1991-02-01

HISTORICAL

J359_199102

The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references.

Standard

VALVE GUIDE INFORMATION REPORT

1993-09-10

HISTORICAL

J1682_199309

This SAE Information Report provides: a Types of valve guides and their nomenclature b Valve guide alloy designations and their chemistries c Valve guide alloy metallurgy d Typical mechanical and physical properties of guide alloys e Typical dimensional tolerances of valve guides and their counterbores f Recommended interference fits g Installation procedures h Application considerations

Standard

Cleanliness Rating of Steels by the Magnetic Particle Method

2018-01-09

CURRENT

J421_201801

This SAE Recommended Practice provides a rating procedure for the cleanliness rating of steels by the magnetic particle method. The procedure is based on counting the number of indications (frequency) and employs a weighted value to obtain a severity factor. The method outlined is similar to that described in SAE Aerospace Material Specification AMS 2301.

Standard

CLEANLINESS RATING OF STEELS BY THE MAGNETIC PARTICLE METHOD

1977-11-01

HISTORICAL

J421B_197711

This SAE Recommended Practice provides a rating procedure for the cleanliness rating of steels by the magnetic particle method. The procedure is based on counting the number of indications (frequency) and employs a weighted value to obtain a severity factor. The method outlined is similar to that described in SAE Aerospace Material Specification AMS 2301.

Standard

CLEANLINESS RATING OF STEELS BY THE MAGNETIC PARTICLE METHOD

1993-05-01

HISTORICAL

J421_199305

This SAE Recommended Practice provides a rating procedure for the cleanliness rating of steels by the magnetic particle method. The procedure is based on counting the number of indications (frequency) and employs a weighted value to obtain a severity factor. The method outlined is similar to that described in SAE Aerospace Material Specification AMS 2301.

Standard

CHEMICAL COMPOSITIONS, MECHANICAL PROPERTY LIMITS, AND DIMENSIONAL TOLERANCES OF SAE WROUGHT ALUMINUM ALLOYS

1985-08-01

HISTORICAL

J457_198508

Standard

Automotive Austempered Ductile (Nodular) Iron Castings (ADI)

2018-01-09

CURRENT

J2477_201801

This SAE Standard covers the mechanical and physical property requirements for Austempered Ductile Iron (ADI) castings used in automotive and allied industries. Specifically covered are: a Hardness b Tensile Strength c Yield Strength d Elongation e Modulus of Elasticity f Impact Energy g Microstructure In this document SI units are primary and in-lb units are derived. Appendix A provides general information and related resources on the microstructural, chemical and heat treatment requirements to meet the mechanical properties needed for ADI in particular service conditions and applications.

Standard

Automotive Austempered Ductile (Nodular) Iron Castings (ADI)

2004-05-26

HISTORICAL

J2477_200405

This SAE Standard covers the mechanical and physical property requirements for Austempered Ductile Iron (ADI) castings used in automotive and allied industries. Specifically covered are: a Hardness b Tensile Strength c Yield Strength d Elongation e Modulus of Elasticity f Impact Energy g Microstructure In this document SI units are primary and in-lb units are derived. Appendix A provides general information and related resources on the microstructural, chemical and heat treatment requirements to meet the mechanical properties needed for ADI in particular service conditions and applications.

Standard

Automotive Compacted Graphite Iron Castings

2007-12-17

HISTORICAL

J1887_200712

This SAE Standard covers the mechanical and physical requirements for Compacted Graphite Iron (CGI) castings used in automotive and allied industries. Requirements in this document include: a Tensile Strength b Yield Strength c Elongation d Graphite Morphology

Standard

Automotive Compacted Graphite Iron Castings

2018-02-15

CURRENT

J1887_201802

This SAE Standard covers the mechanical and physical requirements for Compacted Graphite Iron (CGI) castings used in automotive and allied industries. Requirements in this document include: a Tensile Strength b Yield Strength c Elongation d Graphite Morphology

Standard

ANODIZED ALUMINUM AUTOMOTIVE PARTS

1985-02-01

HISTORICAL

J399_198502

Automotive parts can be fabricated from either coiled sheet, flat sheet or extruded shapes. Alloy selection is governed by finish requirements, forming characteristics, and mechanical properties. Bright anodizing alloys 5657 and 52521 sheet provide a high luster and are preferred for trim which can be formed from an intermediate temper, such as H25. Bright anodizing alloy 5457 is used for parts which require high elongation and a fully annealed ("0") temper. Alloy 6463 is a medium strength bright anodizing extrusion alloy; Alloy X7016 is a high strength bright anodizing extrusion alloy primarily suited for bumper applications. To satisfy anti-glare requirements for certain trim applications, sheet alloy 5205 and extrusion alloy 6063 are capable of providing the desired low-gloss anodized finish.

Standard

WELDING, BRAZING, and SOLDERING—MATERIALS AND PRACTICES

1976-07-01

HISTORICAL

J1147_197607

Standard

WELDING, BRAZING, AND SOLDERING—MATERIALS AND PRACTICES

1983-06-01

HISTORICAL

J1147_198306

The Joint AWS/SAE Committee on Automotive Welding was organized on January 16, 1974, for the primary purpose of facilitating the development and publication of various documents related to the selection, specification, testing, and use of welding materials and practices, particularly for the automotive and related industries. A secondary purpose is the dissemination of technical information.

Standard

Welding, Brazing, and Soldering - Materials and Practices

2018-01-09

CURRENT

J1147_201801

The Joint AWS/SAE Committee on Automotive Welding was organized on January 16, 1974, for the primary purpose of facilitating the development and publication of various documents related to the selection, specification, testing, and use of welding materials and practices, particularly for the automotive and related industries. A secondary purpose is the dissemination of technical information.

Standard

Surface Texture, Roughness (Ra), Peak Count(Pc), and Mean Profile Spacing, (Rsm) Measurement of Metallic Coated and Uncoated Steel Sheet/Strip to be Formed and/or to be Painted

2017-04-03

CURRENT

J911_201704

This SAE Recommended Practice describes a method for measuring Roughness Average (Ra) and Peak Count (PC) and other variables of the surface of metallic coated and uncoated steel sheet/strip.

Standard

BEARING AND BUSHING ALLOYS

1974-10-01

HISTORICAL

J460E_197410

Standard

WROUGHT NICKEL AND NICKEL-RELATED ALLOYS

1976-07-01

HISTORICAL

J470_197607

This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.

Standard

Wrought Nickel and Nickel-Related Alloys

2018-02-15

CURRENT

J470_201802

This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.