Search Results

Standard

AS81936/3 Bearing, Plain, Self Aligning, Cu-Ni-Sn Ball, CRES Race (With Grooved Race) -65F to +350F

2014-09-30

WIP

AS81936/3

This SAE Aerospace Standard will cover airframe plain spherical bearings ustilizing a Copper Nickel Tin ball and a Corrosion Resistant Steel outer race for use between -65F and+350F.

Standard

Bearing, Plain, Self Aligning, Cu-Ni-Sn Ball, CRES Race (Chamfered Race) -65F to +350F

2014-09-30

WIP

AS81936/4

This SAE Aerospace Standard will cover airframe plain spherical bearings ustilizing a Copper Nickel Tin ball and a Corrosion Resistant Steel outer race for use between -65F and+350F.

Standard

BEARINGS, PLAIN, ROD END, SELF-ALIGNING, SELF-LUBRICATING,GENERAL SPECIFICATION FOR (-65 to +250°F)

2012-04-20

WIP

AS8948

inital release.

Standard

ARP5448/10 Plain Bearing, Rod End, Axial Static Proof Load Test Methods

2018-10-09

WIP

ARP5448/10

Define the test methods for performing the axial static proof load test as required in Aerospace Standard AS81935.

Standard

BEARING, PLAIN ROD END, SELF-ALIGNING,SELF-LUBRICATING, WIDE, INTERNALLY THREADED, -65 TO +250 °F

2012-04-20

WIP

AS21243

initial release

Standard

BEARING, PLAIN, ROD END, SELF-ALIGNING, SELF-LUBRICATING,WIDE, EXTERNALLY THREADED,-65 TO +250F

2012-04-20

WIP

AS21242

initial release

Standard

Bearings, Elastomeric General Specification for

2021-02-11

CURRENT

AS85598

This standard defines general requirements for spherical, radial-journal, conical, and thrust bearings which are of laminated elastomeric construction. These bearings are for use in an environment having a temperature spectrum of -65 to +160 °F while reacting steady state loads in addition to oscillating loads and motions. The operating temperature range of -65 to +160 °F reflects the current temperature range for existing parts, but allows for expansion in the future.

Standard

Bearings, Plain, Self-Lubricating, Self- Aligning, High Speed Oscillation -65 to +160 °F

2015-10-27

WIP

AS81819/1B

No scope available.

Standard

Rod End Locking Device Selection Criteria

2020-07-01

CURRENT

ARP6910

This ARP discusses common rod end locking devices with recommended applications and some of the advantages and disadvantages of specific configurations. An appendix is included with factors to be considered for selection of positive locking devices and a discussion of safetying devices for rod end assemblies.

Standard

Bearing, Sleeve, Plain, Self-Lubricating -65 to 250 °F

2017-04-18

WIP

AS21240A

Scope unavailable.

Standard

Plain Bearing High Speed Oscillation Test

2022-09-27

WIP

ARP5448/2A

This test method outlines a standard procedure for performing cyclic reversing load testing on oscillating sliding bearings. The wear data from these tests is to be used for qualification requirements and to establish bearing design criteria.

Standard

Plain Bearing Wear Measurement

2023-03-13

WIP

ARP5448/7B

This standard details two methods of inspecting PTFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the dynamic test. The two methods described are: a. Destructive Inspection - Cut and measure (not applicable to molded liners) b. Nondestructive Inspection - Radial play (gauge) measurement

Standard

Bearings, Plain, Self-Aligning, Self-Lubricating, High Speed Oscillation -65 to +160 °F General Specification For

2021-03-03

WIP

AS81819B

This standard covers the requirements for spherical, self-aligning, self-lubricating bearings which are for use in the ambient temperature range -65 to +160 °F (-54 to +71 °C) at high cyclic speeds. The scope of the standard is to provide a liner system qualification procedure for helicopter sliding bearings defined and controlled by source control drawings. Once a liner system is qualified the source-controlled bearings are further tested under application conditions.

Standard

Bearings, Plain, Self-Aligning, Self-Lubricating, High Speed Oscillation -65 to +160 °F General Specification For

2017-11-15

CURRENT

AS81819A

This standard covers the requirements for spherical, self-aligning, self-lubricating bearings which are for use in the ambient temperature range -65 to +160 °F (-54 to +71 °C) at high cyclic speeds. The scope of the standard is to provide a liner system qualification procedure for helicopter sliding bearings defined and controlled by source control drawings. Once a liner system is qualified the source-controlled bearings are further tested under application conditions.

Standard

Bearings, Plain, (Self-Aligning, Sleeve and Thrust) Self-Lubricating, High Speed Oscillation General Specification For

2001-03-01

HISTORICAL

AS81819

This specification covers the requirements for sliding spherical, sleeve, and thrust self-lubricating bearings which are for use in the ambient temperature range -65°F to +160°F at high cyclic speeds.

Standard

BEARING, PLAIN, ROD END, SELF-ALIGNING, SELF-LUBRICATING, WIDE, EXTERNALLY THREADED, STEEL, CORROSION RESISTANT (CRES) −65 TO +325 °F

2011-06-20

CURRENT

AS81935/6A

Standard

BEARING, PLAIN, ROD END, SELF-ALIGNING, SELF-LUBRICATING, NARROW, EXTERNALLY THREADED, -65 TO +325 °F

2017-10-01

WIP

AS81935/4C

Scope is unavailable.

Standard

BUSHING, SLEEVE, PLAIN INNER BORE LINER

2021-09-21

CURRENT

AS6072A

Standard

Bearings, Sleeve, Plain and Flanged, Self-Lubricating -65 to +250 °F

2017-04-04

WIP

AS8943A

This standard covers plain and flanged sleeve bearings which are self-lubricating by incorporating polytetrafluoroethylene (PTFE) in a liner in the bore for use in a temperature range of -65 to +250 ˚F (-54 to +121 °C).

Standard

Bearings, Sleeve, Plain and Flanged, Self – Lubricating -65 to +250 °F

2010-08-13

CURRENT

AS8943

This standard covers plain and flanged sleeve bearings which are self-lubricating by incorporating polytetrafluoroethylene (PTFE) in a liner in the bore for use in a temperature range of -65 to +250 °F (-54 to +121 °C).