Refine Your Search

Date

Date

Topic

Topic

Automatic Transmission and Transaxle Committee Electrical, Electronics, and Avionics Analysis methodologies

Search Results

Viewing 1 to 20 of 27
12Next >Last >>
Sort by published
Standard

SYMBOLS FOR HYDRODYNAMIC DRIVES
1988-06-01
HISTORICAL
J640_198806
The following system of symbols is recommended for use in technical papers and engineering reports dealing with hydrodynamic drives.
Standard

Symbols for Hydrodynamic Drives
2000-03-10
HISTORICAL
J640_200003
The following system of symbols is recommended for use in technical papers and engineering reports dealing with hydrodynamic drives.
Standard

Automatic Transmissions—Manual Control Sequence
2007-10-22
HISTORICAL
J915_200710
The scope and purpose of this SAE Recommended Practice is to provide a standard pattern or sequence for the manual control of automatic transmissions in passenger cars and light-duty trucks. This generally refers to left hand drive mechanical shift applications.
Standard

Automatic Transmissions - Manual Control Sequence
2017-03-09
CURRENT
J915_201703
The scope and purpose of this SAE Recommended Practice is to provide a standard pattern or sequence for the manual control of automatic transmissions in passenger cars and light-duty trucks. This generally refers to left hand drive mechanical shift applications.
Standard

AUTOMATIC TRANSMISSIONS—MANUAL CONTROL SEQUENCE
1993-04-01
HISTORICAL
J915_199304
The scope and purpose of this SAE Recommended Practice is to provide a standard pattern or sequence for the manual control of automatic transmissions in passenger cars and light-duty trucks.
Standard

Automatic Transmissions—Manual Control Sequence
2000-11-02
HISTORICAL
J915_200011
The scope and purpose of this SAE Recommended Practice is to provide a standard pattern or sequence for the manual control of automatic transmissions in passenger cars and light-duty trucks.
Standard

Low-Speed Continuous Slip Durability Test
2022-11-22
CURRENT
J3210_202211
This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. This SAE No. 2 friction test monitors the µ-v curve for a negative slope which can be used to evaluate a wet clutch system (WCS) anti-shudder performance and can be used for any wet driveline mechanism. WCS shudder is considered a clutch failure condition. The cause of shudder is consistent with glazing as the primary failure mode. It has been shown that a substantial loss of the wet friction material surface porosity leads to a glaze forming on the friction material surface. This process typically leading to a negative dµ/dv slope over time as addressed in SAE 2020-01-0560.
Standard

Automatic Transmission Intake Filter Test Procedure
2021-06-22
CURRENT
J2312_202106
This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Section 5 include a variety of tests and alternative tests that are not applicable to all filters and applications, so the engineer must specify which tests are to be performed for a particular application. These test procedures are intended to evaluate filter functional performance characteristics only, durability is not evaluated under this standard. Filter design requirements must be specified by the engineer on the filter assembly drawing, an applicable engineering specification, or summarized on an application data sheet similar to that found in this recommended practice. See Figure 6. Pressure circuit filters, both barrier and system contamination control types, are not covered under this standard.
Standard

PARK STANDARD FOR AUTOMATIC TRANSMISSIONS
1993-06-01
HISTORICAL
J2208_199306
To provide a Recommended Practice for validating the function and integrity of an automatic transmission park mechanism with its associated control system and environment.
Standard

Park Standard for Automatic Transmissions
2007-10-22
HISTORICAL
J2208_200710
To provide a Recommended Practice for validating the function and integrity of an automatic transmission park mechanism with its associated control system and environment.
Standard

Park Standard for Automatic Transmissions
2016-05-26
CURRENT
J2208_201605
To provide a Recommended Practice for validating the function and integrity of an automatic transmission park mechanism with its associated control system and environment.
12Next >Last >>
X