Search Results

The influence of a large truck on the aerodynamics of a small passenger car in an overtaking manoeuvre on the motorway was considered, many years ago, during the 1970's, to be a potential problem for the vehicle aerodynamicist. The concern never became significant as vehicle architecture evolved and car weights increased. The current drive for improved fuel economy is advocating that a considerable reduction in vehicle mass is desirable and therefore it may be time to readdress the significance of the truck passing manoeuvre. A quasi-steady experiment has been undertaken at small model scale to examine the aerodynamic characteristics of a small car in proximity to a large truck. Measurements at yaw were included to crudely simulate the effects of a crosswind. The wind tunnel data is presented and the limitations of the experimental procedure are discussed.

In the wind tunnel the effect of a wind input on the aerodynamic characteristics of any road vehicle is simulated by yawing the vehicle. This represents a wind input where the wind velocity is constant with height above the ground. In reality the natural wind is a boundary layer flow and is sheared so that the wind velocity will vary with height. A CFD simulation has been conducted to compare the aerodynamic characteristics of a DrivAer model, in fastback and squareback form, subject to a crosswind flow, with and without shear. The yaw simulation has been carried out at a yaw angle of 10° and with one shear flow exponent. It is shown that the car experiences almost identical forces and moments in the two cases when the mass flow in the crosswind over the height of the car is similar. Load distributions are presented for the two cases. The implications for wind averaged drag are discussed.

Vehicles on the road operate in the turbulent flow field resulting from the combined effects of the natural wind and the wakes of other vehicles. While substantial data exists on the properties of the natural wind, much less information is available for the wake properties of road vehicles. The wake information available for road vehicle shapes is mainly restricted to the near wake region, but to understand the vehicle operating environment it is the wake downstream of this region which is of interest. To determine the range of this area of interest requires some knowledge of the decay of the wake properties. From wind tunnel studies using small simple bluff bodies in free stream and in ground proximity the principle wake properties, velocity deficit and peak turbulence intensity have been measured. The maximum velocity deficit is shown to approximately decay with x-2/3, where x is the distance downstream, while turbulence intensity decays at a slightly slower rate.

Various studies have shown that the level of wind noise experienced inside cars on the road in unsteady conditions can be substantially different from that measured in wind tunnel tests conducted using a low turbulence facility. In this paper a simple geometric body representing the cabin of a passenger car has been used to investigate the effects of free stream turbulence, (FST), on the A-pillar vortex flowfield and the side glass pressure distribution. Beneath the A-pillar vortex, both mean and dynamic pressures are increased by FST. The unsteady pressure can be associated with wind noise and the flow visualization shows the peak unsteadiness is related to the separation of the secondary vortex.

Aerodynamic aids, such as spoilers, applied to the rear of cars can provide drag reduction to improve performance, or can enhance high speed stability by reducing lift at the rear axle. In some cases these can be conflicting demands. It has been noted, however, that when rear axle lift is reduced there is often a reduction in yawing moment which has a beneficial effect on crosswind sensitivity. Wind tunnel results from real road vehicles are presented to illustrate this effect. This beneficial relationship is further explored in a wind tunnel experiment using simple models to represent road vehicles. Force and moment coefficients as a function of yaw angle are measured for a range of vehicle geometries which generate a substantial variation in lift. It is shown that as lift is reduced, yawing moment is also reduced, while side force and rolling moment are increased.

Road vehicles operate almost entirely in the unsteady conditions created by the natural wind and the wakes of other vehicles. This is a time dependent and turbulent environment, which differs noticeably from the conditions simulated in the wind tunnel. Using a quasi-steady analysis the aerodynamic characteristics, as determined from wind tunnel tests, are used to derive the unsteady aerodynamic loads experienced by a typical road vehicle subjected to a random wind input. For this paper the wind energy spectrum is of the von Karman type and isotropic turbulence is assumed. The effects of vehicle speed, wind speed and wind direction on lift and side force spectra are presented.

Growing concerns about the environmental impact of road vehicles will lead to a reduction in the aerodynamic drag for all passenger cars. This includes Sport Utility Vehicles (SUVs) and light trucks which have relatively high drag coefficients and large frontal area. The wind tunnel remains the tool of choice for the vehicle aerodynamicist, but it is important that the benefits obtained in the wind tunnel reflect improvements to the vehicle on the road. Coastdown measurements obtained using a Land Rover Freelander, in various configurations, have been made to determine aerodynamic drag and these have been compared with wind tunnel data for the same vehicle. Repeatability of the coastdown data, the effects of drag variation near to zero yaw and asymmetry in the drag-yaw data on the results from coastdown testing are assessed. Alternative blockage corrections for the wind tunnel measurements are examined.

Wind tunnel tests have been conducted on a simple bluff body model, representing a car like shape, to investigate drag reduction opportunities from injecting low velocity air into the base region. This flow is known as base bleed. Most tests have been carried out using a square back shape. The effects of flow rate, porosity and porosity distribution over the base area have been investigated. In all cases drag is reduced with increasing bleed rate, but the optimum porosity is a function of bleed rate. A significant part of the drag reduction occurs without the bleed flow and arises from the presence of a cavity in the model. The effects of cavity size are examined for different base configurations. Some factors affecting implementation are considered.

It has been recognised that the ideal flow conditions that exist in the modern automotive wind tunnel do not accurately simulate the environment experienced by vehicles on the road. This paper investigates the effect of varying one flow parameter, freestream turbulence, and a single shape parameter, leading edge radius, on aerodynamic drag. The tests were carried out at model scale in the Loughborough University Wind Tunnel, using a very simple 2-box shape, and in the MIRA Full Scale Wind Tunnel using the MIRA squareback Reference Car. Turbulence intensities up to 5% were generated by grids and had a strong effect on transcritical Reynolds number and Reynolds sensitivity at both model scale and full scale. There was a good correlation between the results in both tunnels.

With increasing speeds and the anticipated reduction in weight of modern cars, the issue of crosswind sensitivity is becoming increasingly important. In a previous paper by the same authors, the normal method of testing such aerodynamic characteristics at model scale, using static models at yaw to the freestream, was compared with dynamic testing, in which the model is propelled across a ‘gust’ simulated by a wind tunnel. A direct comparison using a similar gust profile for both static and dynamic tests was made with the conclusion that the simple static test technique was underestimating the true transient loads. Further tests have been carried out, on a generic squareback (or estate) model, during which the effect of varying both the vertical velocity profile and the turbulence intensity within the gust was considered.

The aerodynamic development of cars is conventionally carried out in the wind tunnel with the working section floor representing the ground surface. While recognising that the boundary conditions are false it has generally been assumed that this basic ground simulation is adequate for road cars. This situation is currently being reappraised. In this investigation a simple 1/4 scale car model has been tested in the MIRA Model Wind Tunnel, using both moving and stationary belt to represent the ground surface. The body and wheel drag contributions were measured independently. The influence of rear body shape, front spoilers, cooling airflow, and underfloor roughness on the aerodynamic characteristics, for both ground conditions has been assessed.

A drag coefficient, which is representative of the drag of a car undergoing a particular drive cycle, known as the cycle-averaged-drag coefficient, has been previously developed. It was derived for different drive cycles using mean values for the natural wind. It assumed terrain dependent wind velocities based on the Weibull function, equi-probable wind direction and shear effects. It did not, however, include any effects of turbulence in the natural wind. Some recent research using active vanes in the wind tunnel to generate turbulence has suggested that the effect on drag can be evaluated from the quasi steady wind inputs. On this basis a simple quasi-steady theory for the effect of turbulence on car drag is developed and applied to predicting the cycle-averaged-drag coefficient for a range of cars of different types. The drag is always increased by the turbulence but in all cases is relatively small.

A 3D Navier-Stokes CFD model of a wheel located within a wheelhouse cavity has been produced. Both a stationary wheel on a fixed ground and a rotating wheel on a moving ground were considered. Extensive comparisons with the results of a wind tunnel investigation based on the same geometry are presented. These consist of three force coefficients and pressures on the internal faces of the cavity. Comparison with the experimental results gave encouraging agreement. It was found that the rotating wheel produced more drag than the stationary wheel whilst shroud drag decreased when the groundplane was moving compared to when it was stationary.

The effects of adding a streamlined tail to a simple vehicle shape, represented by the Windsor Body has been investigated in a small scale wind tunnel experiment. The extended tail has a constant width, with a flat lower surface and a constant upper surface taper angle. The tail is truncated in steps to understand the trends in the principal aerodynamic characteristics. The slant surface and the base have been pressure tapped to indicate the contribution to drag and lift from these surfaces. The bodies have been tested over a range of yaw angles and wind tunnel airspeeds. The effects of adding wheels, albeit in a fixed ground experiment, has also been studied. The experimental data for the basic wheel-less body in a squareback configuration and with tapered tails of different length at zero yaw has been compared with an earlier CFD simulation of the same configurations.