Refine Your Search

Date

Date

Topic

Topic

Radio equipment Military vehicles and equipment Failure analysis AE-8A Elec Wiring and Fiber Optic Interconnect Sys Install Connecting rods

Search Results

Viewing 1 to 20 of 27
12Next >Last >>
Sort by published
Standard

Design and Handling Guide Radio Frequency Absorptive Type Wire and Cables (Filter Line, MIL-C-85485)
2012-12-11
HISTORICAL
AIR4465
This document presents design and application information which will allow optimized utilization of filter line wire and cable purchased to MIL-C-85485. Filter line wire is defined and design information is presented. The electrical and mechanical performance characteristics of the wire along with recommended harnessing methods and techniques are also presented.
Standard

Design and Handling Guide Radio Frequency Absorptive Type Wire and Cables (Filter Line, AS85485)
2020-01-31
CURRENT
AIR4465A
This document presents design and application information which will allow optimized utilization of filter line wire and cable purchased to AS85485. Filter line wire is defined and design information is presented. The electrical and mechanical performance characteristics of the wire, along with recommended harnessing methods and techniques, are also presented.
Standard

EWIS Wiring Insulation Breakdown Testing
2022-09-30
CURRENT
ARP6216
This SAE Aerospace Recommended Practice (ARP) identifies the minimum requirements for the testing of insulated electrical wiring for on-aircraft, aeronautical and aerospace applications. The testing requirements defined herein, ensure that a wire fault can be found safely when using a high potential voltage tester (hipot). This test is intended to aid in finding a breach in the wire insulation, and not for the identification of the resistance of the insulation. The test method defined herein is limited to equipment which ia able to control and limit the DC output to 1500 VDC maximum. This type of wire dielectric tester is typically designed to trip on current leakage and not necessarily on arc detection. This test method is solely designed to identify gross/large wire insulation damage or degradation. For additional related information on this topic and related test methods, refer to the documents cited in Section 2.
Standard

Hot Stamp Wire Marking Concerns for Aerospace Vehicle Applications
2017-01-24
CURRENT
AIR5575A
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
Standard

Hot Stamp Wire Marking Concerns for Aerospace Vehicle Applications
2009-01-15
HISTORICAL
AIR5575
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
Standard

Aerospace Vehicle Wiring, Lessons Learned
2024-03-04
CURRENT
AIR6808A
This AIR is limited to the requirements of AS50881 and examines these requirements, providing rationale behind them. AS50881 is only applicable to the aircraft EWIS. Pods and other devices that can be attached to an aircraft are considered as part of the aircraft equipment design. Its scope does not include wiring inside of airborne electronic equipment but does apply to wiring externally attached to such equipment. The AS50881 scope does not include attached devices but does include the interface between the pod/equipment and aircraft wiring. Section 3.3.5 addresses components such as antennas and other similar equipment that were once supplied as Government Furnished Aeronautical/Aerospace Equipment (GFAE).
Standard

Aerospace Vehicle Wiring, Lessons Learned
2020-04-16
HISTORICAL
AIR6808
This SAE Aerospace Information Report (AIR) is limited to the requirements of AS50881 and examines these requirements, providing rationale behind them. AS50881 is only applicable to the aircraft electrical wiring and interconnect system (EWIS). Pods and other devices that can be attached to an aircraft are considered as part of the aircraft equipment design. Its scope does not include wiring inside of airborne electronic equipment, but does apply to wiring externally attached to such equipment. The AS50881 scope does not include attached devices but does include the interface between the pod/equipment and aircraft wiring. 3.3.5 addresses components such as antennas and other similar equipment that were once supplied as Government Furnished Aeronautical/Aerospace Equipment (GFAE).
12Next >Last >>
X