Search Results

NVH quality is one of the most important criteria by which people judge the design of a vehicle. The Powertrain Mounting System (PMS), which can reduce the vibration from engine to vehicle cab as well as the inside noise, has attained significant attention. Much research has been done on the isolation method for three- and four-point mounting. But the six-point mounting system, which is usually equipped in commercial vehicle, is seldom studied and should be paid more attention. In this paper, the support rod installed on the upside of the transmission case is considered as a flexible body. Thus a rigid-flexible coupling model of PMS is established and the necessity of the established model is analyzed by comparing the simulation results of the new model and those of the conventional model.

The ride comfort of the commercial vehicle is mainly affected by several vibration isolation systems such as the primary suspension system, engine mounting system and the cab mounting system. A rigid-flexible coupling model for the truck was built and analyzed in multi-body environment (ADAMS). The method applying the excitation on the wheels center and the engine mountings in time domain was presented. The variables' effects on the ride performance were studied by design of experiment (DOE). The optimal design was obtained by the co-simulation of the ADAMS/View, iSIGHT and Matlab. It was found that the vertical root mean square (RMS) acceleration and frequency-weighted RMS acceleration on the seat track were reduced about 17% and 11% respectively at different speeds relative to baseline according to ISO 2631-1.

The suspension system of a heavy truck's driver seat plays an important role to reduce the vibrations transmitted to the seat occupant from the cab floor. Air-spring is widely used in the seat suspension system, for the reason that its spring rate is variable and it can make the seat suspension system keep constant ‘tuned’ frequency compared to the conventional coil spring. In this paper, vibration differential equation of air-spring system with auxiliary volume is derived, according to the theory of thermodynamic, hydrodynamics. The deformation-load static characteristic curves of air-spring is obtained, by using a numerical solution method. Then, the ADAMS model of the heavy truck's driver seat suspension system is built up, based on the structure of the seat and parameters of the air-spring and the shock-absorber. At last, the model is validated by comparing the simulation results and the test results, considering the seat acceleration PSD and RMS value.

In this paper, a new computational method is provided to identify the uncertain parameters of Load Sensing Proportional Valve (LSPV) in a heavy truck brake system by using the polynomial chaos theory. The simulation model of LSPV is built in the software AMESim depending on structure of the valve, and the estimation process is implemented relying on the experimental measurements by pneumatic bench test. With the polynomial chaos expansion carried out by collocation method, the output observation function of the nonlinear pneumatic model can be transformed into a linear and time-invariant form, and the general recursive functions based on Newton method can therefore be reformulated to fit for the computer programming and calculation. To improve the estimation accuracy, the Newton method is modified with reference to Simulated Annealing algorithm by introducing the Metropolis Principle to control the fluctuation during the estimation process and escape from the local minima.

Nowadays, studying the human body response in a seated position has attracted a lot of attention as environmental vibrations are transferred to the human body through floor and seat. This research has constructed a multi-body biodynamic human model with 17 degrees of freedom (DOF), including the backrest support and the interaction between feet and ground. Three types of human biodynamic models are taken into consideration: the first model doesn't include the interaction between the feet and floor, the second considers the feet and floor interaction by using a high stiffness spring, the third one includes the interaction by using a soft spring. Based on the whole vehicle model, the excitation to human body through feet and back can be obtained by ride simulation. The simulation results indicate that the interaction between feet and ground exerts non-negligible effect upon the performance of the whole body vibration by comparing the three cases.

The dual clutch transmission is one of the possible choices for electric vehicle drivelines. The basic principle and control mode of shifting of wet dual clutch transmission are introduced, and the dynamic process of shifting of wet double clutch transmission is studied. Combined with the dynamic model of the wet clutch engagement process, the difference between the dynamic characteristics of the dual clutch transmission modeling using the Coulomb friction model and the dual-clutch transmission model using the average flow model and the micro-convex contact theory is analyzed. The shift control strategy of the dual clutch transmission proposes a correction method to improve the shifting smoothness. Studies have shown that the torque response of the wet clutch has significant hysteresis, and the improved control algorithm can significantly improve the shifting smoothness of the wet dual clutch transmission.

This paper investigates a hierarchical optimization procedure for the optimum synthesis of a double-axle steering mechanism by considering the dynamic load of a vehicle which is seldom discussed in the previous literature. Firstly, a multi-body model of double-axle steering is presented by characterizing the detailed leaf spring effect. Accordingly, the influences of dynamic load including the motion interference of steering linkage resulted from the elastic deformation of leaf spring, and the effects of wheel slip angle and the position discrepancy of wheel speed rotation centers are explored systematically. And then, a hierarchical optimization method based on target cascading methodology is proposed to classify the design variables of double-axle steering mechanism into four levels. At last, a double-axle steering mechanism of a heavy-duty truck is utilized to demonstrate the validity of this method.

To design and optimize the vehicle driveline is necessary to decrease the fuel consumption and improve dynamic performance. This paper describes a methodology to optimize the driveline design including the axle ratio, transmission shift points and transmission shift ratios considering uncertainty. A new and flexible tool for modeling multi-domain systems, Modelica, is used to carry out the modeling and analysis of a vehicle, and the multi-domain model is developed to determine the optimum design in terms of fuel economy, with determinability. Secondly, a robust optimization is carried out to find the optimum design considering uncertainty. The results indicate that the fuel economy and dynamic performance are improved greatly.

Hydraulic power steering system, which can reduce the steering hand force by applying the output from a hydraulic actuator, has been widely used in vehicles. In this paper, a detailed steer model including steering column, steering trapezium, and detailed hydraulic power steering system which is consisting of steering cylinder, relief valve, rotary valve, pump and hydraulic lines were established, and a multi-body model of a heavy truck was established to connect with the hydraulic power steering system. Modelica simulation language, which can be efficiently used to investigate multi-domain problems, was used to in the modeling and simulation of the power steering system and the vehicle. The simulation was carried out to identify the effects of design variables on the lateral stability of the vehicle. The application of Modelica for investigating multi-domain problems is also demonstrated.

Three constitutive models which capture the amplitude and frequency dependency of filled elastomers are implemented for the conventional engine mounts of automotive powertrain mounting system (PMS). Firstly, a multibody dynamic model of a light duty truck is proposed, which includes 6 degrees of freedom (DOFs) for the PMS. Secondly, Three constitutive models for filled elastomers are implemented for the engine mounts of the PMS, including: (1) Model 1: Kelvin-Voigt model; (2) Model 2: Fractional derivative Kelvin-Voigt model combined with Berg’s friction; (3) Model 3: Generalized elastic viscoelastic elastoplastic model. The nonlinear behaviors of dynamic stiffness and damping of the mounts are investigated. Thirdly, simulations of engine vibration dynamics are presented and compared with these models and the differences between common Kelvin-Voigt model and other constitutive models are observed and analyzed.

Steering returnability is an important index for evaluating vehicle handling performance. A systematic method is presented in this paper to reduce the high yaw rate residue and the steering response time for a light duty truck in the steering return test. The vehicle multibody model is established in ADAMS, which takes into consideration of the frictional loss torque and hydraulically assisted steering property in the steering mechanism, since the friction, which exists in steering column, spherical joint, steering universal joint, and steering gear, plays an important role in vehicle returnability performance. The accuracy of the vehicle model is validated by road test and the key parameters are determined by executing the sensitivity analysis, which shows the effect of each design parameter upon returnability performance.

The automatic mechanical transmission (AMT) was designed by automobile manufacturers to provide a better driving experience, especially in cities where congestion frequently causes stop-and-go traffic patterns. It uses electronic sensors, processors, hydraulic or pneumatic actuators execute clutch actuation and gear shifts on the command of the driver. Such systems coupled with various physical domains have great influence on the dynamic behavior of the vehicle, such as shift quality, driveability, acceleration, etc. This paper presents a detailed AMT model composed of various components from multi-domains like mechanical systems (clutch, gear pair, synchronizer, etc.), pneumatic actuator systems (clutch actuation system, gear select actuation system, gear shift actuation system, etc.). Various components and subsystem models, such as the vehicle, engine, AMT, wheels, etc., are integrated into an overall vehicle system model according to the transmission power flow and control logic.

As there are a variety of uncertainty contained in dynamic systems, this paper presents a method to identify the uncertain parameters of Load Sensing Proportional Valve in a heavy truck brake system. This method is derived from polynomial chaos theory and uses the maximum likelihood approach to estimate the most likely value of uncertain parameters, such as equivalent bearing area diameter of the diaphragm, preload of return spring and so on. The maximum likelihood estimates are obtained through minimizing the cost function derived from the prior probability for the measurement noise. Direct stochastic collocation has been shown to be more efficient than Galerkin approach in the simulation of systems with large number of uncertain parameters. The simulation model of Load Sensing Proportional Valve is built in software AMESim based on logic structure of the valve. The uncertain parameters are estimated through the simulation results which are treated as measurements.

To provide a greater weight capacity, the tandem axle which is a group of two or more axles situated close together has been used on most heavy truck. In general, the reaction moments during braking cause a change in load distribution among both axles of the tandem suspension. Since load transfer among axles of a tandem suspension can lead to premature wheel lockup, tandem-axle geometry and the brake force distribution among individual axles of a tandem suspension have a pronounced effect on braking efficiency. The braking efficiency has directly influence on the vehicle brake distance and vehicle travelling direction stability in any road condition, so how to improve the braking efficiency is researched in this paper. The load transfer among individual axles is not only determined by vehicle deceleration but also by the actual brake force of each axle for tandem axle suspension, which increases the difficulty of braking efficiency improving.

Electric vehicles driven by in-wheel-motor have the advantages of compact structure and high transmission efficiency, which is one of the most ideal energy-saving, environmentally friendly, and safe driving forms in the future. However, the addition of the in-wheel-motor significantly increases the unsprung mass of the vehicle, resulting in a decrease in the mass ratio of the vehicle body to the wheel, which will deteriorate the ride comfort and safety of the vehicle. To improve the vibration performance of in-wheel-motor driven vehicles, a semi-active inerter-spring-damper (ISD) suspension with in-wheel-motor (IWM) dynamic vibration absorber (DVA) of the electric wheel is proposed in this paper. Firstly, a structure of in-wheel-motor DVA is proposed, which converts the motor into a dynamic vibration absorber of the wheel to suppress the vibration of the unsprung mass.

For vehicles equipped with dry dual clutch transmission, due to the diversity of starting conditions, it is a nontrivial task for control strategy to meet the requirements of all kinds of complex starting conditions, which is easy to cause large starting shock and serious clutch wear. Therefore, it is proposed in this paper an adaptive control strategy for complex starting conditions by adjusting two clutches to participate in the starting process at the same time. On the basis of establishing the transmission system model and clutch model, the starting conditions are identified in terms of starting speed, road adhesion and driver's intention, in which the driver's intention is identified by fuzzy reasoning model. Based on the identification of starting conditions and considering the safety principle, it is selected the appropriate starting gear and clutch combination mode, and adjusted the combination speed of the two clutches to carry out an adaptive control strategy.

A multibody model for riderless bicycle dynamics considering tire characteristics is presented. A riderless bicycle is regarded as a multibody system consisting of four rigid bodies: rear wheel, frame, front fork, and front wheel. Every two bodies are connected with a revolute joint. The mass center coordinates and Euler angles of the rigid bodies are used as the generalized coordinates to describe their positions and orientations. The system equations of motion are obtained using Lagrange equations of the first kind. Due to the existence of the three revolute constraints and the use of dependent generalized coordinates, the Lagrange multipliers are employed to account for revolute reaction forces. As for the contact between the wheel and the ground, many studies regarded the wheel as a rigid body with a knife edge, which lead to the nonholonomic constraints between the wheel and the ground.

To study the torque distribution of track and tire in the wheel-track hybrid drive vehicle driving along the shoreline, an analysis model of wheel-track hybrid drive vehicle was established by using multi-body dynamics (MBD), discrete element (DEM), and shoreline pavement construction methods. The vehicle speed, acceleration, torque, vertical load, sinkage, slip, and other indicators when the vehicle passes the shoal at different wheel speed of rotation are analyzed. The relationships between wheel speed of rotation and slip, sinkage and slip, and vertical load and driving moment were studied, and the laws that the sinkage of tires and tracks is positively related to their slippage and the driving moment of wheels and tracks is positively related to their vertical load were obtained.

A simulation model of the single cone synchronizer is presented using the dynamic implicit algorithm with commercial Finite Element Analysis (FEA) software Abaqus. The meshing components include sleeve gear, blocking ring and clutch gear, which are all considered as deformation body. The processes mainly contain the contact between sleeve teeth and blocking teeth, meshing period and the impact of sleeve teeth and clutch gear teeth, and these nonlinear contact steps are realized with Abaqus. In addition, a shift force derives from experiment is applied to the sleeve ring, and a moment is added to the clutch gear to realize the relative rotational speed. Based on the FEA model, the effect of the varied frictional coefficients between the cone surfaces of blocking ring and clutch gear on the synchronizer time and contact stress is discussed. Variation of stresses and contact force with respect to time are evaluated from this analysis.

In order to reasonably match the variable stiffness and location of the Powertrain Mounting System (PMS) and optimize the ride comfort of commercial vehicle, a thirteen degrees of freedom (DOF) model of a commercial vehicle was established in Adams/view. Specially, the support rod installed on the upside of the transmission case was modeled as a flexible body. The vibration isolation provided by the PMS was evaluated in three aspects: the energy decoupling of the powertrain, the response force of the mount and the displacement of the powertrain. The energy decoupling ratio, the force RMS of the mount when force excitation was applied on the powertrain and the displacement of the powertrain Center of Gravity (C.G) when displacement excitation was applied on the vehicle chassis were selected as the optimal target. Adams and MATLAB were integrated into the optimization software iSIGHT to optimize the PMS. NSGA-II is used to obtain some Pareto-optimal solutions of PMS.