Search Results

In tire development, the dynamic tire-road contact forces are an important indicator to assess structure-borne interior cabin noise. This type of noise is the dominant source in the frequency range from 50-450 Hz, especially when rolling with constant angular velocity on a rough road. The spatial force distribution is difficult or sometimes even impossible to simulate or measure in practice. So, the use of an inverse technique is proposed. This technique uses response measurements in combination with a digital twin simulation model to obtain the input forces in an inverse way. The responses and model properties are expressed in the time domain, since it is specifically aimed to trace back the impact locations from road surface texture indents on the tire. In order to do so, the transient responses of the travelling waves as a result of these impacts is used. The framework expresses responses as a convolution product of the unknown loads and impulse response measurements.

Maximizing the acoustic attenuation is one of the important design criteria of automotive exhaust systems. Although both analytical and numerical approaches exist to evaluate the acoustic transmission properties of exhaust systems, they are, at present, insufficient to model the full geometrical complexity and to accurately assess the influence of thermal and aerodynamic phenomena onto the acoustic attenuation characteristics. For this reason, an experimental test campaign is often still indispensable to evaluate the aeroacoustic performance of exhaust systems. One of the most commonly used experimental characterization techniques for flow duct systems is the two-port characterization.

The identification of the contributions of airborne noise sources in vehicles in operational driving conditions is still a cumbersome task. Whereas the measurement of the transfer path from possible noise sources to the observer ear locations is efficient and accurate in most conditions, the source strength identification is still a challenging task. This paper presents the basic concepts of a new source quantification technique based on acoustic pressure measurements close to the operating sources. The main goal of developing a new technique is to achieve a faster and more economic method as compared to existing methods.

While CAE methods allow improving nominal product design using virtual prototypes, uncertainty and variability in properties and manufacturing processes lead to scatter in actual performances. Uncertainty must hence be incorporated in the CAE process to guarantee the robustness and reliability of the design. This paper presents an overview of uncertainty-based design in automotive and aerospace engineering. Fuzzy methods take uncertainty into account, whereas reliability analysis and a reliability-based design optimization framework can deal with variability. Key enabling technologies to alleviate the computational burden, such as workflow automation, substructuring and design of experiments, are discussed, and industrial applications are presented.

A key element to bring research advances on intelligent materials to industrial use is that the product CAE models must support such solutions. This involves modeling capabilities for intelligent material systems, sensor and actuator components, control systems as well as their integration in system-level application designs. The final result will then be a multi-attribute optimization approach integrating noise and vibration performance with reliability, durability and cost aspects. As no single integrated solution will fulfill all requirements of the various material and control approaches, the focus of the research is on the use, combination and extension of existing codes and tools.

Despite the fact that Transfer Path Analysis (TPA) is a well known and widely used NVH tool it still has some hindrances, the most significant being the huge measurement time to build the full data model. For this reason the industry is constantly seeking for faster methods. The core concepts of a novel TPA approach have already been published in a paper at the ISMA 2008 Conference in Leuven, Belgium. The key idea of the method is the use of parametric models for the estimation of loads. These parameters are frequency independent as opposed to e.g. the classical inverse force identification method where the loads have to be calculated separately for each frequency step. This makes the method scalable, enabling the engineer to use a simpler model based on a small amount of measurement data for quick troubleshooting or simply increase accuracy by a few additional measurements and using a more complex model.

One dimensional linear acoustics network models are commonly used for the acoustic design of intake and exhaust systems. These models are advantageous since they allow the characterization of the scattering matrices for individual elements, independent of the upstream or downstream components. For an intake or exhaust assembly, the individual elements can be combined by a simple multiplication of the individual matrices to assess the propagation characteristics of the whole system under consideration. The determination of the scattering matrix coefficients can be carried out in an analytical, numerical or experimental way. Since the analytical methodologies are limited to uniform or simplified mean flow representation and the experimental two-port determination is expensive and time-consuming, a numerical method using the time domain Linearized Euler Equations is proposed in this paper.

The development of new design tools to predict the vibro-acoustic behavior within the vehicle development process is of essential importance to achieve better products in an ever shorter timeframe. In this paper, an energy flow post-processing tool for structural dynamic analysis is presented. The method is based on the conversion of conventional finite element (FE) results into energy quantities corresponding with each of the vehicle subcomponents. Based on the global dynamic system behavior and local subcomponent descriptions, one can efficiently evaluate the energy distribution and analyze the vibro-acoustic behavior in complex structures. By using energy as a response variable, instead of conventional design variables as pressure or velocity, one can obtain important information regarding the understanding of the vibro-acoustic behavior of the system.

In many industrial applications, such as in the automotive and machine building industry, there is a continuous push towards lightweight materials motivated by material and energy savings. This increased use of lightweight materials, however, can strongly compromise the Noise, Vibration and Harshness (NVH) performance of the final products. Especially in times where the NVH performance not only receives a higher legislative attention, but also becomes a commercial differentiator, this also represents a key point of attention for designers and directs research activities towards new experimental and numerical techniques to accurately predict the NVH performance of lightweight systems as early as possible in the design process. The presented work discusses novel measurement setup, specifically developed for examining the vibro-acoustic behavior of lightweight structures. The test stand consists of a concrete cavity of 0.83 m₃.

Lightweight structures and designs have been widely used in a number of engineered structures due to ecological and environmental aspects. Nonetheless, lightweight structures typically experience a reduced noise and vibration reduction performance as a consequence of their increased stiffness-to-mass-ratio. To enhance it, novel low mass and compact countermeasures are often sought to address the challenges of achieving not only a good Noise, Vibrations and Harshness (NVH) reduction performance but also maintaining a lightweight design. Recently, locally resonant metamaterials have emerged and shown potential as a lightweight noise and vibration solution with a superior performance in tunable frequency ranges, known as stop bands i.e. frequency regions where free wave propagation is not allowed. These can be achieved by assembling resonant elements that are tuned to the targeted frequency range onto a host structure.

The continuous pursuit for lighter, more affordable and more silent cars, has pushed OEMs into optimizing the design of car components. The different panels surrounding the car interior cavity such as firewall, door or floor panels are of key importance to the NV performance. The design of the sound packages for high-frequency airborne input is well established. However, the design for the mid-frequency range is more difficult, because of the complex inputs involved, the lack of representative performance metrics and its high computational cost. In order to make early decisions for package design, performance maps based on the different design parameters are desired for mid-frequencies. This paper presents a framework to retrieve the response surface, from a numerical design space of finite-element frequency sweeps. This response surface describes the performance of a sound package against the different design variables.

The combination of lightweight design and performant Noise, Vibrations Harshness (NVH) solutions has gained a lot of importance over the past decades. Lightweight design complies with the ever more stringent environmental requirements, however conflicts with NVH performance, as low noise and vibration levels often require heavy and bulky systems, especially at low frequencies. To face this challenge, locally resonant metamaterials come to the fore as low mass, compact volume NVH solutions, beating the mass law in some tunable frequency zones, referred to as stopbands. Metamaterials are artificial materials made from assemblies of unit cells of non-homogeneous material composition and/or topology. The local interaction between unit cells leads to superior performance in terms of noise and vibration reduction with respect to the conventional NVH treatments. Previously the authors showed how wave propagation along one-dimensional structures can be reduced by metamaterial additions.

In the context of the reduction of traffic-related noise the research reported in this paper provides tools that could be used to develop low noise tyres. Two measurement techniques have been analyzed for exterior noise radiation characterization of a loaded rotating slick tyre on a rough road surface. On one hand sound pressure measurements at low spatial resolution with strategically placed microphones on a half-hemisphere around the tyre/road contact point have been performed. This technique provides a robust solution to compute the (overall) sound power level. On the other hand sound intensity measurements at high spatial resolution by means of a scanning intensity probe have been performed. This technique allows a more detailed spatial visualization of the noise radiation and helps in getting more insight and better understanding of the acoustical phenomena.

This paper presents a newly developed hybrid simulation technique for uncoupled acoustic analysis of interior cavities. This method applies a Wave Based model for a large, geometrically simple portion of the acoustic cavity. The superficial details of the problem domain are modeled using a modally reduced finite element model. The resulting hybrid model benefits from the computational efficiency of the Wave Based Method, while retaining the Finite Element Method's ability to model the actual geometry of the problem in great detail. Application of this approach to the analysis of a moderately simplified acoustic car cavity shows the improved computational efficiency as compared to classical finite element procedures and illustrates the potential of the hybrid method as a powerful tool for the analysis of three-dimensional interior acoustic systems.

The NVH optimization of new vehicle models can in principle only be carried out in a relatively late stage of the development process, when the geometrical data (CAD) are available and can be used to generate detailed Finite Element (FE) models of the car body. Unfortunately, in this stage of the development process most of the geometrical data are already fixed and countermeasures are limited and expensive. In order to be able to evaluate design concepts in an earlier conceptual stage of the development process existing models of similar predecessor vehicles must be used leading to techniques such as “mesh-morphing” or “concept modelling” (see for instance [1, 2]). Here, a different approach is investigated based on a substructuring technique.