Search Results

Throughout the first decade of the twenty first century, large improvements in occupant safety have been made in NASCAR®'s (National Association for Stock Car Auto Racing, Inc) race series. Enhancements to the occupant restraint system include the development and implementation of head and neck restraints, minimum performance requirements for belts and seats and the introduction of energy absorbing foam are a few highlights, among others. This paper discusses nineteen sled tests used to analyze hypothesized improvements to restraint system mounting geometry. The testing matrix included three sled acceleration profiles, three impact orientations, two Anthropomorphic Test Device (ATD) sizes as well as the restraint system design variables.

This study examines the static pressure distribution under both width belts in the shoulder and the pelvis of 15 volunteer subjects. The subjects applied the belt loads to themselves through a lever and pulley system. The configuration of the belts simulated the typical arrangement of a six-point belted upright-seated racing driver. The pressure distribution between the belt and the volunteer's body was determined and recorded with Tek-Scan pressure sensing grids. The paper presents the results of the measurements by comparing the actual area of significant loading beneath the two widths and materials of both lap and shoulder belts. In, general, there no significant increase in loaded area for the wider belts.

This paper describes the results of an ongoing project in the GM Motorsports Safety Technology Research Program to investigate Indianapolis-type (Indy car) race car crashes using an on-board impact recorder as the primary data collection tool. The paper discusses the development of specifications for the impact-recording device, the selection of the specific recorder and its implementation on a routine basis in Indy car racing. The results from incidents that produced significant data (crashes with peak decelerations above 20 G) during the racing seasons from 1993 through the first half of 1998 are summarized. The focus on Indy car crashes has proven to provide an almost laboratory-like setting due to the similarity of the cars and to the relative simplicity of the crashes (predominantly planar crashes involving single car impacts against well-defined impact surfaces).

Recent developments in seat design for racecar drivers have proven to be very effective in minimizing injuries in side impacts. The features of the seats that present significant improvements over previous concepts are based on biomechanical principles that were learned from crash recorder based investigations of Indy car crashes. Insights gained from these studies led to an understanding of critical factors that provide effective support and protection of the driver in a high-severity side impact crash. Transferring these concepts from single seat chassis cars to stock car and sports car seats has led to significant improvements in driver side impact protection. The paper will describe these principles, present sled test performance data showing the benefits of proper seat design and will give examples of current commercially available seat designs for stock car and sports car racing.

This paper discusses the development of adequate criteria and evaluation methods for seat belt restraint design. These criteria should include the effect of seat belts in abdominal injury as well as head injury. It is concluded that belt load limiters and energy-absorbing devices should limit head-to-vehicle contact, ensure that the lap belt maintains proper contact with the bony pelvic girdle, and limit the belt loads. Studies are made of pulse shape and belt fabrics. Currently available mathematical models are used for the studies included in the paper.

This paper presents the results of a series of over 30 impact sled simulations of racing car frontal crashes conducted as part of the GM Motorsports Safety Technology Research Program. A Hyge™ impact sled fitted with a simulated racing car seat and restraint system was used to simulate realistic crash loading with a mid-size male Hybrid III dummy. The results of tests, in the form of measured loads, displacements, and accelerations, are presented and comparisons made with respect to the levels of these parameters seen in typical passenger car crash testing and to current injury threshold values.

The close-fitting cockpit of the modern Indy car single seat race car has the potential to provide a high level of head and neck impact protection in rear and side impacts. Crash investigation has shown that a wide variety of materials have been used as the padding for these cockpits and, as a result, produced varying outcomes in crashes. Additionally, these pads have not always been positioned for optimal performance. The purpose of this study was to investigate the head impact performance of a variety of energy-absorbing padding materials under impact conditions typical of Indy car rear impacts and to identify superior materials and methods of improving their performance as race car head pads. An extensive series of tests with the helmeted Hybrid III test dummy head and neck on an impact mini-sled was conducted to explore head padding concepts.

Biomechanical analysis of Indy car crashes using on-board impact recorders (Melvin et al. 1998, Melvin et al. 2001) indicates that Indy car driver protection in high-energy crashes can be achieved in frontal, side, and rear crashes with severities in the range of 100 to 135 G peak deceleration and velocity changes in the range of 50 to 70 mph. These crashes were predominantly single-car impacts with the rigid concrete walls of oval tracks. This impressive level of protection was found to be due to the unique combination of a very supportive and tight-fitting cockpit-seating package, a six-point belt restraint system, and effective head padding with an extremely strong chassis that defines the seat and cockpit of a modern Indy car. In 2000 and 2001, a series of fatal crashes in stock car racing created great concern for improving the crash protection for drivers in those racecars.

Over the last decade large safety improvements have been made in crash protection for stock car racing drivers. It has been well established that in side and rear impacts the driver seat provides the primary source for occupant retention and restraint. With the implementation of NASCAR®'s (National Association for Stock Car Auto Racing, Inc) newest generation of stock car, the Car of Tomorrow (COT), into the racing schedule, the opportunity to develop and implement a universal stock car driver seat performance specification was accomplished. This paper describes the development of the Seat Performance Specification including the goals of the specification, the methodology used to develop it, a census of the existing driver seat population used in on-track competition, review of developmental dynamic specification sled tests and quasi-static tests as well as summation of the Seat Performance Specification requirements.