Refine Your Search

Date

Date

Topic

Topic

Finishing Corrosion On-board energy sources SAE IC Powertrain Steering Committee Heat resistant materials

Search Results

Viewing 1 to 20 of 29
12Next >Last >>
Sort by published
Standard

EMISSION TEST DRIVING SCHEDULES
1991-06-01
HISTORICAL
J1506_199106
This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this document will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This document includes: a. Descriptions of driving schedules; and b. Second-by second definition of speed versus time sequences.
Standard

EMISSION TEST DRIVING SCHEDULES
1988-06-01
HISTORICAL
J1506_198806
This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this information report will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This information report includes: 1 - Descriptions of driving schedules. 2 - Second-by second definition of speed versus time sequences.
Standard

REPORTING ON EMISSION TESTING FOR IN-USE LIGHT-DUTY TRUCKS AND PASSENGER VEHICLES
2000-10-01
HISTORICAL
J1712_200010
This SAE Recommended Practice applies to the reporting of laboratory and test site data from the gaseous and evaporative emission tests of in-use light-duty trucks and passenger vehicles. This document describes the reporting of procedures, fuel specifications, and vehicle information necessary to compare the results of in-use tests. Any variations in vehicles, instrumentation, test equipment, or test program purpose should be adequately described.
Standard

THRUST WASHERS—DESIGN AND APPLICATION
1995-02-01
HISTORICAL
J924_199502
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

Thrust Washers – Design and Application
2011-06-13
CURRENT
J924_201106
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases, the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

THRUST WASHERS—DESIGN AND APPLICATION
1981-01-01
HISTORICAL
J924_198101
This SAE Standard presents the basic size and tolerance information for the design and manufacture of thrust washers. In most cases the standard employs nominal figures in both metric and inch-pound units and, therefore, does not necessarily provide exact equivalents.
Standard

Measurement of Fuel Evaporative Emissions from Gasoline Powered Passenger Carsand Light Trucks Using the Enclosure Technique
2000-12-07
CURRENT
J171_200012
This SAE Recommended Practice describes a procedure for measuring evaporative emissions from fuel systems of passenger cars and light trucks. Emissions are measured during a sequence of laboratory tests that simulate typical vehicle usage in a metropolitan area during summer months: a. A 1 h soak representing one diurnal cycle in which temperature of fuel in the vehicle's tank is raised from 15.6 to 28.9 °C (60 to 84 °F) b. A 17.9 km (11.1 mile) drive on a chassis dynamometer c. A 1 h hot soak immediately following the 17.9 km (11.1 mile) drive The method described in this document, commonly known as the SHED (Sealed Housing for Evaporative Determination) technique, employs an enclosure in which the vehicle is placed during the diurnal and hot soak phases of the test.
Standard

Application Guide to Radial Lip Seals
2002-10-25
CURRENT
J946_200210
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
Standard

Multiposition Small Engine Exhaust System Fire Ignition Suppression
2020-10-06
CURRENT
J335_202010
This SAE Recommended Practice establishes equipment and test procedures for determining the performance of spark arrester exhaust systems of multiposition small engines (<19 kW) used in portable applications, including hand-held, hand-guided, and backpack mounted devices. It is not applicable to spark arresters used in vehicles or stationary equipment.
Standard

SEALS—TERMINOLOGY OF RADIAL LIP
1997-05-01
HISTORICAL
J111_199705
The purpose of this SAE Recommended Practice is to provide a glossary of radial seal terms and nomenclature which are normally encountered in the design, manufacture, installation, testing, inspection, and failure mode analysis of radial seals. The information will aid in the understanding and communication among those people associated with radial seals.
Standard

Diesel Smoke Measurement Procedure
1995-03-01
HISTORICAL
J35_199503
This SAE Recommended Practice applies to the dynamometer test procedure which can be used to assess the smoke emission characteristics of vehicular diesel engines. In particular, this procedure describes the smoke test cycle, equipment and instrumentation, instrument checks, chart reading, and calculation for evaluation of an engine's transient smoke emission characteristic. In addition, this procedure offers guidelines to be used in establishing correlation between full flow in-line and end-of-line opacimeters. Since the type of test described here is transient in nature, a fast responding full flow opacimeter is required for the smoke measurements. Slow responding or sampling, or both, type instruments must not be used since they typically have excessive and variable response delays and do not provide an accurate measurement of an engine's transient smoke characteristics.
12Next >Last >>
X