Standard
SURFACE ROLLING AND OTHER METHODS FOR MECHANICAL PRESTRESSING OF METALS
1981-08-01
HISTORICAL
J811_198108
Search Results
Standard
Surface Rolling and Other Methods for Mechanical Prestressing of Metals
2017-06-07
CURRENT
J811_201706
Standard
SAE Manual on Shot Peening
1967-11-01
HISTORICAL
J808A_196711
This report is intended to provide users and producers of metallic shot and grit1 with general information on methods of mechanically testing metal abrasives in the laboratory.
Standard
Definition for Particle Size
2011-06-01
CURRENT
J391_201106
"Effective particle or domain size" is a phrase used in X-ray diffraction literature to describe the size of the coherent regions within a material which are diffracting. Coherency in this sense means diffracting as a unit. Small particle size causes X-ray line broadening and as such can be measured. It has been shown related to substructure as observed in transmission electron microscopy. Particle size is affected by hardening, cold working, and fatigue; conversely, there is increasing evidence that particle size, per se, affects both static and dynamic strength.
Standard
DEFINITIONS FOR MACROSTRAIN AND MICROSTRAIN
1985-08-01
HISTORICAL
J932_198508
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
Standard
Definitions for Macrostrain and Microstrain
2011-08-04
CURRENT
J932_201108
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
Standard
Medical Device Shot Peening
2014-05-07
CURRENT
J3020_201405
This SAE Standard and its supplementary detail specifications cover the engineering requirements for the controlled shot peening of a medical device where shot peening is required for enhancement of a material's mechanical properties through the intentional creation of compressive residual stress.
Standard
Shot Peening
2015-06-30
CURRENT
J2441_201506
This SAE Standard covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot.
Standard
Shot Peening
2000-08-01
HISTORICAL
J2441_200008
This SAE Standard covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot.
Standard
CAST STEEL SHOT
1990-03-01
HISTORICAL
J827_199003
This SAE Recommended Practice describes chemical analysis, hardness, microstructure and physical characteristic requirements for cast steel shot to be used for shot peening or blast cleaning operations.
Standard
CAST STEEL SHOT
1962-06-01
HISTORICAL
J827_196206
Standard
CAST STEEL SHOT
1969-01-01
HISTORICAL
J827_196901
Standard
CAST STEEL GRIT
1993-03-01
HISTORICAL
J1993_199303
This SAE Recommended Practice describes the chemical composition and the physical requirements for high carbon cast steel grit.
Standard
CUT WIRE SHOT
1987-05-01
HISTORICAL
J441_198705
Standard
CUT WIRE SHOT
1993-06-01
HISTORICAL
J441_199306
This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.
Standard
Metallic Shot and Grit Mechanical Testing
2022-05-04
CURRENT
J445_202205
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard
Metallic Shot and Grit Mechanical Testing
2005-07-25
HISTORICAL
J445_200507
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard
METALLIC SHOT AND GRIT MECHANICAL TESTING
1996-04-01
HISTORICAL
J445_199604
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard
Metallic Shot and Grit Mechanical Testing
2013-08-21
HISTORICAL
J445_201308
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
Standard
METALLIC SHOT AND GRIT MECHANICAL TESTING
1984-08-01
HISTORICAL
J445_198408
This report is intended to provide users and producers of metallic shot and grit1 with general information on methods of mechanically testing metal shot in the laboratory.
