This SAE Recommended Practice establishes uniform laboratory techniques for the measurement and determination of the susceptibility of electromagnetic interference of electrical, electronic and electromechanical ground vehicle components.
This SAE Recommended Practice establishes uniform laboratory measurement techniques for the determination of the susceptibility to undesired electromagnetic sources of electrical, electronic, and electromechanical ground-vehicle components. It is intended as a guide toward standard practice, but may be subject to frequent change to keep pace with experience and technical advances, and this should be kept in mind when considering its use.
This SAE Recommended Practice establishes uniform laboratory measurement techniques for the determination of the susceptibility to undesired electromagnetic sources of electrical, electronic, and electromechanical ground-vehicle components. It is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances, and this should be kept in mind when considering its use.
This information report gives typical requirements for an anechoic chamber in which the system susceptibility of an operating motor vehicle to electromagnetic fields can be determined in the frequency range of 20 MHz to 18 GHz. Because of the large cone sizes required for 20 MHz cut-off, several anechoic facilities have been designed with lower cut-off frequencies of 200 MHz or greater. Testing below cut-off is then accomplished using customized antennas at reduced accuracy. Users should carefully review their testing requirements before undertaking the construction of a test facility the magnitude of an anechoic chamber. Other test approaches include, but are not limited to, open field testing per SAE J1338 and mode stirred reverberation chambers.
This SAE Information Report defines the test methods and specifications for the electrostatic discharge sensitivity of passenger cars, multipurpose passenger vehicles, trucks and buses.
This document establishes a method of determining the relative level of susceptibility of electronic modules and the improvement or degradation which results from design changes to those modules. Further work needs to be done to correlate this module test to whole vehicle coupling in an electromagnetic field.
This information report gives the procedures for use and operation of a large transverse electromagnetic (TEM) mode cell for the determination of electromagnetic (EM) radiated susceptibility of equipment, subsystems and systems (whose dimensions are less than 3 m × 6 m × 18 m) in the frequency range 10 kHz–20 MHz. Several large TEM cells have been designed and constructed by various organizations for EMP and high power CW testing. Two cell designs and associated instrumentation are included for example purposes in this report. Other cell configurations have also been constructed. Users should consult the literature before undertaking a project of this magnitude for other cell and instrumentation designs.
This information report gives the procedures for use and operation of a large transverse electromagnetic (TEM) mode cell for the determination of electromagnetic (EM) radiated susceptibility of equipment, subystems and systems (whose dimensions are less than 3 m x 6 m x 18 m) in the frequency range 10 kHz - 20 MHz. Several large TEM cells have been designed and constructed by various organizations for EMP and high power CW testing. Two cell designs and associated instrumentation are included for example purposes in this report. Other cell configurations have also been constructed. Users should consult the literature before undertaking a project of this magnitude for other cell and instrumentation designs.
This information report gives the procedures for use and operation of a large transverse electromagnetic (TEM) mode cell for the determination of electromagnetic (EM) radiated susceptibility of equipment, subsystems and systems (whose dimensions are less than 3 m × 6 m × 18 m) in the frequency range 10 kHz - 20 MHz. Several large TEM cells have been designed and constructed by various organizations for EMP and high power CW testing. Two cell designs and associated instrumentation are included for example purposes in this report. Other cell configurations have also been constructed. Users should consult the literature before undertaking a project of this magnitude for other cell and instrumentation designs.
This standard covers the measurement of radiation from all motor vehicle sources (including auxiliary engines) with the exception of short duty cycle equipment, such as starting motors, window regulators, turn signals, etc., over a frequency range of 20-1000 MHz.
This standard covers the measurement of electromagnetic radiation from a motor vehicle or other internal-combustion-powered device (excluding aircraft) over a frequency range of 20-1000 MHz. In the case of motor vehicle sources, auxiliary engines mounted on the vehicle are included and short-duty cycle equipment (such as starting motors, window regulators, turn signals, flashing warning lights, etc.) are excluded.
This standard covers the measurement of radiation from all motor vehicle sources (including auxiliary engines) with the exception of short duty cycle equipment, such as starting motors, window regulators, turn signals, etc., over a frequency range of 20-1000 MHz.
This standard covers the measurement of impulsive electromagnetic radiation over the frequency range of 20 to 1(100 MHz from a motor vehicle or other device powered by an internal combustion engine. Operation of all engines (main and auxiliary) on a vehicle or other device is included. All equipment normally operating when the engine is running is also included, except operator-controlled equipment, which is excluded. The recommended limit applies only to complete vehicles or devices in their final manufactured form.
This SAE Standard contains limits1 and procedures for the measurement of radio disturbances in the frequency range of 150 kHz to 1000 MHz. The standard applies to any electronic/electrical component intended for use in vehicles and large devices. Refer to International Telecommunications Union (ITU) Publications for details of frequency allocations. The limits are intended to provide protection for receivers installed in a vehicle from disturbances produced by components/modules in the same vehicle.2 The receiver types to be protected are: sound and television receivers3, land mobile radio, radio telephone, amateur and citizens' radio. For the purpose of this document, a vehicle is a machine which is self-propelled. Vehicles include (but are not limited to) passenger cars, trucks, agricultural tractors, and snowmobiles. The limits in this document are recommended and subject to modification as agreed between the vehicle manufacturer and the component supplier.
This part of SAE J551 specifies on-board transmitter simulation test methods and procedures for testing passenger cars and commercial vehicles. The electromagnetic disturbances considered in this part of SAE J551 are limited to continuous narrow band electromagnetic fields. SAE J551/1 specifies general, definitions, practical use, and basic principles of the test procedure.
This SAE Standard contains test limits and procedures for the measurement of radio disturbances in the frequency range of 150 kHz to 1000 MHz. The document applies to any electronic/electrical component intended for use in vehicles. Refer to International Telecommunications Union (ITU) Publications for details of frequency allocations. The test limits are intended to provide protection for receivers installed in a vehicle from disturbances produced by components/ modules in the same vehicle. The receiver types to be protected are: broadcast radio and TV, land-mobile radio, radio telephone, amateur and citizens' radio. The limits in this document are recommended and subject to modification as agreed between the vehicle manufacturer and the component supplier. This document shall also be applied by manufacturers and suppliers of components and equipment which are to be added and connected to the vehicle harness or to an on-board power connector after delivery of the vehicle.
The limits in this SAE Standard are designed to provide protection for receivers of all types of radio transmissions when used in buildings. As a result, receivers of radio transmissions used out-of-doors may not be protected by the limits specified. This publication applies to the emission of electromagnetic energy which may cause interference to radio reception and which is emitted from: a Vehicles propelled by an internal combustion engine, electrical means or both (see SAE J551/1 for definition) b Motorboats propelled by an internal combustion engine, electrical means or both NOTE—For the purposes of this publication, motorboats are considered to be a subset of vehicles unless specifically mentioned to the contrary. c Devices equipped with spark-ignited internal combustion engines (see SAE J551/1 for definition) This publication does not apply to aircraft, traction systems (railway, tramway, and trolley bus), or to incomplete vehicles.
The limits in this SAE Standard are designed to provide protection for receivers of all types of radio transmissions when used in buildings. As a result, receivers of radio transmissions used out-of-doors may not be protected by the limits specified. This publication applies to the emission of electromagnetic energy which may cause interference to radio reception and which is emitted from: a. vehicles propelled by an internal combustion engine, electrical means or both (see SAE J551/1 for definition); b. motorboats propelled by an internal combustion engine, electrical means or both; and c. devices equipped with spark-ignited internal combustion engines (see SAE J551/1 for definition). This publication does not apply to aircraft, traction systems (railway, tramway, and trolley bus), or incomplete vehicles.
This part of SAE J551 specifies off-vehicle radiation source test methods and procedures for testing passenger cars and commercial vehicles. Two methods for calibrating electromagnetic fields are defined in the document: a substitution method and a closed-loop method. The substitution method is the method most commonly used. SAE J551-1 specifies general, definitions, practical use, and basic principles of the test procedure.