Search Results

This talk will present an overview of the newly published DO-326/ED-202 "Airworthiness Security Process Specification". Presenter Daniel P. Johnson, Honeywell

Commercial transport aircraft have adopted TCP/IP based onboard networking technology to integrate information interchange. This change along with the addition of a TCP/IP based air-ground data link will permit the aircraft network to establish links with ground networks and be integrated into the airline enterprise network. There are many challenging considerations when connecting a remote network to an enterprise network. These challenges are multiplied when that remote network is constantly in motion, both physically and in terms of its link to the ground network. An important consideration in any enterprise network is the element of security. AEEC has published ARINC Report 811: Commercial Aircraft Information Security Concepts of Operation and Process Framework [1] as a guide for the airlines as they consider how to deal with this new challenge.

The implementations of the Tier 2 and LEVII emission levels require fast catalyst light-off and fast closed loop control through high-speed engine management. The paper describes the development of innovative catalyst designs. During the development thermal and mechanical boundary conditions were collected and component tests conducted on test rigs to identify the emission and durability performance. The products were evaluated on a Super Imposed Test Setup (SIT) where thermal and mechanical loads are applied to the test piece simultanously and results are compared to accelerated vehicle power train endurance runs. The newly developed light-off catalyst with Perforated Foil Technology (PE) showed superior emission light-off characteristic and robustness.

This work deals with the modeling and analysis of both AC and DC bus voltage control in aerospace applications. The results of the analysis are presented along with system models, including a voltage-controlled current source (vccs) used as a DC Bus controller, a d,q-controlled, IGBT-based, SVPWM-switched, ac-to-dc active converter/rectifier (AR) used as a DC Bus controller, a 3-phase ac generator voltage regulator (VR) used as an AC Bus controller, a 3-phase uncontrolled ac generator followed by an SCR-controlled ac-to-dc converter, used as a DC Bus controller (single-controlled bus), and a 3-phase dynamically-controlled ac generator followed by an SCR-controlled ac-to-dc converter, used to provide both AC and DC Bus control (dual-controlled bus).

This paper discusses the problem of designing electric machines (EM) for advanced electric generators (AEG) used in aerospace more electric architecture (MEA) that would be applicable to aircraft, spacecraft, and military ground vehicles. The AEG's are analyzed using aspects of Six Sigma theory that relate to critical-to-quality (CTQ) subjects. Using this approach, weight, volume, reliability, efficiency, and cost (CTQs) are addressed to develop a balance among them, resulting in an optimized power generation system. The influence of the machine power conditioners and system considerations are also discussed. As a part of the machine evaluation process, speeds, bearings, complexities, rotor mechanical and thermal limitations, torque pulsations, currents, and power densities are also considered. A methodology for electric machine selection is demonstrated. Examples of high-speed, high-performance machine applications are shown.

A detailed study was conducted on nitrification using a bench top bioprocessor system proposed for water recycling of a urine-soap wastewater expected to be generated by crewmembers on International Space Station (ISS) or similar long-term space missions. The bioprocessor system consisted of two packed bed biofilm reactors; one anoxic reactor used for denitrification and one aerobic reactor used for nitrification. lnfluent wastewater was a mixture of dilute NASA whole body soap (2,300 mg/L) and urea (500 mg/L as organic nitrogen). During two months of steady-state operation, average chemical oxygen demand (COD) removal was greater than 95%, and average total nitrogen removal was 70%. We observed that high levels of nitrite consistently accumulated in the aerobic (nitrifying) reactor effluent, indicating incomplete nitrification as the typical end product of the reaction would be nitrate.

The bleed air contamination monitor was developed at Honeywell to ensure that our products provide the highest quality bleed air to aircraft environmental control systems. The bleed air contamination monitor is currently for ground based applications only. It is being developed into an on board system for future applications. Current Aircraft Cabin Air Quality measurement techniques are very labor intensive and require days or even weeks of laboratory analysis to provide results. This is unacceptable from a manufacturing and service perspective. Development of a real time analyzer began in the early 1990s and has progressed to a point where a product is ready for introduction that not only provides real time information regarding engine air contamination, but is also easy for operators to use with a minimum amount of training.

Current Environmental Control and Life Support Systems (ECLSS), particularly on large systems, have a tendency to include several heterogeneous processing elements. This approach is also the default in the commercial aircraft industry. However, Honeywell has been extremely successful in the past decade in using an integrated modular approach to command and data handling for aircraft avionics. This approach, dubbed “Fifth Generation Avionics” by the Air Force's Wright Laboratory, has resulted in significant reductions in the size, weight, power, and acquisition costs of the data handling subsystem. Logistics, modification, and upgrade costs also decreased considerably. While commonality is maximized in the integrated modular architecture, each application continues to be independent with internal designs completely under the control of the application developer.

The operating environment of aircraft causes accumulation and build-up of contamination on both the narrowest passages of the ECS (Environmental Control System) i.e: the heat exchangers. Accumulated contamination may lead to reduction of performance over time, and in some case to failures causing AOG (Aircraft on Ground), customer dissatisfaction and elevated repair costs. Airframers/airlines eschew fixed maintenance cleaning intervals because of the high cost of removing and cleaning these devices preferring instead to rely on on-condition maintenance. In addition, on-wing cleaning is t impractical because of installation constrains. Hence, it is desirable to have a contamination monitoring that could alert the maintenance crew in advance to prepare and minimize disruption when contamination levels exceed acceptable thresholds. Two methods are proposed to achieve this task, The effectiveness of these methods are demonstrated using analytical and computational tools.

Increased nickel concentrations in the IATCS coolant prompted a study of the corrosion rates of nickel-brazed heat exchangers in the system. The testing has shown that corrosion is occurring in a silicon-rich intermetallic phase in the braze filler of coldplates and heat exchangers as the result of a decrease in the coolant pH brought about by cabin carbon dioxide permeation through polymeric flexhoses. Similar corrosion is occurring in the EMU de-ionized water loop. Certain heat exchangers and coldplates have more silicon-rich phase because of their manufacturing method, and those units produce more nickel corrosion product. Silver biocide additions did not induce pitting corrosion at silver precipitate sites.

Two campaigns measuring on-road emissions of 23 VN-trucks on a randomly chosen driving cycle, consisting of 10 miles two-lane and 8 miles four-lane road were performed. The first, during October 2004, showed tailpipe NOx emissions on fleet average of 1.06 g/bhp-hr including the time the exhaust gas temperature was below 200°C. The second, during June 2005, showed tailpipe NOx emissions on fleet average of 1.13 g/bhp-hr including the time the exhaust gas temperature was below 200°C. Complementary measurements in a SET-cycle (13 point OICA-cycle) on a chassis dynamometer showed a tailpipe emission of 0.008 g PM per bhp-hr. Moreover, cost analysis show that the diesel fuel consumption remains unchanged whether the truck running on ULSD is equipped with a Combined Exhaust gas AfterTreatment System (CEATS) installed or not.

Six 2001 International Class 6 trucks participated in a project to determine the impact of gas-to-liquid (GTL) fuel and catalyzed diesel particle filters (DPFs) on emissions and operations from December 2003 through August 2004. The vehicles operated in Southern California and were nominally identical. Three vehicles operated “as-is” on California Air Resources Board (CARB) specification diesel fuel and no emission control devices. Three vehicles were retrofit with Johnson Matthey CCRT® (Catalyzed Continuously Regenerating Technology) filters and fueled with Shell GTL Fuel. Two rounds of emissions tests were conducted on a chassis dynamometer over the City Suburban Heavy Vehicle Route (CSHVR) and the New York City Bus (NYCB) cycle. The CARB-fueled vehicles served as the baseline, while the GTL-fueled vehicles were tested with and without the CCRT filters. Results from the first round of testing have been reported previously (see 2004-01-2959).

A fleet of six 2001 International Class 6 trucks operating in southern California was selected for an operability and emissions study using gas-to-liquid (GTL) fuel and catalyzed diesel particle filters (CDPF). Three vehicles were fueled with CARB specification diesel fuel and no emission control devices (current technology), and three vehicles were fueled with GTL fuel and retrofit with Johnson Matthey's CCRT™ diesel particulate filter. No engine modifications were made. Bench scale fuel-engine compatibility testing showed the GTL fuel had cold flow properties suitable for year-round use in southern California and was additized to meet current lubricity standards. Bench scale elastomer compatibility testing returned results similar to those of CARB specification diesel fuel. The GTL fuel met or exceeded ASTM D975 fuel properties. Researchers used a chassis dynamometer to test emissions over the City Suburban Heavy Vehicle Route (CSHVR) and New York City Bus (NYCB) cycles.

Aircraft accidents caused by explosion of the vapor within the fuel tanks have been the subject of many recent articles. Methods of either suppressing the combustion or preventing the ignition have been considered. Indeed, solutions such as liquid nitrogen, halon, and reticulated foam have been installed on production aircraft. However, these have proved to be expensive to operate or are being phased out. By working together, the authors have developed the capability to provide fully integrated On-Board Inert Gas Generating Systems (OBIGGS) based on novel hollow fiber membrane technology. An overview of the advantages of such an approach is presented together with an outline of the system design method. The importance of considering the effect of differing flight profiles, and the inter-reactions of the OBIGGS, with the Fuel System, Engine Bleed Air Management, and Environmental Control Systems in the design process are emphasized.

In a consortium of European industrial partners and research institutes, a combination of industrial development and scientific research was organised. The objective was to improve the catalytic NOx conversion for lean burn cars and heavy-duty trucks, taking into account boundary conditions for the fuel consumption. The project lasted for three years. During this period parallel research was conducted in research areas ranging from basic research based on a theoretical approach to full scale emission system development. NOx storage catalysts became a central part of the project. Catalysts were evaluated with respect to resistance towards sulphur poisoning. It was concluded that very low sulphur fuel is a necessity for efficient use of NOx trap technology. Additionally, attempts were made to develop methods for reactivating poisoned catalysts. Methods for short distance mixing were developed for the addition of reducing agent.

In the search for clean and efficient power, PEM fuel cells have been identified as the technology that can meet our future needs for transport applications. Hydrogen-powered PEM fuel cell vehicles are perceived to give the ultimate advantage, but the complications involved with hydrogen storage and refuelling, as well as the lack of infrastructure call for a different solution. In the near term, this is almost certain to be the on-board generation of hydrogen from a readily available fuel. At Johnson Matthey, a novel modular reformer (HotSpot™) has been developed for methanol, and has been demonstrated to have many of the qualities that are required for automotive applications. Auxiliary technologies for CO removal (Demonox) and aftertreatment have also been developed, and integrated with the reformer to form 20 kWe processor, which is currently undergoing brass-board testing.

Previous studies have shown that regenerating particulate filters are very effective at reducing particulate matter emissions from diesel engines. Some particulate filters are passive devices that can be installed in place of the muffler on both new and older model diesel engines. These passive devices could potentially be used to retrofit large numbers of trucks and buses already in service, to substantially reduce particulate matter emissions. Catalyst-type particulate filters must be used with diesel fuels having low sulfur content to avoid poisoning the catalyst. A project has been launched to evaluate a truck fleet retrofitted with two types of passive particulate filter systems and operating on diesel fuel having ultra-low sulfur content. The objective of this project is to evaluate new particulate filter and fuel technology in service, using a fleet of twenty Class 8 grocery store trucks. This paper summarizes the truck fleet start-up experience.

A multi-year technology validation program was completed in 2001 to evaluate ultra-low sulfur diesel fuels and passive diesel particle filters (DPF) in several different diesel fleets operating in Southern California. The fuels used throughout the validation program were diesel fuels with less than 15-ppm sulfur content. Trucks and buses were retrofitted with two types of passive DPFs. Two rounds of emissions testing were performed to determine if there was any degradation in the emissions reduction. The results demonstrated robust emissions performance for each of the DPF technologies over a one-year period. Detailed descriptions of the overall program and results have been described in previous SAE publications [2, 3, 4, 5]. In 2002, a third round of emission testing was performed by NREL on a small subset of vehicles in the Ralphs Grocery Truck fleet that demonstrated continued robust emissions performance after two years of operation and over 220,000 miles.