Search Results

A multi-chamber silencer is designed by a computational approach to suppress the turbocharger whoosh noise downstream of a compressor in an engine intake system. Due to the significant levels and the broadband nature of the source spanning over 1.5 – 3.5 kHz, three Helmholtz resonators are implemented in series. Each resonator consists of a chamber and a number of slots, which can be modeled as a cavity and neck, respectively. Their target resonance frequencies are tuned using Boundary Element Method to achieve an effective noise reduction over the entire frequency range of interest. The predicted transmission loss of the silencer is then compared with the experimental results from a prototype in an impedance tube setup. In view of the presence of rapid grazing flow, these silencers may be susceptible to whistle-noise generation. Hence, the prototype is also examined on a flow bench at varying flow rates to assess such flow-acoustic coupling.

The acoustic and performance characteristics of an automotive centrifugal compressor are studied on a steady-flow turbocharger test bench, with the goal of advancing the current understanding of compression system instabilities at the low-flow range. Two different ducting configurations were utilized downstream of the compressor, one with a well-defined plenum (large volume) and the other with minimized (small) volume of compressed air. The present study measured time-resolved oscillations of in-duct and external pressure, along with rotational speed. An orifice flow meter was incorporated to obtain time-averaged mass flow rate. In addition, fast-response thermocouples captured temperature fluctuations in the compressor inlet and exit ducts along with a location near the inducer tips.

There are many methods developed over the past decade to solve the problem of energy management control for hybrid electric vehicles. A novel method is introduced in this paper to address the same problem which reduces the problem to a set of physical equations and maps. In simple terms, this method directly calculates the actual cost or savings in fuel energy from the generation or usage of electric energy. It also calculates the local optimum electric power that yields higher electric fuel savings (EFS) or lower electric fuel cost (EFC) in the fuel energy that is spent for driving the vehicle (which in general does not take the system to the lowest engine Brake Specific Fuel Consumption (BSFC)). Based on this approach, a control algorithm is developed which attempts to approach the global optimum over a drive cycle.

Cooled LPL EGR is a proven means of improving the efficiency of a Gasoline Turbocharged Direct-Injection engine. One of the most significant hurdles to overcome in implementing a LPL EGR system is dealing with condensation of water near the entrance of the turbocharger's compressor wheel. A gasoline engine, and to a greater extent a spark ignition engine running on Natural Gas, will encounter enough water condensation at some steady-state conditions to damage the compressor wheel due to the high-speed collision between the compressor blades and the water droplets. As an alternative to not utilizing beneficial EGR at the condensing conditions, the team at BorgWarner have developed a LPL EGR mixer that is effective at condensing and collecting the water droplets and routing the water around the compressor wheel. The new Condensing EGR mixer was developed from the known concept of utilizing a mild venturi section to enhance EGR delivery and mixing.

Roll forming assemblies are generally neat and robust, but there are structural integrity risks involved too if the forming procedures and design features do not complement each other. Specifically, in solenoid valves, an imprecised roller crimping (or forming) adversely affect the desired magnetic performance of the valves. Furthermore, in-depth evaluations of the formed shape using hardware and lab testing are extremely challenging cost wise and time consuming as well. However, utilizing simulation technique such as finite element analysis (FEA) to understand the in-sights of roller formed assemblies of a solenoid valve (or other products) could be an effective way to minimize overall cost and time involved in the product development. Therefore, a three-dimensional non-linear FEA model of roller crimping simulation was established in ANSYS Workbench Mechanical, and the predicted results were correlated with real hardware data to prove the technique & process adopted.

This paper gives a thorough review of the HC/CO emissions challenge and discusses the effects of different diesel oxidation catalyst designs in a pre turbine and post turbine position on steady state and transient turbo charger performance as well as on HC and CO tailpipe emissions, fuel economy and performance of modern Diesel engines. Results from engine dynamometer testing are presented. Both classical diffusive and advanced premixed Diesel combustion modes are investigated to understand the various effects of possible future engine calibration strategies.

Trying to improve the modern diesel engine's NOx/soot tradeoff without giving up fuel economy continues to be a core target for the engine development community. One of the options not yet fully investigated for the diesel is applying variable valve events to the engine breathing process. Already used in some heavy-duty applications, late intake valve closing has long been regarded as a possible strategy for small diesel engines. Single-cylinder tests applying fully variable valve events have demonstrated potential but also raised doubts about VVA benefits on automotive size diesel engines. Full engine testing using realistic valve train technology is seen as key to judging its true performance because it covers not only combustion benefits but also influences like engine pumping on emissions and CO₂. Different to past publications, this paper focuses on testing a production feasible variable valve train technology on a fully instrumented modern Common Rail diesel engine.

In our introductory paper on the VEMB system (SAE 2010-01-1222) we discussed the concept of a divided exhaust period turbocharging system controlled by a concentric cam system, and we presented several fixed speed/load point sets of results that demonstrated the expected BSFC benefits. The BSFC reductions (2.5% to 4%) correlated to reduction in pumping work and to improvement in combustion phasing at knock-limited points from substantial reductions in Residual Gas Fraction compared to the conventionally-boosted baseline engine. In this paper we present additional results from engine tests in the areas of full-load performance and emissions with and without Scavenge-sourced EGR. To demonstrate the WOT performance potential of a VEMB engine, we show the effect of turbocharger matching steps, with results that exceed the baseline engine output across the engine speed range.

Using a 3 liter, 4 valves per cylinder, V6 Diesel engine model, this study investigates late intake valve closing (LIVC) time in an effort to reduce the fuel consumption of the engine. Two different intake cam duration technologies for diesel engines are evaluated using a 1-D engine simulation software code. The first method utilized for duration control delays the effective closing of the intake valve by moving one intake cam lobe with respect to the other baseline intake cam lobe. In the second method, the closing of both intake valves is delayed by the introduction of an adjustable dwell period during the closing portion of the valve motion. During this mid-lift dwell period, the lift is held at a constant value until it goes into the closing phase. The systems are evaluated and compared at 4 operating points of varying engine speed and load. At each operating point, while engine load is held constant, intake valve closing time is varied.

The tractor trailer models discussed in this paper were for a real-time hardware-in-the-loop (HIL) simulation to test heavy truck electronic stability control (ESC) systems [1]. The accuracy of the simulation results relies on the fidelity and accuracy of the vehicle parameters used. However in this case where hardware components are part of the simulation, their accuracy also affects the proper working of the simulation and ESC unit. Hence both the software and hardware components have to be validated. The validation process discussed in this paper is divided into two sections. The first section deals with the validation of the TruckSim vehicle model, where experimental data is compared with simulation results from TruckSim. Once the vehicle models are validated, they are incorporated in the HIL simulation and the second section discusses the validation of the whole HIL system with ESC.

Typical factors that contribute to the coast down characteristics of a vehicle include aerodynamic drag, gravitational forces due to slope, pumping losses within the engine, frictional losses throughout the powertrain, and tire rolling resistance. When summed together, these reactions yield predictable deceleration values that can be related to vehicle speeds. This paper focuses on vehicle decelerations while coasting with a typical medium-sized SUV. Drag factors can be classified into two categories: (1) those that are caused by environmental factors (wind and slope) and (2) those that are caused by the vehicle (powertrain losses, rolling resistance, and drag into stationary air). The purpose of this paper is to provide data that will help engineers understand and model vehicle response after loss of engine power.

A laboratory experiment is designed to examine the clunk phenomenon. A static torque is applied to a driveline system via the mass of an overhanging torsion bar and electromagnet. Then an applied load may be varied via attached mass and released to simulate the step down (tip-out) response of the system. Shaft torques and torsional and translational accelerations are recorded at pre-defined locations. The static torque closes up the driveline clearances in the pinion/ring (crown wheel) mesh. With release of the applied load the driveline undergoes transient vibration. Further, the ratio of preload to static load is adjusted to lead to either no-impact or impact events. Test A provides a ‘linear’ result where the contact stiffness does not pass into clearance. This test is used for confirming transient response and studying friction and damping. Test B is for mass release with sufficient applied torque to pass into clearance, allowing the study of the clunk.

In-cylinder charge motion is known to significantly increase turbulence intensity, accelerate combustion rate, and reduce cyclic variation. This, in turn, extends the tolerance to exhaust gas recirculation (EGR), while the introduction of EGR results in much lowered nitrogen oxide (NOx) emissions and reduced fuel consumption. The present study investigates the effect of charge motion in a spark ignition engine on fuel consumption, combustion, and engine-out emissions with stoichiometric and EGR-diluted mixtures under part-load operating conditions. Experiments have been performed with a Chrysler 2.4L 4-valve I4 engine under 2.41 bar brake mean effective pressure at 1600 rpm over a spark range around maximum brake torque timing. The primary intake runners are partially blocked to create different levels of tumble, swirl, and cross-tumble (swumble) motion in the cylinder before ignition.

This paper describes the development and implementation of an accurate and repeatable path-following algorithm focused ultimately on vehicle testing. A compact, lightweight, and portable hardware package allows easy installation and negligible impact on the vehicle mass, even for the smallest automobile. Innovative features include the ability to generate a smooth, evenly-spaced path vector regardless the quality of the given path. The algorithm proposed in this work is suitable for testing in a controlled environment. The system was evaluated in simulation and performed well in road tests at low speeds.

Diesel engines nowadays are faced with enhanced emission standards, which limit further improvements in fuel economy. In order to meet future emission regulations in a cost effective way, high levels of EGR are needed. One way of increasing the level of EGR with current technology boosting systems is to utilize low pressure loop EGR. This paper discusses the benefits of low pressure loop EGR as well as some of the challenges. A new component is presented which overcomes some of these challenges. Also, modifications to current technology compressor wheels are presented which enable the compressor wheel to survive ingestion of exhaust gas.

Control strategies for engines with multiple sources of EGR (Hybrid EGR), such as high and low pressure, have been developed and are in or near production. Next generation engines require these basic approaches be extended to take advantage of the capabilities these advanced air systems offer. This paper presents a number of the practical challenges encountered when attempting to do this control system optimization as well as proposed solutions. Engine test results showing the net improvements to emissions and transient response when using these techniques are discussed.

Despite a large body of analytical work characterizing the dynamic motion of planetary gears, supporting experimental data is limited. Experimental results are needed to support computer modeling and offer practical optimization guidelines to gear designers. This paper presents the design and implementation of a test facility and precision test fixtures for accurate measurement of planetary gear vibration at operating conditions. Acceleration measurements are made on all planetary bodies under controlled torque/speed conditions. Custom, high-precision test fixtures accommodate instrumentation, ensure accurate alignment, help isolate gear dynamics, and allow for variability in future testing. Results are compared with finite element and lumped parameter models.

Prior work with the concept of dividing the exhaust process into an early and late phase has shown the potential of applying only the early stage (blow-down) of the exhaust period directly to a turbocharger or turbocharger system, and the later stage (scavenge) arranged to bypass the turbine. In this manner, the exhaust backpressure required to extract high turbine work from the engine can be isolated from the displacement phase of the exhaust stroke and thereby greatly reduce the exhaust pumping work and Residual Gas Fraction. In previously-published efforts, the challenges of valve-event control and high turbine inlet temperature have been revealed. The BorgWarner Engine Systems Group, in conjunction with Presta, has applied a cam-phaser controlled concentric camshaft system to the exhaust side of a divided exhaust port 4-valve per cylinder DOHC GDI engine, to enable variable phasing between the Blow-down and Scavenge cam profiles.

This study investigates the autoignition of Primary Reference Fuels (PRFs) using a detailed kinetic model. The chemical kinetics software CHEMKIN is used to facilitate solutions in a constant volume reactor and a variable volume reactor, with the latter representing an IC engine. Experimental shock tube and HCCI engine data from literature is compared with the present predictions in these two reactors. The model is then used to conduct a parametric study in the constant volume reactor of the effect of inlet pressure, inlet temperature, octane number, fuel/air equivalence ratio, and exhaust gas recirculation (EGR) on the autoignition of PRF/air mixtures. A number of interesting characteristics are demonstrated in the parametric study. In particular, it is observed that PRFs can exhibit single or two stage ignition depending on the inlet temperature. The total ignition delay, whether single or two stage, is correlated withn-C7H16/O2 ratio.

This paper presents the details of the model for the physical steering system used on the National Advanced Driving Simulator. The system is basically a hardware-in-the-loop (steering feedback motor and controls) steering system coupled with the core vehicle dynamics of the simulator. The system's torque control uses cascaded position and velocity feedback and is controlled to provide steering feedback with variable stiffness and dynamic properties. The reference model, which calculates the desired value of the torque, is made of power steering torque, damping function torque, torque from tires, locking limit torque, and driver input torque. The model also provides a unique steering dead-band function that is important for on-center feel. A Simulink model of the hardware/software is presented and analysis of the simulator steering system is provided.