Search Results

Compression molded SMC composed of chopped carbon fiber and resin polymer which balances the mechanical performance and manufacturing cost presents a promising solution for vehicle lightweight strategy. However, the performance of the SMC molded parts highly depends on the compression molding process and local microstructure, which greatly increases the cost for the part level performance testing and elongates the design cycle. ICME (Integrated Computational Material Engineering) approaches are thus necessary tools to reduce the number of experiments required during part design and speed up the deployment of the SMC materials. As the fundamental stage of the ICME workflow, commercial software packages for SMC compression molding exist yet remain not fully validated especially for chopped fiber systems. In the present study, SMC plaques are prepared through compression molding process.

Chopped carbon fiber sheet molding compound (SMC) material is a promising material for mass-production lightweight vehicle components. However, the experimental characterization of SMC material property is a challenging task and needs to be further investigated. There now exist two ASTM standards (ASTM D7078/D7078M and ASTM D5379/D5379M) for characterizing the shear properties of composite materials. However, it is still not clear which standard is more suitable for SMC material characterization. In this work, a comparative study is conducted by performing two independent Digital Image Correlation (DIC) shear tests following the two standards, respectively. The results show that ASTM D5379/D5379M is not appropriate for testing SMC materials. Moreover, the failure mode of these samples indicates that the failure is caused by the additional moment raised by the improper design of the fixture.

An energy-regenerative vehicle suspension is proposed. Permanent-magnet direct-current motors are utilized as the active actuators in automotive suspension. The significant characteristic of the suspension is that vibration energy from the road excitation can be regenerated and transformed into electric energy while good suspension performance can be maintained. The modeling of electrical suspension system has been completed and simulated in Matlab/Simulink. The motor actuator working as a generator is proved to maintain the performance of vibration control and energy-regeneration. The prototype of motor actuator is designed and made. The vibration absorption and regeneration performances are verified by full-vehicle experiments.

To advance vehicle lightweighting, chopped carbon fiber sheet molding compound (SMC) is identified as a promising material to replace metals. However, there are no effective tools and methods to predict the mechanical property of the chopped carbon fiber SMC due to the high complexity in microstructure features and the anisotropic properties. In this paper, a Representative Volume Element (RVE) approach is used to model the SMC microstructure. Two modeling methods, the Voronoi diagram-based method and the chip packing method, are developed to populate the RVE. The elastic moduli of the RVE are calculated and the two methods are compared with experimental tensile test conduct using Digital Image Correlation (DIC). Furthermore, the advantages and shortcomings of these two methods are discussed in terms of the required input information and the convenience of use in the integrated processing-microstructure-property analysis.

Brake squeal is an instability issue with many parameters. This study attempts to assess the effect of thermal load on brake squeal behavior through finite element computation. The research can be divided into two parts. The first step is to analyze the thermal conditions of a brake assembly based on ANSYS Fluent. Modeling of transient temperature and thermal-structural analysis are then used in coupled thermal-mechanical analysis using complex eigenvalue methods in ANSYS Mechanical to determine the deformation and the stress established in both the disk and the pad. Thus, the influence of thermal load may be observed when using finite element methods for prediction of brake squeal propensity. A detailed finite element model of a commercial brake disc was developed and verified by experimental modal analysis and structure free-free modal analysis.

ADAS must be tested thoroughly before they can be deployed for series production. Comparing with road and field test, bench test has been widely used owing to its advantages of less labor costs, more controllable scenarios, etc. However, there is no satisfied systematic approach to generate high-efficiency and full-coverage test scenarios automatically because of its integration of human, vehicle and traffic. Most of the test scenarios generated by the existing methods are either too simple or too few to be able to achieve full coverage of requirements. Besides, the cost is high when the ET method is used. To solve the aforementioned problems, an automatic test scenario generation method based on complexity for bench test is presented in this paper. Firstly, considering the fact that the device is easier to malfunction under complex cases, an index measuring the complexity of test case is proposed by using the method of AHP.

This paper proposes a low-cost but indirect method for occupancy detection and occupant counting purpose in current and future automotive systems. It can serve as either a way to determine the number of occupants riding inside a car or a way to complement the other devices in determining the occupancy. The proposed method is useful for various mobility applications including car rental, fleet management, taxi, car sharing, occupancy in autonomous vehicles, etc. It utilizes existing on-board motion sensor measurements, such as those used in the vehicle stability control function, together with door open and closed status. The vehicle’s motion signature in response to an occupant’s boarding and alighting is first extracted from the motion sensors that measure the responses of the vehicle body. Then the weights of the occupants are estimated by fitting the vehicle responses with a transient vehicle dynamics model.

This paper presents a road classifier based on the system response with consideration of the tire enveloping. The aim is to provide an easily applicable yet accurate road classification approach for automotive engineers. For this purpose, tire enveloping effect is firstly modeled based on the flexible roller contact (FRC) theory, then transfer functions between road input and commonly used suspension responses i.e. the sprung mass acceleration, unsprung mass acceleration, and rattle space, are calculated for a quarter vehicle model. The influence of parameter variations, vehicle velocity, and measurement noise on transfer functions are comprehensively analyzed to derive the most suitable system response thereafter. In addition, this paper proposes a vehicle speed correction mechanism to further improve the classification accuracy under complex driving conditions.

Due to traffic congestion and environmental pollution, connected automated vehicle (CAV) technologies based on vehicle-to-vehicle (V2V) and vehicle-to-infrastructure communication (V2I) have gained increasing attention from both academia and industry. Connected hybrid electric vehicles (CHEVs) offer great opportunities to reduce vehicular operating costs and emissions. However, in complex traffic scenarios, high-quality real-time energy management of CHEVs remains a technical challenge. To address the challenge, this paper proposes a hierarchical eco-driving strategy that consists of speed planning and energy management layers. At the upper layer, by leveraging the real-time traffic data provided by vehicle-to-everything (V2X) communication, dynamic traffic constraints are predicted by the traffic flow predictor developed based on the Hankel dynamic mode decomposition algorithm (H-DMD).

According to driving scenarios, intelligent vehicle is mainly applied on urban driving, highway driving and close zone driving, etc. As one of the most valuable developments, automated highway driving has great progress. This paper focuses on automated highway driving decision, and considering decision efficiency and feasibility, a hierarchical motion planning algorithm based on dynamic programming was proposed, and simultaneously, road coordinate transformation methods were developed to deal with complex road conditions. At first, all transportation user states are transformed into straight road coordinate to simplify modeling and planning, then a set of candidate paths with Bezier form was developed and with the help of obstacles motion prediction, the feasible target paths with collision-free were remains, and via comparing vehicle performance for feasible path, the optimal driving trajectory was generated.

As a crucial part of the intelligent transportation system, traffic signal control will realize the boundary control of the traffic area, it will also lead to delays and excessive fuel consumption when the vehicle is driving at the intersection. To tackle this challenge, this research provides an optimized control framework based on reinforcement learning method and speed guidance strategy for the connected vehicle network. Prior to entering an intersection, vehicles are focused on in a specific speed guidance area, and important factors like uniform speed, acceleration, deceleration, and parking are optimized. Conclusion, derived from deep reinforcement learning algorithm, the summation of the length of the vehicle’s queue in front of the signal light and the sum of the number of brakes are used as the reward function, and the vehicle information at the intersection is collected in real time through the road detector on the road network.

Self-pierced rivet (SPR) and adhesive are two important joining technologies widely used in automobile industry, and they are often used together to form a hybrid joint. SPR and adhesives can often be used in close proximity in a component, leading to an interaction of the two joints. This interaction can influence the corrosion and noise, vibration and harshness (NVH) characteristics of the structure, as well as its strength and durability. In this paper, the stress distribution in an SPR-adhesive hybrid joint is evaluated by using the finite element method, and then compared with that in an adhesive joint. Results indicate that the stress concentrates at the edge of adhesive layer in hybrid joint and adhesive joint and around the rivet in an SPR joint. The effect of rivet is numerically investigated by either removing the rivet from the hybrid joint or changing the position of the rivet on the overlapping area.

Function and performance test of automated vehicles in the closed field is a necessary way to verify their safety, intelligence and comfort. The design and number of test scenarios will influence if the automated vehicles can be tested and evaluated effectively and fast. Based on the interrelationship among the vehicle, driver’s (or control system) driving strategy and road, we use the permutation and combination method to compare the relative position and movement relations between an automated vehicle (vehicle under test) and the surrounding vehicles to generate a total possible test scenarios group.

The design optimization of vehicle body structure is addressed to reduce interior noise and improve customer satisfaction in this paper. The structural-acoustic model is established and the response of sound pressure in frequency domain is obtained by using finite element method. The minimization of sound pressure near the driver's right ear depends on the geometry of vehicle body structure and the layout of damping treatments. The panel participation analysis is performed to find out the key panels as design variables and improve the efficiency of optimization computation. Response Surface Method (RSM) is utilized to optimize the vibro-acoustic properties of vehicle body structure instead of complex structural-acoustic coupling finite element model. Geometric optimization problem of panels is described and solved to minimize the interior noise in vehicle.

In order to measure the noise of auto shock absorbers, a test bench used to detect piston-rod vibration responses of shock absorbers and measuring analyzer named SANTS-I were developed. The vibration response data was detected by bench tests, which shows that there are high-frequency violent peaks on the sine curve of piston-rod oscillating with relative low frequency. In order to explain the interior work dynamic mechanism of shock absorbers, a schematic Micro-process Dynamic Model with 10 steps particularly divided extension and compression stroke in more detail, and dynamic differential equations for each step were presented and discussed. Furthermore, numerical simulation for the inner impacts interaction between piston and damping fluid of hydraulic shock absorber was realized by ADINA software, by the establishment of a gas-liquid two-phase finite element model.

The diesel premixed low-temperature combustion mode avoids the generation of thick mixture and the high temperature region in which a great amount of NOx and PM generates. It makes a significant reduction in the emissions of both NOx and PM available at the same time. However, with the quantity of pre-injection increases and the injection time advances, the emission of HC increases significantly, which causes a decrease in the combustion efficiency. Studies have shown that the flame quench caused by too thick or too lean mixture and the oil film on the chamber is the main source for the emission of HC. As a result, understanding the mechanism of atomization and evaporation of the fuel and the formation of the mixture makes significant sense. This paper focuses on the mixture formation process. And the methods of testing the distribution of the mixture, the influential factors and control methods are studied.

The design optimization of vehicle body structure is addressed to reduce interior noise and improve customer satisfaction in this paper. The structural-acoustic model is developed by using finite element method. The frequency response of structural-acoustic system is computed by modal analysis method. The optimization problem is constructed to minimize the sound pressure level in the right ear of the driver. The sensitivity analysis is carried out to find the key panels to be optimized as design variables and improve the efficiency of optimization computation. Response Surface Method (RSM) is utilized to develop the surrogate model and optimize the vehicle Noise Vehicle and Harshness (NVH) behavior. A 9dB reduction of sound pressure level (SPL) in the right era of the driver is obtained through geometric optimization for panels. Furthermore, the topology optimization model is developed to search the optimal layout of constrained layer damping treatments in the front floor.

Sound quality of vehicle interior noise affects passenger comfort. In order to improve the sound quality of a micro commercial vehicle, the vehicle interior noise under different conditions such as idle, constant speeds and accelerating is recorded by using artificial head with dual microphones. The sound quality of recorded noise is evaluated in both objective and subjective ways. Physical parameters of interior noise are calculated objectively, and annoyance score is analyzed subjectively using paired-comparison method. According to the regression analyzing of the annoyance score and the physical parameters, an objective evaluation parameter of the sound quality is employed. To analyze the vehicle body panel contribution to interior noise sound quality, the location and spectrum characteristics of major panel emission noise sources are identified based on partial singular valued decomposition (PSVD) method.

In recent years, with the increase of traffic accidents and traffic jams, lane change, as one of the most important and commonly automatic driving operations for autonomous vehicles, is receiving attention in academia. It is considered to be one of the important solutions that play an important role in improving road traffic safety and efficiency. However, most existing lane-changing models are rule-based lane-changing models. These models only assume a one-direction impact of surrounding vehicles on the lane-changing vehicle. In fact, lane change is a process of mutual interaction between vehicles due to the complexity and uncertainty of the traffic environment. Moreover, the safety and efficiency of existing lane-changing decision algorithms need to be improved. In this paper, we proposed a multivehicle cooperative control approach with a distributed control structure to control the model.

The heat pump with low global warming potential (GWP) refrigerants is imperative for the electric vehicle (EV) to slow down global warming and extend the driving range while meeting passengers' thermal comfort in low ambient temperatures. However, there are no appropriate refrigerants. To provide long-term and environmental-friendly refrigerants in the heat pump for EVs, herein, we reported newly developed low-GWP refrigerant mixtures, i.e., DL3B, whose GWP is lower than 140, the flammability (lower flammability limit and burning velocity), saturation pressure, lubricant miscibility, material compatibility were experimentally tested. A test bench that can investigate the performance of an R410A prototype was built. The drop-in tests of the DL refrigerant were carried out to evaluate the capacities and COPs for both cooling and heating modes in the EV heat pump system.