Search Results

In the U.S., the teenage driving population is at the highest risk of being involved in a crash. Teens often demonstrate poor vehicle control skills and poor ability to identify hazards, thus proper understanding of automotive indicators and warnings may be even more critical for this population. This research evaluates teen drivers’, between 15 to 17 years of age, understanding of symbols from vehicles featuring advanced driving assistant systems and multiple powertrain configurations. Teen drivers’ (N=72) understanding of automotive symbols was compared to three other groups with specialized driving experience and technical knowledge: automotive engineering graduate students (N=48), driver rehabilitation specialists (N=16), and performance driving instructors (N=15). Participants matched 42 symbols to their descriptions and then selected the five symbols they considered most important.

Driving inattention caused by drowsiness has been a significant reason for vehicle crash accidents, and there is a critical need to augment driving safety by monitoring driver drowsiness behaviors. For real-time drowsy driving awareness, we propose a vision-based driver drowsiness monitoring system (DDMS) for driver drowsiness behavior recognition and analysis. First, an infrared camera is deployed in-vehicle to capture the driver’s facial and head information in naturalistic driving scenarios, in which the driver may or may not wear glasses or sunglasses. Second, we propose and design a multi-modal features representation approach based on facial landmarks, and head pose which is retrieved in a convolutional neural network (CNN) regression model. Finally, an extreme learning machine (ELM) model is proposed to fuse the facial landmark, recognition model and pose orientation for drowsiness detection. The DDMS gives promptly warning to the driver once a drowsiness event is detected.

A wet clutch model is required in automotive propulsion system simulations for enabling robust design and control development. It commonly assumes Coulomb friction for simplicity, even though it does not represent the physics of hydrodynamic torque transfer. In practice, the Coulomb friction coefficient is treated as a tuning parameter in simulations to match vehicle data for targeted conditions. The simulations tend to deviate from actual behaviors for different drive conditions unless the friction coefficient is adjusted repeatedly. Alternatively, a complex hydrodynamic model, coupled with a surface contact model, is utilized to enhance the fidelity of system simulations for broader conditions. The theory of elastic asperity deformation is conventionally employed to model clutch surface contact. However, recent examination of friction material shows that the elastic modulus of surface fibers significantly exceeds the contact load, implying no deformation of fibers.

Vehicle to Vehicle Communication use case performance heavily relies on market penetration rate. The more vehicles support a use case, the better the customer experience. Enabling these use cases with acceptable quality on vehicles without built-in navigation systems, elaborate map matching and highly accurate sensors is challenging. This paper introduces a simulation framework to assess system performance in dependency of vehicle positioning accuracy for matching approach path traces in Decentralized Environmental Notification Messages (DENMs) in absence of navigation systems supporting map matching. DENMs are used for distributing information about hazards on the road network. A vehicle without navigation system and street map can only match its position trajectory with the trajectory carried in the DENM.

Morphological features of voids were characterized for T300/924 12-ply and 16-ply composite laminates at different porosity levels through the implementation of a digital microscopy (DM) image analysis technique. The composite laminates were fabricated through compression molding. Compression pressures of 0.1MPa, 0.3MPa, and 0.5MPa were selected to obtain composite plaques at different porosity levels. Tension-tension fatigue tests at load ratio R=0.1 for composite laminates at different void levels were conducted, and the dynamic stiffness degradation during the tests was monitored. Fatigue mechanisms were then discussed based on scanning electron microscope (SEM) images of the fatigue fracture surfaces. The test results showed that the presence of voids in the matrix has detrimental effects on the fatigue resistance of the material, depending on the applied load level.

This paper argues the importance of engineering heuristics and introduces an educational data-driven tool to help novice engineers develop their engineering heuristics more effectively. The main objective in engineering practice is to identify opportunities for improvement and apply methods to effect change. Engineers do so by applying ‘how to’ knowledge to make decisions and take actions. This ‘how to’ knowledge is encoded in engineering heuristics. In this paper, we describe a tool that aims to provide heuristic knowledge to users by giving them insight into heuristics applied by experts in similar situations. A repository of automotive data is transformed into a tool with powerful search and data visualization functionalities. The tool can be used to educate novice automotive engineers alongside the current resource intensive practices of teaching engineering heuristics through social methods such as an apprenticeship.

Autonomous Vehicles (AVs) operate based on image information and 3D maps generated by sensors like cameras, LIDARs and RADARs. This information is processed by the on-board processing units to provide the right actuation signals to drive the vehicle. For safe operation, these sensors should provide continuous high quality data to the processing units without interruption in all driving conditions like dust, rain, snow and any other adverse driving conditions. Any contamination on the sensor surface/lens due to rain droplets, snow, and other debris would result in adverse impact to the quality of data provided for sensor fusion and this could result in error states for autonomous driving. In particular, snow is a common contamination condition during driving that might block a sensor surface or camera lens. Predicting and preventing snow accumulation over the sensor surface of an AV is important to overcome this challenge.

With the rapid development of artificial intelligence, the autonomous vehicles (AV) have attracted considerable attention in the automotive industry. However, different factors negatively impact the adoption of the AVs, delaying their successful commercialization. Accretion of atmospheric icing, especially wet snow, on AV sensors causes blockage on their lenses, making them prone to lose their sight, in turn, increasing potential chances of accidents. In this study, two different designs are proposed in order to prevent snow accretion on the lenses of AVs via air flow across the lens surface. In both designs, lenses made of plain glass and superhydrophobic coated glass surfaces are tested. While some researchers have shown promise of water repellency on superhydrophobic surfaces, more snow accretion is observed on the superhydrophobic surfaces, when compared to the plain glass lenses.

As an alternative lightweight material, chopped carbon fiber reinforced Sheet Molding Compound (SMC) composites, formed by compression molding, provide a new material for automotive applications. In the present study, the monotonic and fatigue behavior of chopped carbon fiber reinforced SMC is investigated. Tensile tests were conducted on coupons with three different gauge length, and size effect was observed on the fracture strength. Since the fiber bundle is randomly distributed in the SMC plaques, a digital image correlation (DIC) system was used to obtain the local modulus distribution along the gauge section for each coupon. It was found that there is a relationship between the local modulus distribution and the final fracture location under tensile loading. The fatigue behavior under tension-tension (R=0.1) and tension-compression (R=-1) has also been evaluated.

With the dramatic increase in vehicle technology, the availability of a wide range of powertrains, and the development of advanced driver assistant systems (ADAS), instrument cluster interfaces have become more complex, increasing the demand on drivers. Understanding the needs and preferences of a diverse group of drivers is essential for the development of digital instrument cluster interfaces that improve driver’s understanding of critical information about the vehicle. This study investigated drivers’ understanding and preferences related to powertrain and ADAS symbols presented on instrument clusters. Participants answered questions that evaluated nine symbol’s comprehension, familiarity, and helpfulness. Then, participants were presented with information from the owner’s manual for each symbol and responded if the information changed their understanding of the symbol.

The effect of friction modifiers on the low-speed frictional properties of automatic transmission fluids (ATFs) was investigated by scanning force microscopy (SFM). A clutch lining material was covered by a droplet of test ATF, and a steel tip was scanned over the sample. The scanning speeds were varied from 0.13 to 8.56 mm /sec, and the frictional force was deduced from the torsion of the SFM cantilever. A reduction in dynamic friction due to the addition of the friction modifier was clearly observed over the entire speed range. This indicates that the boundary lubrication mechanism is dominant under this condition, and therefore surface-active friction modifiers can effectively improve the frictional characteristics. The friction reduction was more pronounced at lower sliding speeds. Thus addition of friction modifiers produced a more positive slope in the μ-ν (friction vs. sliding speed) plots, and would contribute to make wet clutch systems less susceptible to shudder vibrations.

Stress analyses of complex automotive components can be nearly impossible to achieve due to extreme difficulties in generating a realistic finite element model. A digital image based finite element approach was used to generate a 3-D finite element model from computed tomography (CT) scans of two automotive transmission cases. For the first case, original CT slices of 1024x1024x208 provided by ARACOR Inc. (Sunnyvale, CA) were used to generate a 3-D finite element model containing nearly 400,000 8-node brick elements. For the second case, 770x870x759 CT slices were used to generate a 3-D finite element model containing approximately 650,000 3-D elements. The mesh data generation from CT data for both cases took 6 minutes each on an engineering workstation. The resulting finite element meshes were analyzed using a specially designed finite element equation solver.

With the increasing demand for safety, energy saving and emission reduction, Advanced High Strength Steels (AHSS) have become very attractive materials for automobile makers. Welding of AHSS remains one of the technical challenges in the successful application of AHSS in automobile structures, especially when durability of the welded structures is required. In this study, 2.0 mm uncoated DP780 was investigated. GMAW welding parameters for lap joints of this steel were developed in order to obtain different weld geometries defined by weld toe angle, weld leg sizes, and weld penetration. Metallurgical properties of the joints were evaluated using optical microscopy and scanning electron microscopy (SEM). Static and fatigue tests were conducted on the welded joints. Effect of weld geometry and HAZ softening on fatigue performance including fatigue life, crack initiation site and propagation path of the joints will be analyzed.

A methodology is developed that incorporates high resolution CFD flowfield information and a particle trajectory simulation, aimed at addressing Paint Transfer Efficiency (PTE) for bell sprayers. Given a solid model for the bell sprayer, the CFD simulation, through automeshing, determines a high resolution Cartesian volume mesh (14-20 million cells). With specified values of the initial shaping air, transient and steady-state flow field information is obtained. A particle trajectory visualization tool called SpraySIM uses this complicated flowfield information to determine the particle trajectories of the paint particles under the influence of drag, gravity and electrostatic potential. The sensitivity of PTE on shaping air velocity, charge-to-mass ratio, potential, and particle diameter are examined.

Typical automotive joints are lap, coach, butt and miter joints. In tubular joining applications, a coach joint is common when one tube is joined to another tube without the use of brackets. Various fusion joining processes are popular in joining coach joints. Common fusion joining processes are Gas Metal Arc Welding (GMAW), Laser and Laser Hybrid, and Gas Tungsten arc welding (GTAW). In this study, fusion welded 2.0 mm uncoated DP780 steel coach joints were investigated. Laser, Gas metal arc welding (GMAW), and laser hybrid (Laser + GMAW) welding processes were selected. Metallurgical properties of the DP780 fusion welds were evaluated using optical microscopy. Static and fatigue tests were conducted on these joints for all three joining processes. It was found that joint fit-up, type of welding process, and process parameters, especially travel speed, have significant impact on static and fatigue performance of the coach joints in this study.

Wavelets are a powerful mathematical tool used to multi-resolution time-frequency decomposition of signals, in order to analyze them in different scales and obtain different aspects of the information. Despite being a relatively new tool, wavelets have being applied in several areas of human knowledge, especially in signal processing, with emphasis in encoding and compression of image, video and audio. Based on a previous successful applications (FRAZIER, 1999) together a commitment to quality results, this paper evaluates the use of the Discrete Wavelet Transform (DWT) as an compression algorithm to reduce the amount of data collected in road load signals (load history) which are used by the durability engineering teams in the automotive industry.

Noise source identification has been a subject well studied in the past few years. Automobile manufactures along with specialized supplies have been developed some methods in this matter. The importance of such subject is quite obvious, especially in the auto industry: identify potential problems and point out solutions for NVH. There are several methods of noise source identification widely used. Among them, one can mention "Hotspot Search," which consists of noise intensity measurement, mapping and ranking the relative contribution of each substructure of one body. Another method used, one can point out is the STSF (Spatial Transformation of Sound Fields). It consists of a measurement over a scan plane using a set of microphone array. In this way, a 2D sound field can be transformed in a 3D description and source direction can be identified.

Velocity profiles for air flowing under a vehicle body are determined by analyzing videotapes of neutrally buoyant soap bubbles using motion analysis software and equipment. What had heretofore been primarily a qualitative flow visualization technique has been extended to provide quantitative data. The light sources, cameras, and bubble generator, mounted on the vehicle, are powered by the vehicle's electrical system, making it possible to compare underbody velocities measured in a wind tunnel with those over the road. Results are presented for a heavy-duty 4×4 pickup truck at speeds up to 25m/s (55 mph). The velocity profiles in the tunnel and on the road were quite similar.

Scalograms based on shift-invariant orthonormal wavelet transforms can be used to analyze impulsive and transient sounds in the presence of more stationary sound backgrounds, such as wind noise or drivetrain noise. The visual threshold of detection for impulsive features on the scalogram (signal energy content vs. time and frequency,) is shown to be similar to the audible threshold of detection of the human auditory system for the corresponding impulsive sounds. Two examples of impulsive sounds in a realistic automotive sound background are presented: automotive interior rattle in a vehicle passenger compartment, and spark knock recorded in an engine compartment.

Piston wetting can be isolated from the other sources of HC emissions from DISI engines by operating the engine predominantly on a gaseous fuel and using an injector probe to impact a small amount of liquid fuel on the piston top. This results in a marked increase in HC emissions. In a previous study, we used a variety of pure liquid hydrocarbon fuels to examine the influence of fuel volatility and structure on the HC emissions due to piston wetting. It was shown that the HC emissions correspond to the Leidenfrost effect: fuels with very low boiling points yield high HCs and those with a boiling point near or above the piston temperature produce much lower HCs. All of these prior tests of fuel effects were performed at a single operating condition: the Ford World Wide Mapping Point (WWMP). In the present study, the effects of load and engine speed are examined.