Search Results

In an automotive cooling circuit, the wax melting process determines the net and time history of the energy transfer between the engine and its environment. A numerical process that gives insight into the mixing process outside the wax chamber, the wax melting process inside the wax chamber, and the effect on the poppet valve displacement will be advantageous to both the engine and automotive system design. A fully three dimensional, transient, system level simulation of an inlet controlled thermostat inside an automotive cooling circuit is undertaken in this paper. A proprietary CFD algorithm, Simerics-Sys®/PumpLinx®, is used to solve this complex problem. A two-phase model is developed in PumpLinx® to simulate the wax melting process. The hysteresis effect of the wax melting process is also considered in the simulation.

The airflow that enters the front grille of a ground vehicle for the purpose of component cooling has a significant effect on aerodynamic drag. This drag component is commonly referred to as cooling drag, which denotes the difference in drag measured between open grille and closed grille conditions. When the front grille is closed, the airflow that would have entered the front grille is redirected around the body. This airflow is commonly referred to as cooling interference airflow. Consequently, cooling interference airflow can lead to differences in vehicle component drag; this component of cooling drag is known as cooling interference drag. One mechanism that has been commonly utilized to directly influence the cooling drag, by reducing the engine airflow, is active grille shutters (AGS). For certain driving conditions, the AGS system can restrict airflow from passing through the heat exchangers, which significantly reduces cooling drag.

In this paper, a systems engineering approach is explored to evaluate the effect of design parameters that contribute to the performance of the embedded Automatic Speech Recognition (ASR) engine in a vehicle. This includes vehicle designs that influence the presence of environmental and HVAC noise, microphone placement strategy, seat position, and cabin material and geometry. Interactions can be analyzed between these factors and dominant influencers identified. Relationships can then be established between ASR engine performance and attribute performance metrics that quantify the link between the two. This helps aid proper target setting and hardware selection to meet the customer satisfaction goals for both teams.

This paper describes two case studies in which multiple microphone processing (beamforming) and microphone location were evaluated to determine their impact on improving embedded automatic speech recognition (ASR) in a vehicle hands-free environment. While each of these case studies was performed using slightly different evaluation set-ups, some specific and general conclusions can be drawn to help guide engineers in selecting the proper microphone location and configuration in a vehicle for the improvement of ASR. There were some outcomes that were common to both dual microphone solutions. When considering both solutions, neither was equally effective across all background noise sources. Both systems appear to be far more effective for noise conditions in which higher frequency energy is present, such as that due to high levels of wind noise and/or HVAC (heating, ventilation and air conditioning) blower noise.

This paper describes a method to validate in-vehicle speech recognition by combining synthetically mixed speech and noise samples with batch speech recognition. Vehicle cabin noises are prerecorded along with the impulse response from the driver's mouth location to the cabin microphone location. These signals are combined with a catalog of speech utterances to generate a noisy speech corpus. Several factors were examined to measure their relative importance on speech recognition robustness. These include road surface and vehicle speed, climate control blower noise, and driver's seat position. A summary of the main effects from these experiments are provided with the most significant factors coming from climate control noise. Additionally, a Signal to Noise Ratio (SNR) experiment was conducted highlighting the inverse relationship with speech recognition performance.

Cooling drag is a metric that measures the influence of air flow travelling through the open grille of a ground vehicle on overall vehicle drag, both internally (engine air flow) and externally (interference air flow). With the interference effects considered, a vehicles cooling drag can be influenced by various air flow fields around the vehicle, not just the air flow directly entering or leaving the engine bay. For this reason, computational fluid dynamics (CFD) simulations are particularly difficult. With insights gained from a previously conducted set of experimental studies, a CFD validation effort was undergone to understand which air flow field characteristics contribute to CFD/test discrepancies. A Lattice-Boltzmann Large Eddy Simulation (LES) method was used to validate several test points. Comparison using integral force values, surface pressures, and cooling pack air mass flows was presented.

Among the many sources of uncertainty in an unsteady computational fluid dynamics (CFD) simulation, the statistical uncertainty in the mean value of a fluctuating quantity (for example, the drag coefficient) is of practical importance for vehicle design and development. This uncertainty can be reduced by extending the simulation run length, however, this increases the computational cost and leads to longer turnaround times. Moreover, it is desirable to be able to run an unsteady CFD simulation for the minimum amount of time necessary to reach an acceptable amount of uncertainty in the quantity of interest. This work assesses several methods for calculating the uncertainty in the mean of an unsteady signal. Simulated noise is used to validate the methods, and evaluation is carried out using signals from CFD simulations of realistic vehicle geometries. Calculating the uncertainty in the difference between two signals is also discussed.

To-date the primary challenge in conducting aerodynamic CFD simulations of actual vehicles with realistically complex geometry has been the construction of a computational mesh. The CAD-to-Mesh processes used to-date have been laborious, often requiring many weeks of engineering time. In this paper we present a new technique to greatly expedite the CAD-to-Mesh process. The fundamentals of this technique are discussed followed by case studies that show that this technique can reduce the engineering time required for the CAD-to-Mesh process to just a few hours.

To achieve optimal axial and bending crush performance using dual phase steels for components designed for crash energy absorption and/or intrusion resistance applications, the cross sections of the components need to be optimized. In this study, Altair HyperMorph™ and HyperStudy® optimization software were used in defining the shape design variables and the optimization problem setup, and non-linear finite element code LS-DYNA® software was used in crush simulations. Correlated crash simulation models were utilized and the square cross-section was selected as the baseline. The optimized cross-sections for bending and axial crush performance resulted in significant mass and cost savings, particularly with the application of dual phase steels.

This paper discusses the optimization of an automotive hydraulic steering pump pulley design for improved in-vehicle pump NVH performance. Levels of steering pump whine noise heard inside a vehicle were deemed objectionable. Vehicle and component transfer path analyses indicated that the dominant noise path for the whine noise was airborne in nature. Subsequent experimental modal analysis indicated that the steering pump pulley was a major contributor to the amount of radiated noise produced by the pump/pulley system. CAE analysis was used to further analyze the dynamic behavior of the pulley and develop an optimized design with decreased noise radiation efficiency. The results predicted with the CAE analysis were verified in-vehicle, resulting in a vehicle with acceptable steering pump whine noise performance.

The three-dimensional non-reacting flow field inside a typical dual-monolith automotive catalytic converter was simulated using finite difference analysis. The monolithic brick resistance was formulated from the pressure gradient of fully developed laminar duct-flow and corrected for the entrance effect. This correlation was found to agree with experimental pressure drop data, and was introduced as an additional source term into the non-dimensional momentum governing equation within the brick. Flow distribution within the monolith was found to depend strongly on the diffuser performance, which is a complex function of flow Reynolds number, brick resistance, and inlet pipe length and bending angles. A distribution index was formulated to quantify the degree of non-uniformity at selected test cases covering ranges of flow conditions, brick types, and inlet conditions.

Sunroof is placed in certain high-end vehicles to give user a better driving experience. All automakers are searching alternatives to reduce weight and cost in the vehicle, in which sunroofs are also impacted. Some alternatives are already applied, as a honeycomb paper used in some sunshades that presents benefits, as less weight and with a good cost reduction. Although, due the reduced weight for this part produced in this material, it shows more susceptibility to reproduce the vibration that vehicle propagates in movement, especially in bad condition roads. The sunroof assembly is dependent of the roof reinforcement and roof skin, but in this special case, the validation could be done in the components itself because the interaction of the sunshades is directly dependent of the other sunroof parts, as rails and front frame.

Squeak and rattle are two undesirable occurrences during component operation and during vehicle driving condition, resulting in one of the top complains from costumers. One common grievance could happen during the user exterior handle operation and during side door closing. The exterior handle system during the operation could generate a squeak between interface parts, if materials and geometric tolerances was not been carefully designed. Also, vibration generated during door closing effort, might generate squeak between parts since the reinforcement for exterior handle touches the outer sheet metal internally. For this reason several guidelines might be included to avoid potential noise condition for this system during vehicle lifetime as correct material reduce friction between parts, taking into consideration the geometric condition between parts. Plus, coupling system on handles two pieces should also be evaluated to avoid squeak during use.

A measurement technique is presented to detect and quantify piston pin tick noise, thereby aiding optimization of piston pin bushing design. Furthermore, the characteristics of two types of piston pin noise are described. The first is caused by excessive clearance between the pin and the connecting rod bushing. A noncircular clearance between the pin and the connecting rod bushing causes the second type of the piston pin tick noise. Finally, a process is discussed to consider pin tick in the design and verification of the piston and connecting rod assembly. The method presented could also be used to investigate other unusual engine noises.

In this paper, a new technology for the design of silent transaxles is developed, where topography optimization is adopted and an artificial parameter called β is proposed as an objective function, representing an upper bound of the surface velocity. The strategy of the optimization is to minimize β while getting the surface velocities less than β. as the constraints. A numerical example of reducing transaxle's radiated noise by using the new optimization technology is given in the paper. In the example, an entire Ford transaxle system was modeled numerically, where most internal components were included. First a modal frequency velocity analysis was conducted. Then an acoustic power analysis based on the Acoustic Transfer Vector (ATV) was carried out. Finally, a topography optimization based on the β - method for the transaxle was performed to minimize the radiated noise.

Many decisions need to be made when test track data is used to set up Squeak & Rattle evaluations of subsystems or components. These decisions are judgment-based so different people with different backgrounds and experience levels will make different decisions - few of which can be called right or wrong - but they are different which causes problems. Squeak & Rattle evaluation has become more scientific in recent years as subjective evaluation has been replaced by quantitative methods like N10 Loudness and shakers have become quiet. It is the authors' contention that the variations caused by different judgment calls can no longer be tolerated. Therefore a methodical process was developed which assures that different people will get the same results from the same set of test track data.

A computational design study, performed in conjunction with experiments, to reduce the howl noise caused by the roof rack crossbars of a production automobile is presented. This goals were to obtain insight into the flow phenomenon causing the noise, and to do a design iteration study that would lead to a small number of cross-section recommendations for crossbars that would be tested in the wind tunnel. The flow condition for this study is 0 yaw at 30 mph inlet speed, which experimentally gives the strongest roof rack howl for the vehicle considered for this study. The numerical results have been obtained using the commercial CFD/CAA software PowerFLOW. The simulation kernel of this software is based on the numerical scheme known as the Lattice Boltzmann Method (LBM), combined with a two-equation RNG turbulence model.

Rear Window Buffeting (RWB) is the low-frequency, high amplitude, sound that occurs in many 4-door vehicles when driven 30-70 mph with one rear window lowered. The goal of this paper is to demonstrate that the mechanisms of RWB are similar to that of sun roof buffeting and to describe the results of several actions suspected in contributing to the severity of RWB. Finally, the results of several experiments are discussed that may lend insight into ways to reduce the severity of this event. A detailed examination of the side airflow patterns of a small Sport Utility Vehicle (SUV) shows these criteria exist on a small SUV, and experiments to modify the SUV airflow pattern to reduce RWB are performed with varying degrees of success. Based on the results of these experiments, design actions are recommended that may result in the reduction of RWB.

This paper is related to a new concept for the steering linkage of light trucks featuring mono-beam front axles. The current configuration of steering systems for those vehicles comprise a worm and sector steering with a Pitman arm connected to a transverse drag link. This last one connects to the steering link that finally steers the left and right wheels. The problem that has been experienced with this system is that, during a braking event, results in a very unfavorable bump steering condition.

This work is focused on the computer aided engineering noise and vibration control area (CAE-NVH), which is one of the most important in the automobile industry. The reason for that relevancy is that the noise and vibration effects can be directly perceived by the costumer. The vibration of the seats and steering wheel, as well as audible noises are some examples of factors that can cause discomfort to the driver. During the early design of a car, the systems are designed in a way to reach a good modal management level in order to avoid resonance problems. The finite element models, used to predict these resonances, are normally generated using only deterministic values for the model parameters such as stiffnesses, thicknesses and masses. However, these properties have an uncertainty due to the manufacturing process which is, in most cases, not taken into consideration during the design.