Search Results

Proportional integral derivative (PID) control technique is the most common control algorithm applied in various engineering applications. Also, particle swarm optimization (PSO) is extensively applied in various optimization problems. This paper introduces an investigation into the use of a PSO algorithm to tune the PID controller for a semi-active vehicle suspension system incorporating magnetorheological (MR) damper to improve the ride comfort and vehicle stability. The proposed suspension system consists of a system controller that determine the desired damping force using a PID controller tuned using PSO, and a continuous state damper controller that estimate the command voltage that is required to track the desired damping force. The PSO technique is applied to solve the nonlinear optimization problem to find the PID controller gains by identifying the optimal problem solution through cooperation and competition among the individuals of a swarm.

The paper will present the design of shift fork for automotive manual gearbox dedicated for the manufacturing with powder metal technology. Based on limitations and requirements of new production technology of shifting sleeve, the new design of shifting sleeve and shifting fork are created. The prototypes of shift fork and sleeve were built, but for cost reasons, were manufactured from steel. The functionality of several forks with different tolerances was tested. Prototypes were put through functional and durability tests on testing bench in real automotive gearbox. The tests were accomplished on the inertia test stand. Drawings and CAD models of tested prototypes, custom tools and designed shift forks are described in detail in this article.

N-butanol and isobutanol are alcohols that can be produced from biomass by fermentation and are possibly more compatible with existing engines than ethanol. This work reports on the effects of these two isomers on exhaust emissions of an unmodified direct injection spark ignition (DISI) engine. A Ford Focus car with a 1.0-liter Euro 6 Ecoboost DISI engine has been tested on a chassis dynamometer using WLTP and Artemis driving cycles, and on the road on a one-hour test loop containing urban, rural and motorway driving. Two isomers of butanol, 1-butanol and 2-methyl-propanol, were each blended with gasoline at 25% volume. Non-oxygenated gasoline and 15% ethanol in gasoline (E15) were used as reference fuels. The vehicle performed well in terms of cold start, drivability, general performance, and off-cycle particle emissions, staying within several mg of particle mass and about 2×1012 particles (per PMP procedure) per km during laboratory tests.

The physical 1-D model of a radial turbine consists of a set of gas ducts featuring total pressure and/or temperature changes and losses. Therefore, the wave propagation and filling/emptying plays a significant role if a turbine is subjected to unsteady gas flow. The results of unsteady turbine simulation using the basic modules of generalized 1-D manifold solver in GT Power are demonstrated. The turbine model calibration parameters can be identified by means of 1-D steady model used in optimization code loop. The examples of model results are compared to steady flow map predictions of turbine efficiency and engine pumping loop work. The model may be used for prediction of turbine data in out-of-design points as presented in the paper. The other important role of a model, however, is an accurate evaluation of turbine parameters from pressure and speed measurements at an engine in operation.

A previously developed CFD-based optimization tool is utilized to find optimal engine operating conditions with respect to fuel consumption and emissions. The optimization algorithm employed is based on the steepest descent method where an adaptive cost function is minimized along each line search using an effective backtracking strategy. The adaptive cost function is based on the penalty method, where the penalty coefficient is increased after every line search. The parameter space is normalized and, thus, the optimization occurs over the unit cube in higher-dimensional space. The application of this optimization tool is demonstrated for the Sulzer S20, a central-injection, non-road DI diesel engine. The optimization parameters are the start of injection of the two pulses of a split injection system, the duration of each pulse, the exhaust gas recirculation rate, the boost pressure and the compression ratio.

The aim of the current contribution is to develop a tool for the improvement of accuracy of turbocharger turbine simulation during matching of a turbocharger to an engine. The paper demonstrates the possibility of unsteady turbine simulation in pulsating flow caused by an internal combustion engine using the basic modules of generalized 1-D manifold solver with entities (pipes, channels) under centrifugal acceleration in general direction and under non-uniform angular speed, which has not yet been explored. The developed model extrapolates steady operation turbine maps by this way. It uses 1-D model parameters identified from steady flow experiments. Unlike the lumped-parameter standard models of turbocharger turbines, the model takes into account complete 1-D features of a turbine flow path including arbitrary shape of turbine impeller vanes.

The current study was focused on flow field measurements of diesel sprays. The global fuel spray characteristics, such as spray penetration, have also been measured. Particle Image Velocimetry (PIV) was utilized for flow field measurements and the global spray characteristics were recorded with high-speed back light photographing. The flow field was scanned to get an idea of the compatibility of PIV technique applied to dense and high velocity sprays. It is well proven that the PIV technique can be utilized at areas of low number density of droplets, but the center of the spray is way beyond the ideal PIV measurement conditions. The depth at which accurate flow field information can be gathered was paid attention to.

The development of new high power diesel engines is continually going for increased mean effective pressures and consequently increased thermal loads on combustion chamber walls close to the limits of endurance. Therefore accurate CFD simulation of conjugate heat transfer on the walls becomes a very important part of the development. In this study the heat transfer and temperature on piston surface was studied using conjugate heat transfer model along with a variety of near wall treatments for turbulence. New wall functions that account for variable density were implemented and tested against standard wall functions and against the hybrid near wall treatment readily available in a CFD software Star-CD.

The paper deals with dynamics of hybrid propulsion system with electric power divider. The physical laboratory model was chosen as example. Mathematical model for transient phenomena during accelerating period of the hybrid vehicle using electric power divider was developed. The accelerating period is divided into three parts. During the first part from stand condition to very low car velocity is the vehicle driven only by the energy from battery. During the second part the battery is totally off and only the combustion engine drives the vehicle. The engine is controlled by ASR system not to bring the vehicle into slipping by getting over the adhesion. In the third part of accelerating period the combustion engine power and revolutions are controlled to get minimum fuel consumption. The simulation can help to find good strategy of the powertrain control.

The new simulation tool consists of an iterative loop of a 3-D code in parallel to a 1-D code that is employed to simulate transient engine cycles. The 1-D code yields the basic pattern of initial and boundary conditions and the 3-D simulations at several typical engine operating points are used to crosscheck the performance as well as aid in the model calibration. A flexible regression model of the fuel burn rate and the associated ROHR has been developed in conjunction with the 3-D simulations using a combination of three added Vibe functions. The emissions at the end of the expansion stroke are also predicted. The parameters of the Vibe functions and emissions are found via nonlinear regression based on state parameters such as engine speed, relative A/F ratio, EGR/rest gas contents, injection timings, etc. Additional 3-D simulations that are made at specific engine operating points complement this compact burn rate parameter library.

The paper deals with investigation of flow characteristics of turbocharger turbine under real operating conditions on engine by means of combination of experimental data and advanced 1-D code for combustion engine simulation. Coupling simulations tools with the results of measurements provides the engineers with data which are difficult or impossible to measure. For instance by means of a three pressure analysis (TPA) applicable on engine cylinder the engineers can obtain burn rate, valve flow and residual gas compound from measured pressure traces in cylinder and at inlet and outlet ports. A method for turbocharger turbine on engine identification similar in principle to the three pressure analysis has been applied on radial turbine with variable geometry. A new computational module has been developed to allow identification of instantaneous flow and efficiency characteristics of the turbine.

This study is presenting a comparative spray study of modern large bore medium speed diesel engine common rail injectors. One subject of paper is to focus on nozzles with same nominal flow rate, but different machining. The other subject is penetration velocity measurements, which have a new approach when trying to understand the early phase of transient spray. A new method to use velocimetry for spray tip penetration measurements is here introduced. The length where spray penetration velocity is changed is found. This length seems to have clear connection to volume fraction of droplets at gas. These measurements also give a tool to divide the development of spray into acceleration region and deceleration region, which is one approach to spray penetration. The measurements were performed with backlight imaging in pressurized injection test rig at non-evaporative conditions. Gas density and injection pressure were matched to normal diesel engine operational conditions.

The design and testing of the valve train for a new two-stroke diesel engine concept [1,2] is presented. The gas exchange of this process requires extremely fast-acting inlet valves, which constituted a very demanding designing task. A simulation model of the prototype valve train was constructed with commercially available software. The simulation program served as the main tool for optimizing the dynamic behavior of the valve train. The prototype valve train was built according to the simulations and valve acceleration measurements were performed in order to validate the simulation results. The simulations and measurements are presented in detail in this paper.

The discrete droplet model is widely used to describe two-phase flows such as high-velocity dense sprays. The interaction between the liquid and the gas phase is modeled via appropriate source terms in the gas phase equations. This approach can lead to a strong dependence of the liquid-gas coupling on the spatial resolution of the gas phase. The liquid-gas coupling requires the computation of source terms using the gas phase properties, and, subsequently, these sources are then distributed onto the gas phase mesh. In this study, a Lagrange polynomial interpolation method has been developed to evaluate the source terms and also to distribute these source terms onto the gas mesh. The focus of this investigation has been on the momentum exchange between the two phases. The Lagrange polynomial interpolation and source term distribution methods are evaluated for non-evaporating sprays using KIVA3 as a modeling platform.

A novel two-stroke engine concept is introduced. The cylinder scavenging takes place during the upward motion of the piston. The gas exchange valves are similar to typical four-stroke valves, but the intake valves are smaller and lighter. The scavenging air pressure is remarkably higher than in present-day engines. The high scavenging air pressure is produced by an external compressor. The two-stroke operation is achieved without the drawbacks of port scavenged engines. Moreover, the combustion circumstances, charge pressure and temperature and internal exhaust gas re-circulation (EGR) can be controlled by using valve timings. There is good potential for a substantial reduction in NOx emissions through the use of adjustable compression pressure and temperature and by using the adjustable amount of exhaust gas re-circulation.

This study presents diesel spray breakup regimes and the wave model basic theory from literature. The RD wave model and the KH-RT wave model are explained. The implementation of the KH-RT wave model in a commercial CFD code is briefly presented. This study relies on experimental data from non-evaporating sprays that have earlier been measured at Helsinki University of Technology. The simulated fuel spray in a medium-speed diesel engine had a satisfactory match with the experimental data. The KH-RT wave model resulted in a much faster drop breakup than with the RD wave model. This resulted in a thin spray core with the KH-RT model. The fuel viscosity effect on drop sizes was well predicted by the KH-RT wave model.

New tire model is under development in European Commission research project called VERT (Vehicle Road Tire Interaction, BRPR-CT97-0461). The objective of the project is to create a physical model for tire/surface contact simulation. One of the subtasks has been to develop a method for snow surface characterization. The aim is simulate winter tire on snow surface with FEM software. This kind of simulation has been earlier done with snow model parameters from laboratory experiments. A snow shear box device has been developed in Helsinki University of Technology to measure mechanical properties of snow in field conditions. Both shear and compression properties can be measured with the device. With the device, a large number of snow measurements have been done at the same time with VERT winter tire testing in Nokian Tyres'' test track in Ivalo Finland. Measurement data have been postprocessed afterwards and parameters for material models have been evaluated.

New technology for the manufacturing of copper/brass heat exchangers has been developed and the first automotive radiators are already in operation in vehicles. This new technology is called CuproBraze®. One of the essential questions raised is the external corrosion resistance with reference to the present soldered copper/brass radiators and to the brazed aluminium radiators. Based on the results from electrochemical measurements and from four different types of accelerated corrosion tests, the external corrosion resistance of the CuproBraze® radiators is clearly better than that of the soldered copper/brass radiators and competitive with the brazed aluminum radiators, especially as regards marine atmosphere. Due to the relatively high strength of the CuproBraze® heat exchangers, down gauging of fins and tubes in some applications is attractive. High performance coatings can ensure long lifetime from corrosion point of view, even for thin gauge heat exchangers.

Three-dimensional diesel engine combustion simulations with single-step chemistry have been compared with two-step and three-step chemistry by means of the Laminar and Turbulent Characteristic Time Combustion model using the Star-CD program. The second reaction describes the oxidation of CO and the third reaction describes the combustion of H2. The comparisons have been performed for two heavy-duty diesel engines. The two-step chemistry was investigated for a purely kinetically controlled, for a mixing limited and for a combination of kinetically and mixing limited oxidation. For the latter case, two different descriptions of the laminar reaction rates were also tested. The best agreement with the experimental cylinder pressure has been achieved with the three-step mechanism but the differences with respect to the two-step and single-step reactions were small.

A modified version of the Laminar and Turbulent Characteristic Time combustion model and the Hiroyasu-Magnussen soot model have been implemented in the flow solver Star-CD. Combustion simulations of three DI diesel engines, utilizing the standard k-ε turbulence model and a modified version of the RNG k-ε turbulence model, have been performed and evaluated with respect to combustion performance and emissions. Adjustments of the turbulent characteristic combustion time coefficient, which were necessary to match the experimental cylinder peak pressures of the different engines, have been justified in terms of non-equilibrium turbulence considerations. The results confirm the existence of a correlation between the integral length scale and the turbulent time scale. This correlation can be used to predict the combustion time scale in different engines.