Search Results

The BMW Group has introduced electric cars to the market with the MINI E already in 2009. The next step will be the launch of the BMW ActiveE in 2011, followed by the revolutionary Mega City Vehicle in 2013. The presentation will explain the BMW Group strategy for implementing sustainable mobility. A focus will be emobility, the use of carbon fiber and the holistic sustainability approach of BMW Group?s project i. Reference will be made to the research results of the MINI E projects in the US and in Europe. Presenter Andreas Klugescheid, BMW AG

Swirling flows are very dominant in applied technical problems, especially in IC engines, and their prediction requires rather sophisticated modeling. An adaptive low-pass filtering procedure for the modeled turbulent length and time scales is derived and applied to Menter' original k - ω SST turbulence model. The modeled length and time scales are compared to what can potentially be resolved by the computational grid and time step. If the modeled scales are larger than the resolvable scales, the resolvable scales will replace the modeled scales in the formulation of the eddy viscosity; therefore, the filtering technique helps the turbulence model to adapt in accordance with the mesh resolution and the scales to capture.

In the next years, the upcoming emission legislations are expected to introduce further restrictions on the admittable level of pollutants from vehicles measured on homologation cycles and real drive tests. In this context, the strict control of pollutant emissions at the cold start will become a crucial point to comply with the new regulation standards. This will necessarily require the implementation of novel strategies to speed-up the light-off of the reactions occurring in the after-treatment system, since the cold start conditions are the most critical one for cumulative emissions. Among the different possible technological solutions, this paper focuses on the evaluation of the potential of a burner system, which is activated before the engine start. The hypothetical burner exploits the lean combustion of an air-gasoline mixture to generate a high temperature gas stream which is directed to the catalyst section promoting a fast heating of the substrate.

Highly automated driving (HAD) is under rapid development and will be available for customers within the next years. However the evidence that HAD is at least as safe as human driving has still not been produced. The challenge is to drive hundreds of millions of test kilometers without incidents to show that statistically HAD is significantly safer. One approach is to let a HAD function run in parallel with human drivers in customer cars to utilize a fraction of the billions of kilometers driven every year. To guarantee safety, the function under test (FUT) has access to sensors but its output is not executed, which results in an open loop problem. To overcome this shortcoming, the proposed method consists of four steps to close the loop for the FUT. First, sensor data from real driving scenarios is fused in a world model and enhanced by incorporating future time steps into original measurements.

The flow field resulting from injecting a gas jet into a crossflow confined in a narrow square duct has been studied under steady regime using schlieren imaging and laser Doppler velocimetry (LDV). This transparent duct is intended to simulate the intake port of an internal combustion engine fueled by gaseous mixture, and the jet is issued from a round nozzle. The schlieren images show that the relative small size of the duct would confine the development of the transverse jet, and the interaction among jet and sidewalls strongly influences the mixing process between jet and crossflow. The mean velocity and turbulence fields have been studied in detail through LDV measurements, at both center plane and several cross sections. The well-known flow feature formed by a counter rotating vortex pair (CVP) has been observed, which starts to appear at the jet exit section and persists far downstream contributing to enhancing mixing process.

Innovative electric systems demand a new approach for the distribution of electric energy in passenger cars. This paper describes a very promising solution-the dual voltage power network with an upper voltage level of 42V, and the considerations which led to the selection of this voltage level. Owing to the significant impact on the industry, a common standard is required. Depending on their profile, OEMs will select their own strategies for implementation, either as a base for innovation or to enhance overall system efficiency. This will lead to different approaches and timeframes.

Reduction of pollutants and greenhouse gas emissions is one of the main objectives of car manufacturers and innovative solutions have to be considered to achieve this goal. Electric vehicles, and in particular Fuel Cell Electric Vehicles, appear to be a promising alternative. Renault is therefore investigating the technical and economic viability of a Fuel Cell Electric Vehicle (FCEV). A basic question of this study is the choice of the fuel that will be used for this kind of vehicle. Liquid fuels such as gasoline, diesel, naphtha, and gas-to-liquid can be a bridge for the introduction of fuel cell technologies while hydrogen infrastructure and storage are investigated. Therefore, multi-fuel Fuel Processor Systems that can convert liquid fuels to hydrogen while meeting automotive constraints are desired. Renault and Nuvera have joined forces to tackle this issue in a 3-year program where the objective is to develop and to integrate a Fuel Processor System (FPS) on a vehicle.

The optimization of the vaporization and mixture formation process is of great importance for the development of modern gasoline direct injection (GDI) engines, because it influences the subsequent processes of the ignition, combustion and pollutant formation significantly. In consequence, the subject of this work was the development of a measurement technique based on the laser induced exciplex fluorescence (LIF), which allows the two dimensional visualization and quantification of the in-cylinder air/fuel ratio. A tracer concept consisting of benzene and triethylamine dissolved in a non-fluorescent base fuel has been used. The calibration of the equivalence ratio proportional LIF-signal was performed directly inside the engine, at a well known mixture composition, immediately before the direct injection measurements were started.

Since its creation in 1996, Euroncap evaluated more than 80 cars, ranging from small and city cars, to larger vehicles such as executive cars and people carriers (MPVs). The testing protocol comprises 3 types of tests: a frontal offset test against a deformable barrier, a 90° lateral impact with a moving deformable barrier, and - since March 2000 - a pole side impact. In addition a set of subsystem tests with impactors on the bonnet and the front face of the car are conducted to assess the pedestrian protection. The aim of this paper is to review the testing and assessment protocols and to compare them with those used in other NCAP systems in the USA, Australia, Japan and Europe. In particular, important Euroncap issues such as the stiffness of heavier vehicles that could be increased in the future, and the nature and weight of the modifiers are discussed. Ways to improve the system are suggested in relation with real-world accident data.

An experimental campaign is presented aiming at the characterization of thermal dissipation of batteries to be used on board of small satellites. A suitably designed device allows to manage automatically the orbital cycling simulation between battery cell charge and discharge. The cell thermal performance is characterized in various combinations of temperature, discharge current and Depth of Discharge. The gathered data are used for providing guidelines in the design of a family of Italian Small Satellites.

This paper presents the following VAN concept led by a vehicle analysis: electrical architecture must not be basically changed in order to be cost effective; efficiency, interoperability and safety aspects must be rigorously respected to avoid lack of quality. As a consequence VAN solutions meet the requirement set concerning wiring, transceivers, protocol controllers and software services. Each of these solutions is optimized to assure safety and easy use. VAN transceivers support multiplexed applications - even high speed application - with conventional wiring. VAN controllers offer a large diversity of services, so allow the minimization of network load, of CPU load, with a high Real Time efficiency. Moreover their structure is very open to diagnosis requirements. VAN softwares provide simple, reliable, reusable mechanisms of sharing, exchange and synchronization. Such mechanisms minimize cost development and guarantee safety proofs in the liability context.

The paper is focused on both the subjective and the objective ride comfort evaluation of farm tractors. The experimental measurement of the relevant accelerations occurring at the tractor body, at the cabin and at the seat was performed on a number of different farm tractors. A subjective rating of the ride comfort level was performed by considering five different drivers. The comfort index was computed according with ISO 2631 and other standards. The acceleration of the seated subject was computed by means of a proper mechanical model of a farm tractor and derived at different positions on the subject body. It turned out that the acceleration of the lower torso was particularly relevant for establishing a matching between the subjective perception and the objective measurement and computation. A number of indices have been derived from the measured data which are able to correlate the subjective driver feeling with the measured accelerations.

This work focuses on the analysis of the vertical dynamics of an agricultural tractor, investigating the influence of suspensions' parameters on riding comfort and contact forces. The use of lugged tires coupled with the operation over banked, irregular and deformable tracks, determines significant levels of vertical acceleration over several components of the tractor. These operating conditions have a direct effect on the driver, whose alertness and efficiency are undermined by the exposure to high levels of acceleration for a long time. Secondly, variations of the normal and traction forces provided by the tires affect the quality of tillage and other operations. The paper presents a multi-body vehicle model of a tractor interfaced with a tire-soil contact model allowing to take into account soil's deformation and tread pattern design.

To reduce greenhouse gas emissions such as CO2, automakers are actively pursuing alternative propulsion systems. Improvements to current engine technology are being investigated along with new power plant technologies. Fuel Cell Vehicles offer an exciting option by producing electric power through a reaction that combines hydrogen and oxygen to make water. However, hydrogen storage onboard vehicles and construction of an expensive hydrogen distribution and fueling infrastructure remain as challenges today. In addition, greenhouse gas emissions from the production of hydrogen must be considered since most hydrogen is currently produced from non-renewable sources. While these issues are being worked on, Renault has chosen to pursue a fuel cell vehicle with a fuel processor that converts gasoline and other liquid fuels to hydrogen onboard the vehicle.

The use of micro controllers in automotive systems renders the coordination of about 150 actors (70 electric motors, 15 magnetic valves and 50 relays). The resulting complexity of those systems as well as the requested zero defects demands time consuming testing. This work describes a method of performing test-scenarios, starting from a zero defect running specification, modeled by finite state machines. The test-scenarios are intended to determine whether a given system meets all specification requirements. First, a kind of structured modelling reactive automotive systems is deduced. Next, some important test selection methods, developed for the case the specification is given in the form of a finite state machine, are considered. Finally, a procedure and method for performing minimized complete test-scenarios for automotive systems are presented.

The production of the BMW ALPINA B12 5.7 with Switch-Tronic transmission provides the markets of Europe and Japan with an exclusive, luxury-orientated, high performance limited series limousine. This is the first vehicle worldwide to be fitted with the progressive exhaust gas aftertreatment technology known as the Electrically Heated Catalyst (EHC), in which the effectiveness of the power utilized is increased significantly by an alternating heating process for both catalytic converters. Only since this achievement has the implementation of the EHC been viable without extensive modification to the battery and alternator. With this exhaust gas aftertreatment concept, the emissions of this high performance vehicle will fall to less than half the maximum permissible for compliance with 1996 emission standards.

There is a common understanding that hydrogen has a great potential to be the fuel of the future. In addition to the challenge of developing appropriate hydrogen propulsion systems the development of hydrogen storage systems is the second big issue. Due to its high potential in cost and weight and specific storage capacity, the BMW Group is focusing on the development of liquid hydrogen storage systems. In the next hydrogen 7-Series the BMW Group is about to make for the first time the step from demonstration fleets to cars used by external users with a liquid hydrogen storage system. To realize this significant goal, special focus has to be put on high safety standards so that hydrogen can be considered as safe as common types of fuel, and on the every day reliability of the storage system. Moreover, the development of strong partnerships with suppliers is a key factor to realize the design and identify appropriate manufacturing processes.

Multi-purpose agricultural tractors are vehicles that are usually used in rough paths and on off-road situations characterized by strong slope variations. The main feature of this kind of vehicles is the stability in working conditions to avoid overturning while it is on duty. This characteristic is given by the interaction between the suspension system and the vehicle frame. Due to the limited size of this kind of vehicle, the stability feature could be given by chassis deformation or using a two-piece frame connected by a spherical joint. This paper presents the validation of a numerical lumped-parameters model able to reproduce the vertical dynamics of a multi-purpose tractor featured by a yielding chassis. The unknown model parameters have been estimated firstly with static tests to study the vertical tire and suspension stiffnesses. The dynamic tests using a four-post-test rig have been performed to tune the unknown dynamic parameters.

Due to their high energy density, power density, and durability, lithium-ion (Li-ion) batteries are rapidly becoming the most popular energy storage method for electric vehicles. Difficulty arises in accurately estimating the amount of left capacity in the battery during operation time, commonly known as battery state of charge (SOC). This paper presents a comparative study between six different Equivalent Circuit Li-ion battery models and two different state of charge (SOC) estimation strategies. The Battery models cover the state-of-the-art of Equivalent Circuit models discussed in literature. The Li-ion battery SOC is estimated using non-linear estimation strategies i.e. Extended Kalman filter (EKF) and the Smooth Variable Structure Filter (SVSF). The models and the state of charge estimation strategies are compared against simulation data obtained from AVL CRUISE software.

In this work, the possibility to perform a cold-flow simulation as a way to improve the accuracy of the starting conditions for a combustion simulation is examined. Specifically, a dual-fuel marine engine running on methanol/diesel and natural gas/diesel fueling conditions is investigated. Dual-fuel engines can provide a short-term solution to cope with the more stringent emission legislations in the maritime sector. Both natural gas and methanol appear to be interesting alternative fuels that can be used as main fuel in these dual-fuel engines. Nevertheless, it is observed that combustion problems occur at part load using these alternative fuels. Therefore, different methods to increase the combustion efficiency at part load are investigated. Numerical simulations prove to be very suitable hereto, as they are an efficient way to study the effect of different parameters on the combustion characteristics.