Search Results

The effect of hydroforming on the mechanical properties and dynamic crush behaviors of tapered aluminum 6063-T4 tubes with octagonal cross section are investigated by experiments. First, the thickness profile of the hydroformed tube is measured by non-destructive examination technique using ultrasonic thickness gauge. The effect of hydroforming on the mechanical properties of the tube is investigated by quasi-static tensile tests of specimens prepared from different regions of the tube based on the thickness profile. The effect of hydroforming on the dynamic crush behaviors of the tube is investigated by axial crush tests under dynamic loads. Specimens and tubes are tested in two different heat treatment conditions: hydroformed-T4 (as-received) and T6. The results of the quasi-static tensile tests for the specimens in hydroformed-T4 condition show different amounts of work hardening depending on the regions, which the specimens are prepared from.

The responses of the THOR and the Hybrid-III ATDs to head and neck loading due to a deploying air bag were investigated. Matched pair tests were conducted to compare the responses of the two ATDs under similar loading conditions. The two 50th percentile male ATDs, in the driver as well as the passenger positions, were placed close to the air bag systems, in order to enhance the interaction between the deploying air bag and the chin-neck-jaw regions of the ATDs. Although both ATDs nominally meet the same calibration corridors, they differ significantly in their kinematic and dynamic responses to interaction with a deploying air bag. The difference between the structural designs of the Hybrid-III's and the THOR's neck appears to result in significant differences in the manner in which the loads applied on the head are resisted.

As the volume and complexity of electronics increases in automobiles, so does the complexity of the electromagnetic relationship between systems. The reliability and functionality of electronic systems in automobiles can be affected by noise sources such as direct current (DC) motors. A typical automobile has 25 to 100+ DC motors performing different tasks. This paper investigates the noise environment due to DC motors found in automobiles and the requirements that automobile manufacturers impose to suppress RF electromagnetic noise and conducted transients.

The new generation of drive-by-wire systems currently under development has demanding requirements on the electronic architecture. Functions such as brake-by-wire or steer-by-wire require continued operation even in the presence of component failures. The electronic architecture must therefore provide fault-tolerance and real-time response. This in turn requires the operating system and the communication layer to be predictable, dependable and composable. It is well known that this properties are best supported by a time-triggered approach. A consortium consisting of German and French car manufacturers and suppliers, which aims at becoming a working group within the OSEK/VDX initiative, the OSEKtime consortium, is currently defining a specification for a time-triggered operating system and a fault-tolerant communication layer.1 The operating system and the communication layer are based on applicable interfaces of the OSEK/VDX standard.

Future emission regulations and customer needs require revolutionary new approaches to engine management systems. In the EC part-funded AENEAS program the partners Ricardo, Kistler and DaimlerChrysler formed a consortium to investigate the application of a new combustion pressure sensor concept and innovative algorithms for engine management systems. This paper describes the general scope and the basic concepts of the system.

This paper describes additional and more recent results from the DaimlerChrysler study of HANS that includes a sensitivity analysis of HANS performance to variations in crash dummy neck length and other impact test conditions. The objective of the tests was to determine the robustness of the HANS concept in a variety of conditions that might occur in actual use. The results show that the variations in test parameters do effect injury measures from the crash dummy, but HANS provides substantial reductions in injury potential in all cases compared to not using HANS. Also, no injuries were indicated with HANS.

A comparative investigation of airbag and HANS driver safety systems was carried out (HANS, is a Registered Trademark in the U.S.A.). With both systems, head and neck loads were reduced from potentially fatal values to values well below the injury threshold. Both systems performed similarly in reducing the potential for driver injury. For this reason and given the high costs of development and testing, there is no justification for further development of airbags for racing.

An early development vehicle experienced an unusually high rate of windshield breakage. Most breaks were identified as due to impact, but the severity of impact was low. It was reasoned that the windshield should possess a greater level of robustness to impact. Many theories were put forth to explain the breakage data. It was universally agreed that the unusual breakage rate could be due to only one condition, but its source was indefinite. The condition present must be tensile stress. One of three situations were considered regarding its source: 1) the tensile stress was present in the glass after manufacture due to improper annealing; 2) the installation of the windshield into the vehicle body put the glass into stress; 3) some combination of the other two sources. A gray-field polariscope was used to measure the stresses of the windshield from both the manufacturing process as well as the installation in the vehicle.

Power train noise reaches the interior through structureborne paths and through airborne transmission of engine casing noise. To determine transfer functions from vibration to interior noise a shaker was attached at the engine attachment points, with the engine removed. A simple engine noise simulator, with loudspeaker cones on its faces, was placed in the engine compartment to measure airborne transfer functions to interior noise. Empirical noise estimates, based on the incoherent sum of contributions for individual source terms times the appropriate transfer function, compared remarkably well with measured levels obtained from dynomometer tests. Airborne transmission dominates above 1.5kHz. At lower frequencies engine casing radiation and vibration contributions are comparable.

A simple spring-mass model of the impact response of the side impact dummy (SID) is established. The spring and mass constants of the model are established through system identification methodology based on data from impact tests. The tests are performed in laboratory with hydraulically driven impactors impacting the chest and pelvis of the SID. The input data to the model consist of measured contact force or impactor velocity time histories, and the output data are accelerations on the rib, spine, and pelvis of the SID. The established model appears to predict the test results with reasonable accuracy. The main purpose of this study, however, is to use this simple model to carry out parametric studies of the response of the dummy with changing impact parameters, the result of which would be useful in understanding vehicle crash tests using the SID.

Reductions of hardware costs as well as implementations of new innovative functions are the main drivers of today's automotive electronics. Indeed more and more resources are spent on adapting existing solutions to different environments. At the same time, due to the increasing number of networked components, a level of complexity has been reached which is difficult to handle using traditional development processes. The automotive industry addresses this problem through a paradigm shift from a hardware-, component-driven to a requirement- and function-driven development process, and a stringent standardization of infrastructure elements. One central standardization initiative is the AUTomotive Open System ARchitecture (AUTOSAR). AUTOSAR was founded in 2003 by major OEMs and Tier1 suppliers and now includes a large number of automotive, electronics, semiconductor, hard- and software companies.