Search Results

Intense competition in the automotive industry requires continuous reduction in innovation cycle time, even as corporations are downsizing and system complexity is increasing. Subsequently, the application of recently introduced Rapid Algorithm Development (RAD) tools has facilitated significant advances in the development of embedded control systems. The RAD steps include system modeling, control algorithm design, simulation analysis, automated calibration design, and vehicle implementation through automatic code generation. The application of RAD tools and the associated benefits are described, specifically in the context of Engine Management Systems (EMS). Such benefits include significant reductions in development cycle time, open architecture, automated calibration, and information reuse.

This paper presents a brake pressure estimation algorithm for Delphi Traction Control Systems (TCS). A control oriented lumped parameter model of a brake control system is developed using Matlab/Simulink. The model is derived based on a typical brake system and is generic to other types of brake control hardware systems. For application purposes, the model is simplified to capture the dominant dynamic brake pressure response. Vehicle experimental data collected under various scenarios are used to validate the algorithm. Simulation results show that the algorithm gives accurate pressure estimation. In addition, the calibration procedure is greatly simplified

This paper presents a theoretical and experimental study of a cylinder deactivation valvetrain system for the integration into an Engine Management System (EMS). A control-oriented lumped parameter model of the deactivation valvetrain system is developed and implemented using Matlab/Simulink, and validated by experimental data. Through simulation and experimental data analysis, the effect of operating conditions on the dynamic response is captured and characterized, over a wide range of operating conditions. The algorithm provides a basis for the calibration of the deactivation hardware. The generic characterization of the dynamic response can simplify the calibration parameters for the implementation in engine management systems.

This paper describes an environment for the development of production Engine Management Systems (EMS). This includes a formal framework and modeling methodology. The environment is based on using Simulink/Stateflow for developing a control system executable specification and a plant model. This allows for simulations of the system to be performed at the engineer's desk, which is identical performance with production software. We provide the details for incorporating production legacy code into the Simulink/Stateflow control system. The system includes a multi-rate, and event driven operating system. This system is developed to facilitate new algorithm development and automated software testing. Based on Simulink/Stateflow this specification will be suitable for use with commercial automatic code generation tools.

This paper describes the verification and comparison of position control algorithms for a continuously-variable cam phaser. Robust Engineering techniques are used. Two non-linear PID control algorithms are designed to control cam phaser position. The first algorithm is a more complex control strategy while the second is a thrifted approach that seeks to reduce throughput requirements. An L18 orthogonal array is established with noise factors that affect the quality of cam phaser control. Using the orthogonal array, the number of experiment test points required to characterize the control algorithm response is reduced from 8,748 to thirty-six. The test points of the orthogonal array are investigated experimentally on a motored engine outfitted with cam phaser hardware. The desired and actual cam position data are compared and analyzed for all points in the orthogonal array.

Recent advances in dependable embedded system technology, as well as continuing demand for improved handling and passive and active safety improvements, have led vehicle manufacturers and suppliers to actively pursue development programs in computer-controlled, by-wire subsystems. These subsystems include steer-by-wire and brake-by-wire, and are composed of mechanically de-coupled sets of actuators and controllers connected through multiplexed, in-vehicle computer networks; there is no mechanical link to the driver. This paper addresses fundamental benefits and issues of steer-by-wire, especially those related to automated vehicle control and steering feel quality as perceived by the driver.

This paper describes the development and implementation of an Engine Drag Control algorithm to improve vehicle stability performance. Engine drag can occur on low and high coefficient surfaces when the driver suddenly releases the throttle. If the engine drag force becomes larger than the frictional force between the tire and the road, the tires will break loose from the surface and slip. This could induce vehicle instability especially with rear drive vehicles on low-coefficient surfaces. The EDC algorithm has been developed to provide accurate control of the wheels. EDC will help reduce the yaw rate of the vehicle and thus achieve greater vehicle stability. The paper also presents methods used to test the robustness of such a system. The purpose of the testing was to ensure that there would be no false activations of EDC under normal driving conditions and also to ensure that, when the system is active, it is mostly transparent to the driver.

This paper presents the objectives and preliminary results of the BRAKE project - a joint effort of Delphi Automotive Systems, Infineon Technologies, Volvo Car Corporation and WindRiver. The objective of this project is to use microelectronics technologies to design a distributed Brake-by-Wire system including: A distributed fault tolerant system for enhanced safety An extension of the OSEK based operating system for a distributed time triggered architecture An open interface between vehicle control, and brake system control The results comprise the requirements, interface specification (see [1]), a full simulation model, a hardware-in-the-loop bench, and a demonstration vehicle. The application has been developed using advanced automatic code generation for Infineon's TriCore based automotive microcontrollers.

Today automotive system suppliers develop more-or-less independent systems, such as brake, power steering and suspension systems. In the future, car manufacturers like Volvo will build up vehicle control systems combining their own algorithms with algorithms provided by automotive system suppliers. Standardization of interfaces to actuators, sensors and functions is an important enabler for this vision and will have major consequences for functionality, prices and lead times, and thus affects both vehicle manufacturers and automotive suppliers. The investigation of the level of appropriate interfaces, as part of the European BRAKE project, is described here. Potential problems and consequences are discussed from both a technical and a business perspective. This paper provides a background on BRAKE and on the functional decomposition upon which the interface definitions are based. Finally, the interface definitions for brake system functionality are given.

Delphi is developing a new combustion technology called Gasoline Direct-injection Compression Ignition (GDCI), which has shown promise for substantially improving fuel economy. This new technology is able to reuse some of the controls common to traditional spark ignition (SI) engines; however, it also requires several new sensors and actuators, some of which are not common to traditional SI engines. Since this is new technology development, the required hardware set has continued to evolve over the course of the project. In order to support this development work, a highly capable and flexible electronic control system is necessary. Integrating all of the necessary functions into a single controller, or two, would require significant up-front controller hardware development, and would limit the adaptability of the electronic controls to the evolving requirements for GDCI.

This paper investigates a method for improving vehicle stability by incorporating feedback from a yaw rate sensor into an electric power steering system. Presently, vehicle stability enhancement techniques are an extension of antilock braking systems in aiding the driver during vehicle maneuvers. One of the contributors to loss of vehicle control is the reduction in tactile feedback from the steering handwheel when driving on wet or icy pavement. This paper presents research indicating that the use yaw rate feedback improves vehicle stability by increasing the amount of tactile feedback when driving under adverse road conditions.

An algorithm for estimation of vehicle yaw rate and side slip angle using steering wheel angle, wheel speed, and lateral acceleration sensors is proposed. It is intended for application in vehicle stability enhancement systems, which use controlled brakes or steering. The algorithm first generates two initial estimates of yaw rate from wheel speeds and from lateral acceleration. A new estimate is subsequently calculated as a weighted average of the two initial ones, with the weights proportional to confidence levels in each estimate. This preliminary estimate is fed into a closed loop nonlinear observer, which generates the final estimate of yaw rate along with estimates of lateral velocity and side slip angle. Parameters of the observer depend on the estimated surface coefficient of adhesion, thus providing adaptation to changes in road surface coefficient of adhesion.

A finite element model of a folded airbag with the module cover and steering wheel system was developed to estimate the injury numbers of a 5th percentile female dummy in an out-of-position (OOP) situation. The airbag model was correlated with static airbag deployments and standard force plate tests. The 5th percentile finite element dummy model developed by First Technology Safety Systems (FTSS) was used in the simulation. The following two OOP tests were simulated with the airbag model including a validated steering wheel finite element model: 1. Chest on air bag module for maximum chest interaction from pressure loading (MS6-D) and 2. Neck on air bag module for maximum neck interaction from membrane loading (MS8-D). These two simulations were then compared to the test results. Satisfactory correlation was found in both the cases.

Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.

A Barometric Pressure Estimator (BPE) algorithm was implemented in a production speed-density Engine Management System (EMS). The BPE is a model-based, easily calibrated algorithm for estimating barometric pressure using a standard set of production sensors, thereby avoiding the need for a barometric pressure sensor. An accurate barometric pressure value is necessary for a variety of engine control functions. By starting with the physics describing the flow through the induction system, an algorithm was developed which is simple to understand and implement. When used in conjunction with the Pneumatic and Thermal State Estimator (PSE and TSE) algorithms [2], the BPE requires only a single additional calibration table, generated with an automated processing routine, directly from measured engine data collected at an arbitrary elevation, in-vehicle or on a dynamometer. The algorithm has been implemented on several different engines.

In this paper we discuss in detail an algorithm that addresses cylinder-to-cylinder imbalance issues. Maintaining even equivalence-ratio (ϕ) control across all the cylinders of an engine is confounded by imbalances which include fuel-injector flow variations, fresh-air intake maldistribution and uneven distribution of Exhaust Gas Re-circulation (EGR). Moreover, in markets that are growing increasingly cost conscious, with ever tightening emissions regulations, correcting for such mismatches must not only be done, but done at little or no additional cost. To address this challenge, we developed an Individual Cylinder Fuel Control (ICFC) algorithm that estimates each cylinder's individual ϕ and then compensates to correct for any imbalance using only existing production hardware. Prior work in this area exists1,2, yet all disclosed production-intent work was performed using wide-range oxygen sensors, representing cost increases.

Both evaporative emissions and tailpipe emissions have been reduced by more than 90% from uncontrolled levels in state-of-the-art. However, now that the objective is to reach near-zero emission levels, the need for aggressive purging of the canister and fuel tank and the need for extremely precise control of engine Air/Fuel ratio (A/F) come into conflict. On-board diagnostics and the wide variation in operating conditions and fuel properties in the “real world” add to the challenge of resolving these conflicting requirements. An advanced canister purge algorithm has been developed which substantially eliminates the effect of canister purge on A/F control by estimating and compensating for the fuel and air introduced by the purge system. This paper describes the objectives and function of this algorithm and the validation of its performance.

This paper describes a semi-active damping control system that responds in real-time to road and driving conditions based on body motions as determined through ABS wheel speed sensors. The use of these existing sensors for vehicle information eliminates the need for the additional sensors (e.g. accelerometers and body-to-wheel position/velocity sensors) that are commonly part of semi-active suspension systems. This technology also allows for further cost and part count reductions through the combination of the suspension and brake controls into a single electronic control unit. This paper has been previously presented in 1998 at the SAE Controlled Suspension System Toptec.

It has been reported that lower extremity injuries represent a measurable portion of all moderate-to-severe automobile crash- related injuries. Thus, a simple tool to assist with the design of leg and foot injury countermeasures is desirable. The objective of this study is to develop a mathematical model which can predict load propagation and kinematics of the foot and leg in frontal automotive impacts. A multi-body model developed at the University of Virginia and validated for blunt impact to the whole foot has been used as basis for the current work. This model includes representations of the tibia, fibula, talus, hindfoot, midfoot and forefoot bones. Additionally, the model provides a means for tensioning the Achilles tendon. In the current study, the simulations conducted correspond to tests performed by the Transport Research Laboratory and the University of Nottingham on knee-amputated cadaver specimens.

Adaptive Cruise Control (ACC) technology is presently on the horizon as a convenience function intended to reduce driver workload. This paper presents an implementation of a brake algorithm, which extends the production cruise control feature. A brief overview of the system architecture and subsystem interfaces to the forward-obstacle detection system, throttle and engine management controls are described. Considerations of moding ACC with ABS and Traction Control are presented at the vehicle level. This development activity is presented in two major phases. Both phases of this development project utilize CAN controllers and transceivers to implement requirements for limited access highway driving. The initial phase of development requires the brake control to follow a deceleration command and operate “open-loop” to the vehicle controller. Vehicle test data capturing smooth stops on high coefficient surfaces is presented as insight to the braking performance of the vehicle.