Search Results

Swirling flows are very dominant in applied technical problems, especially in IC engines, and their prediction requires rather sophisticated modeling. An adaptive low-pass filtering procedure for the modeled turbulent length and time scales is derived and applied to Menter' original k - ω SST turbulence model. The modeled length and time scales are compared to what can potentially be resolved by the computational grid and time step. If the modeled scales are larger than the resolvable scales, the resolvable scales will replace the modeled scales in the formulation of the eddy viscosity; therefore, the filtering technique helps the turbulence model to adapt in accordance with the mesh resolution and the scales to capture.

Omnivore is a single cylinder spark ignition based research engine conceived to maximize the operating range of auto-ignition on a variety of fossil and renewable fuels. In order to maximize auto-ignition operation, the two-stroke cycle was adopted with two independent mechanisms for control. The charge trapping valve system is incorporated as a means of varying the quantity of trapped residuals whilst a variable compression ratio mechanism is included to give independent control over the end of compression temperature. The inclusion of these two technologies allows the benefits of trapped residual gas to be maximised (to minimize NOx formation) whilst permitting variation of the onset of auto-ignition. 2000rpm and idle are the main focus of concern whilst also observing the influence of injector location. This paper describes the rational behind the engine concept and presents the results achieved at the time of writing using 98ulg and E85 fuels.

This paper outlines a vision of future engine requirements and operating strategies to reduce fuel consumption and engine out emissions. It discusses in detail the valve operating strategies used to achieve throttleless spark ignition (SI) load control and two methods of controlled Auto Ignition (AI). Emission and fuel consumption speed load maps are shown and differences between SI and AI maps are discussed. Many fully variable valve-timing strategies are proposed and conclusions are reached that clearly indicate significant improvements in IC engine performance are still achievable.

The scope of the work presented in this paper was to apply the latest open source CFD achievements to design a state of the art, direct-injection (DI), heavy-duty, natural gas-fueled engine. Within this context, an initial steady-state analysis of the in-cylinder flow was performed by simulating three different intake ducts geometries, each one with seven different valve lift values, chosen according to an estabilished methodology proposed by AVL. The discharge coefficient (Cd) and the Tumble Ratio (TR) were calculated in each case, and an optimal intake ports geometry configuration was assessed in terms of a compromise between the desired intensity of tumble in the chamber and the satisfaction of an adequate value of Cd. Subsequently, full-cycle, cold-flow simulations were performed for three different engine operating points, in order to evaluate the in-cylinder development of TR and turbulent kinetic energy (TKE) under transient conditions.

The current development to set up an automatic procedure for automatic mesh generation and automatic mesh motion for internal combustion engine simulation in OpenFOAM®-2.2.x is here described. In order to automatically generate high-quality meshes of cylinder geometries, some technical issues need to be addressed: 1) automatic mesh generation should be able to control anisotropy and directionality of the grid; 2) during piston and valve motion, cells and faces must be introduced and removed without varying the overall area and volume of the cells, to avoid conservation errors. In particular, interpolation between discrete fields is frequent in computational physics: the use of adaptive and non-conformal meshes necessitates the interpolation of fields between different mesh regions. Interpolation problems also arise in areas such as model coupling, model initialization and visualisation.

In order to reduce the development time involved in optimising the combustion system and valve timing of the internal combustion engine, an electro-hydraulic valve actuation system has been developed. The effects of various combustion strategies, including asymmetrical valve events, on emissions and efficiency, together with their sensitivity to EGR and AFR were investigated. In addition, the influence of the cylinder head design on in-cylinder charge motion and combustion was investigated by correlating airflow, tumble and swirl data to the heat release data obtained during dynamometer testing.

The paper focuses on the development of a mesh moving method based on non-conformal topologically changing grids applied to the simulation of IC engines, where the prescribed motion of piston and valves is accomplished by rigidly translating the sub-domain representing the moving component. With respect to authors previous work, a more robust and efficient algorithm to handle the connectivity of non-conformal interfaces and a mesh-motion solver supporting multiple layer addition/removal of cells, to decouple the time-step constraints of the mesh motion and of the fluid dynamics, has been implemented as a C++ library to extend the already existing classes for dynamic mesh handling of the finite-volume, open-source CFD code OpenFOAM®. Other new features include automatic decomposition of large multiple region domains to preserve processors load balance with topological changes for parallel computations and additional tools for automatic preprocessing and case setup.