Search Results

The use of catalyzed diesel particulate filter (CDPF) systems in light duty diesel (LDD) vehicles is becoming increasingly common. The primary functions of the system are to remove carbon monoxide (CO) and hydrocarbons (HC) from the vehicle exhaust stream, while simultaneously reducing the level of particulate matter (PM) emissions to ambient background levels. These systems can comprise either a separate diesel oxidation catalyst (DOC) and a downstream CDPF, or a single unit CDPF with the DOC functions incorporated within the CDPF. The single CDPF unit provides higher regeneration efficiency as it is located nearer to the engine and also cost benefits, as only a single unit is required compared to the alternative separate DOC and CDPF arrangement. A model describing the performance of the single unit CDPF for emissions control has been developed, with particular emphasis on achieving predictions of the CO and HC emissions over transient vehicle drive cycles.

Fatty Acid Methyl Ester (FAME) products derived from vegetable oils and animal fats are now widely used in European diesel fuels and their use will increase in order to meet mandated targets for the use of renewable products in road fuels. As more FAME enters the diesel pool, understanding the impact of higher FAME levels on the performance and emissions of modern light-duty diesel vehicles is increasingly important. Of special significance to Well-to-Wheels (WTW) calculations is the potential impact that higher FAME levels may have on the vehicle's volumetric fuel consumption. The primary objective of this study was to generate statistically robust fuel consumption data on three light-duty diesel vehicles complying with Euro 4 emissions regulations. These vehicles were evaluated on a chassis dynamometer using four fuels: a hydrocarbon-only diesel fuel and three FAME/diesel fuel blends containing up to 50% v/v FAME. One FAME type, a Rapeseed Methyl Ester (RME), was used throughout.

Gasoline direct injection (GDI) engines have become very attractive in transportation due to several benefits over preceding engine technologies. However, GDI engines are associated with higher levels of particulate matter (PM) emissions, which is a major concern for human health. The aim of this work is to broaden the understanding of the effect of hydrogen combustion and the influence of the three way catalytic converter (TWC) on PM emission characteristics. The presence of hydrogen in GDI engines has been reported to reduce fuel consumption and improve the combustion process, making it possible to induce higher rates of EGR. A prototype exhaust fuel reformer build for on-board vehicle hydrogen-rich gas (reformate) production has been integrated within the engine operation and studied in this work.

Current progress in the development of diesel engines substantially contributes to the reduction of NOx and Particulate Matter (PM) emissions but will not succeed to eliminate the application of Diesel Particulate Filters (DPFs) in the future. In the past we have introduced a Multi-Functional Reactor (MFR) prototype, suitable for the abatement of the gaseous and PM emissions of the Low Temperature Combustion (LTC) engine operation. In this work the performance of MFR prototypes under both conventional and advanced combustion engine operating conditions is presented. The effect of the MFR on the fuel penalty associated to the filter regeneration is assessed via simulation. Special focus is placed on presenting the performance assessment in combination with the existing differences in the morphology and reactivity of the soot particles between the different modes of diesel engine operation (conventional and advanced). The effect of aging on the MFR performance is also presented.

The use of vanadia selective catalytic reduction (V-SCR) catalysts for NOX reduction from diesel engine exhaust is well known. These catalysts are also active for hydrocarbon (HC) and particulate matter (PM) oxidation. This dual functionality (oxidation and reduction) of V-SCR catalysts can help certain applications achieve the legislative limits with an improved margin. In this work, NOX reduction, HC and CO oxidation over V-SCR were studied independently and simultaneously in microreactor tests. The effect of various parameters (HC speciation, concentration, ANR, and NO₂/NOX ratio) was investigated and the data was used to develop a kinetic model. Oxidation of CO, C₃H₆, and n-C₁₀H₂₂ is first order in CO/HC, while C₇H₈ oxidation is less than first order in C₇H₈. All these reactions were zero order in O₂. Oxidation activity decreased in order: C₇H₈ ≻ n-C₁₀H₂₂ ≻ C₃H₆ ≻ CO. HC oxidation was inhibited by NH₃.

Producing on-board the hydrogen that is to be used as supplementary fuel by exhaust gas reforming of gasoline shows encouraging results. Extensive research has been done at the University of Birmingham towards on board generation of hydrogen-rich gaseous fuel. Exhaust gas reforming which utilizes water vapor and enthalpy from the hot engine exhaust gas was applied using a compact system of a fuel reformer reactor integrated with the three way catalytic converter (TWC). Such system can be fitted in the limited space close to the engine. The device has been designed and built in concentric shape with the catalytic converter as a core and the reformer in an annular shape outside, to best utilize the waste heat from the catalytic converter. It requires very little extra space beyond the baseline catalytic converter.

Particulate Matter (PM) emissions are of increasing importance, as diesel emissions legislation continues to tighten around the world. Diesel PM can be controlled using Diesel Particulate Filters (DPFs), which can effectively reduce the level of carbon (soot) emissions to ambient background levels. The Johnson Matthey Continuously Regenerating Trap (CRT®) [1], which will be referred to as the Continuously Regenerating DPF (CR-DPF) for the remainder of this paper, has been widely applied in Heavy Duty Diesel (HDD) applications, and has been proved to have outstanding field durability [2]. To widen the potential application of this system, addition of a platinum based catalyst to the DPF has been shown to lead to a higher PM removal rate under passive regeneration conditions, using the NOx contained in the exhaust gases.

The HSDI Diesel engine contributes substantially to the decrease of fleet fuel consumption thus to the reduction of CO2 emissions. This results in the rising market acceptance which is supported by desirable driving performance as well as greatly improved NVH behavior. In addition to the above mentioned requirements on driving performance, fuel economy and NVH behavior, continuously increasing demands on emissions performance have to be met. From today's view the Diesel particulate trap presents a safe technology to achieve the required reduction of the particle emission of more than 95%. However, according to today's knowledge a further, substantial NOx engine-out emission reduction for the Diesel engine is counteracts with the other goal of reduced fuel consumption. To comply with current and future emission standards, Diesel engines will require DeNOx technologies.

Catalyzed soot filters are being fitted to an increasing range of diesel-powered passenger cars in Europe. While the initial applications used silicon carbide wall-flow filters, oxide-based filters are now being successfully applied. Oxide-based filters can offer performance and system cost advantages for applications involving both a catalyzed filter with a separate oxidation catalyst, and a catalyzed filter-only that incorporates all necessary catalytic oxidation functions. Advanced diesel catalyst technologies have been developed for alternative advanced oxide filter materials, including aluminum titanate and advanced cordierite. In the development of the advanced catalyzed filters, improvements were made to the filter material microstructures that were coupled with new catalyst formulations and novel coating processes that had synergistic effects to give enhanced overall performance.

The future worldwide emission regulations will request a drastic decrease of Diesel engine tailpipe emissions. Depending on the planned application and the real official regulations, a further strong decrease of engine out emissions is necessary, even though the utilized exhaust after-treatment systems are very powerful. To reduce NOx emissions internally, the external exhaust gas recirculation (EGR) is known as the most effective way. Due to the continuously increasing requirements regarding specific power, dynamic behavior and low emissions, future air path systems have to fulfill higher requirements and, consequently, become more and more complex, e.g. arrangements with a 2-stage turbo charging or 2-stage EGR system with different stages of cooling performance.

The operation of NOx Adsorber catalysts (NAC), also often referred to as Lean NOx Trap catalysts or NOx Storage-reduction catalysts, entails frequent periodic NOx regeneration events. These are accomplished by creating a net reducing, fuel-rich environment in the exhaust. The reduction of hydrocarbon emissions which occur during such fuel-rich events is challenging, due to the oxygen-deficient environment. In order to overcome this limitation, two possibilities exist: (i) oxygen can be stored during lean phase, to be used for hydrocarbon slip oxidation in the subsequent rich phase, or (ii) unreacted hydrocarbons can be trapped during the rich phase and oxidized during the following lean phase. In this work, two groups of catalytic solutions were developed and evaluated for hydrocarbon emission control based on these approaches: an Oxygen Storage Compound (OSC) based catalyst and zeolite-based hydrocarbon trap catalyst.

This paper describes an alternative catalyst aging process using a hot gas test stand for thermal aging. The solution presented is characterized by a burner technology that is combined with a combustion enhancement, which allows stoichiometric and rich operating conditions to simulate engine exhaust gases. The resulting efficiency was increased and the operation limits were broadened, compared to combustion engines that are typically used for catalyst aging. The primary modification that enabled this achievement was the recirculation of exhaust gas downstream from catalyst back to the burner. The burner allows the running simplified dynamic durability cycles, which are the standard bench cycle that is defined by the legislation as alternative aging procedure and the fuel shut-off simulation cycle ZDAKW. The hot gas test stand approach has been compared to the conventional engine test bench method.

The aftertreatment challenge in the non-road market is making the same system work and fit not just in one machine, but in hundreds of different machines, some of which can be used for many different purposes. This huge diversity of applications and the relatively small unit numbers for each application, coupled with the rapid introduction of new standards and the very high performance needed from the engines and machines, requires a sophisticated approach to product development. Furthermore, as emissions requirements become ever more stringent, designing a system to meet the legislation subject to packaging and cost constraints becomes progressively more difficult. This is further exacerbated by increasing system complexity, where more than one technology may be required to control all the legislated pollutants and/or an active control strategy is involved. Also a very high degree of component integration is required.

A 1-D numerical model describing the ammonia selective catalytic reduction (SCR) de-NOx process has been developed based on data measured on a laboratory microreactor for a vanadia-titania washcoated catalyst system. Kinetics for various NH3-NOx reactions were investigated, as well as those for ammonia, CO and hydrocarbon oxidation. The model has been successfully validated against engine bench measurements, over light-off and ESC tests, under a wide range of conditions, e.g. flow rate, temperature, NO2/NO ratio, and ammonia injection rate. A very good agreement between the experimental data and the model has been achieved. The model has now been used to predict the effect of NO2/NO ratio on NOx conversion, and the effect of different ammonia injection rates on the efficiency of the SCR process.

The European research co-operation Lotus is presented. The main objectives of the project were i) to show the potential for a urea-based SCR system to comply with the EU standard of years 2005 and 2008 for heavy-duty Diesel engines for different driving conditions with optimal fuel consumption, ii) to reach 95 % conversion of NOx at steady state at full load on a Euro III engine, iii) to reach 75 % NOx reduction for exhaust temperatures between 200-300°C, and 85 % average NOx reduction between 200-500°C. The energy content of the consumed urea should not exceed 1.0 %, calculated as specific fuel consumption. These targets were met in May 2003 and the Lotus SCR system fulfilled the Euro V NOx legislative objectives for year 2008.

Today, SULEV legislation represents the most stringent emission standard for vehicles with combustion engines, and it will be introduced starting by Model Year 2003. In order to meet such standards, even higher effort is required for the development of the exhaust gas emission concept of SI engines. Beyond a facelift of the combustion system, exhaust gas aftertreatment, and the engine management system, new approaches are striven for. The principle keys are well known: low HC feed gas, high thermal load for quick light-off, exhaust system with low heat capacity and highly effective exhaust gas aftertreatment.

Electromechanical valve trains in camless engines enable virtually fully variable valve timing that offers large potential for both part load fuel economy and high low end torque. Based upon the principle of a spring-mass-oscillator, the actuator stores the energy to open and close the valves in springs. However, the motion of the valves and the electromechanical actuation suffers from parasitic losses, such as friction and ohmic resistance. Besides eddy current losses, gas forces obviously play a further important role in the control of exhaust valve opening especially at high engine speeds and loads. Based on engine test bench data, computational simulations (3D CFD, gas exchange process and electromechanical system) are carried out to analyze the effects of exhaust valve gas forces on the dynamic motion of valve and actuator. The modeling approach and results of this investigation are discussed in this paper.

The sound quality and performance of an automotive engine are both significantly influenced by the “air-to-air” system, i.e., the intake system, the exhaust system, and the engine gas dynamics. Only a full systems approach can result in an optimized air-to-air system, which fulfills engine performance requirements, overall sound pressure level targets for airborne vehicle noise, as well as sound quality demands. This paper describes an approach, which considers the intake system, engine, and exhaust system within one CAE model that can be utilized for engine performance calculations as well as acoustic simulations. Examples comparing simulated and measured sound are discussed. Finally, the simulated sound (e.g., at the tailpipe of the exhaust system) is combined with an interior noise simulation technique to evaluate its influence inside the vehicle's interior.

A one-dimensional numerical model for a Cu-zeolite SCR catalyst has been developed. The model is based on kinetics developed from laboratory microreactor data for the various NH₃-NOX reactions, as well as for NH₃ oxidation. The kinetic scheme used is discussed and evidence for it presented. The model is capable of predicting the conversion of NO and NO₂, NH₃ slip and the formation of N₂O, as well as effects associated with NH₃ storage and desorption. To obtain a good prediction of catalyst temperature during cold start tests, it was found necessary to include storage and desorption of H₂O in the model; storage of H₂O is associated with a sizable exotherm and the subsequent desorption of this water produces a correspondingly large endotherm.

In earlier work we have shown that engine operation with oxygenated fuels (e.g., biodiesel) reduces the particulate matter (PM) emissions and extends the engine tolerance to exhaust gas recirculation (EGR) before it reaches smoke limited conditions. The same result has also been reported when high cetane number fuels such as gas-to-liquid (GTL) are used. A likely mechanism for engine-out particulate growth is the reintroduction of particle nuclei into the cylinder through EGR. These recirculated PM particles serve as sites for further condensation and accumulation promoting larger and greater number of particles. In order to further our understanding of EGR influence on total PM production, a diesel particulate filter (DPF) was integrated into the EGR loop. A PM reduction of approximately 50% (soot) was achieved with diesel fuel through filtered EGR, whilst still maintaining a significant NOX reduction.